飞机燃油质量特性计算及供油顺序的设计

采用将油箱分割成多单元斜六面体的方法解决了外形复杂油箱的描述问题;采用切片法计算燃油质量特性,方法本身考虑了飞机姿态角对燃油形状的影响。解决了在给定重心活动范围情况下供油顺序设计问题。算例证明本方法具有很高的精确度和应用价值。     

吸热型碳氢燃料热沉的测定

介绍了一套自制的热导式高温量热系统,热量常数可用电标定法测定。用此仪器可测定各种吸热型碳氢燃料在各种条件下的热沉,用于吸热型碳氢燃料的筛选,为吸热型碳氢燃料的研究提供可靠的热化学数据。用这套装置测定了两种吸热型碳氢燃料在７００°Ｃ的热沉,与文献值接近。     

用固体吸附/分光光度法同时监测空气中的肼、一甲肼和偏二甲肼

介绍了用一甲肼浓缩采样采集空气中三肼混合气体,用分光光度法分别测出肼、一甲肼和偏二甲肼各组分的含量。测定结果通过标准气验证,相对误差小于１７％,各组份回收率均大于８０％。本方法适用于空气中低浓度三肼废气的测定。     

首次交会对接任务发射场加注安全保障改进

载人航天器加注是航天器研制过程中安全风险最高、危险作业工序最多的环节,必须采取严密的安全防护措施,确保万无一失.通过实践探索积累经验,全面周密的设计论证,对原有加注硬件条件进行改造,工作流程进行优化,从而大幅提高本质安全度,并在首次交会对接任务中加以应用和验证,取得了良好的效果,圆满完成了“天宫一号”、“神舟八号”发射...     

受平行壁限制的燃油喷雾二相流特征

通过试验诊断了燃油喷雾在模拟环形燃烧室火焰筒内、外壁面间的二相流型。其结果显示 ,与不受壁面限制的结果相比 ,其基本流型在下游有明显改变     

飞机燃油系统闪电试验可燃气体配比研究

飞机燃油系统闪电试验中,可燃气体混合配比体积分数的轻微变化对气体的点燃能量和点燃概率有重要的影响。采用混合配比体积分数不恰当的可燃气体可能会导致闪电试验欠考核或过严考核,进而影响对闪电防护设计有效性的准确评估。采用高精度的动态气体配比调控系统搭建了可燃气体点燃试验验证台架,通过试验对不同可燃气体配比体积分数下的最小点燃能量及相关点燃影响因素进行了研究和分析。研究表明:采用 5.0%氢气配比体积分数的可燃气体可检出 200 μJ及以上能量的全部点火源,同时可避免闪电试验被过度考核,推荐进行优先选配;随着氢气配比体积分数的增大,可燃气体点燃所需的点燃能量逐渐降低;氢气配比体积分数越高,燃油系统闪电试验被过度考核的程度就越大;鉴于可燃气体燃爆冲击的安全影响,不推荐燃油系统闪电试验采用 6.5%及以上氢气配比体积分数的可燃气体。试验数据及研究结论可为飞机燃油系统闪电防护设计及闪电试验提供参考和指导。     

Experimental Study on Emission Performance of an LPP/TVC

A key issue in the commercial aircraft engine design is environmental acceptability, and designers are continually challenged to reduce emissions. In this paper, an experimental investigation is performed to evaluate the emission performance of a liquid-fueled trapped vortex combustor (TVC) under lean premixed prevaporized (LPP) mode. When operating as an LPP system, a TVC is fueled both in the cavities and in the main stream. The correlations between the emission performance and the total excess air ratio, the positions (4 positions) of the fuel injectors in the main stream, and the inlet temperature are obtained. Experi- mental results show that both the volume concentrations of unburnt hydrocarbon (UHC) and NOx (NO, NO2 usually grouped together as NOx) increase with the increase of total excess air ratio from 1.5 to 3.0; the emission performance relies heavily on the position of the main stream injector, and the best performance is achieved at Position 4 in the experiments; the increase of the inlet temperature impacts on the emission performance positively; the smallest volume concentrations of UHC and NOx obtained in the experiment are 94×10 6 and 2.3×10 6 respectively. This paper validates the feasibility of low emissions for an LPP/TVC and provides a reference for further optimization of TVCs.     

供油瞬态喷油杆内燃油结焦机理及规律数值研究

为获得喷油杆通断循环供油工作模式下,供油瞬间燃油结焦速率陡增机理,本文建立起沿喷杆轴向的一维非稳态热-流-固耦合换热与燃油结焦计算模型。获得不同时刻壁温、油温与结焦速率等参数轴向分布。通过与连续供油模式下的结果进行对比,来分析供油瞬间灼热喷杆内壁对燃油热冲击的影响,以获得结焦速率陡增机理。结果表明通断供油模式下,供油瞬间会迅速形成一尖锐的油温和结焦前体浓度峰值,结焦固相表面反应被迅速激发,结焦速率陡增。在喷杆前端（x=100mm）与底部（x=260mm）附近各存在一结焦速率峰值区域。通断供油模式下,在x=100mm和x=260mm位置处,每个周期供油起始时刻结焦速率峰值分别在5000μg/cm2h和2000μg/cm2h左右,远大于连续供油下的值。但供油结束时刻,供油模式的影响大幅下降。此外通断供油下,供油瞬间热冲击对燃油结焦的影响沿喷杆轴向逐渐减小。减小喷杆供油流量,热冲击的影响有所下降,且随时间先升高后降低。提高进口油温,热冲击的影响显著减小,且随供油时间逐渐降低。     

基于旋转高频信号注入法的内置式永磁同步电机低速段转子位置检测及其误差补偿

旋转高频信号注入法注入信号较为稳定,且位置估计过程不依赖电机参数,因而十分适用于内置式永磁同步电机(IPMSM)的零、低速转子位置检测。针对传统高频信号注入法无法辨别磁极的问题,用电压方波注入法检测磁极,结合有限元软件仿真,来合理选取方波电压幅值和时长,有效缩短了磁极判断耗时。分析了滤波器和信号离散化对位置估计精度的影响,提出在低速段可用线段拟合带通滤波器中心频率处的相频特性曲线,推导所需补偿角度与电机转速的关系。在理论分析的基础上,采用基于DSP28335的样机平台进行试验,结果表明磁极判断过程稳定,耗时较短,补偿后的位置估计值相比补偿前有明显改善,调速过程中系统动态性能良好。     

Design and optimization of a novel electrically controlled high pressure fuel injection system for heavy fuel aircraft piston engine

The heavy fuel compression ignition engines are widely equipped as aircraft piston engines. The fuel injection system is one of the key technologies that determines the performance of engine. One of the main challenges is to precisely control the injected fuel quantity and flow rate in the presence of pressure fluctuation. This challenge is even more serious for heavy fuel. An original design for electrically controlled high pressure fuel injection system called Multi-Pumppressure-reservoirs fuel injection System(MPS) was demonstrated to reduce the pressure fluctuation and help keep injection stable. MPS was compared with an ordinary high pressure Common Rail fuel injection System(CRS). This work established one-dimensional AMESim and mathematical models for both CRS and MPS to study the effect of different structures and geometric parameters on the pressure fluctuations. The calculations show that the average fuel pressure fluctuation of MPS can be reduced by 57% for the crankshaft speed of 1900 r/min, and the pressure fluctuation before injection reduced by 100%. It is concluded that the pressure performance of MPS is less sensitive to pressure reservoir volume than that of CRS, and there is an opportunity for further volume reduction.