2219铝合金厚板TIG焊接头组织与力学性能研究

采用氦弧打底+氩弧填充、盖面的焊接工艺对2219-T87铝合金15 mm厚板进行TIG焊接试验，研究其焊缝成形和组织力学性能。结果表明，此工艺焊缝成形美观，无可见焊接缺陷，气孔抑制效果好，接头平均抗拉强度为278.22 MPa，平均断后延伸率为3.89%，接头平均强度系数达到58.94%。接头硬度整体表现为焊缝中心最低，从焊缝中心到母材呈现先增大后局部降低再增大的趋势；且焊缝中心填充层硬度高于打底层和盖面层。熔合区的微观组织为柱状树枝晶和胞状树枝晶，且垂直于熔合线生长，在靠近熔合区两侧出现了等轴细晶带。焊接接头断面有较多撕裂棱和韧窝，局部发现第二相粒子和微孔，其断裂机制为典型的韧性断裂。     

2524与7150铝合金激光焊T型接头的组织与性能

介绍了2524与7150铝合金激光焊T型接头优化的工艺参数,并研究了T型接头在优化工艺下的显微组织与力学性能,进行金相分析、显微硬度测试与接头拉伸试验。结果表明:优化工艺下焊缝没有裂纹、气孔,金相组织晶粒细小、致密,焊缝区域的硬度最低;T型接头x方向的拉伸强度达到384 MPa,z方向的拉伸强度为236 MPa。     

2219 铝合金单、双道焊接头性能分析

通过对比2219 铝合金单道氩弧焊和氦弧打底+氩弧盖面双道焊接头的常温及液氮温度拉伸性
能、显微硬度分布、单向拉伸过程的数字散斑测量(DIC)结果,发现在常、低温条件下双道焊接头的拉伸强度和
延伸率均比单道焊接头高10% ~20%,单道焊接头焊缝及热影响区内材料的显微硬度值相比母材的降低程度
比双道焊接头更为显著,其主要原因是单道焊接头的一次性热输入大于双道焊,材料受热影响更严重,焊漏高
度及形状的可控性更差。     

2195铝锂合金弧焊技术研究现状

铝锂合金具有密度低、比模量高、比强度高、抗疲劳及腐蚀性能良好等特点,被认为是航空航天领域最有应用前途的结构材料之一.本文回顾了铝锂合金的发展历程,介绍了新一代2195铝锂合金的成分、组织结构及可焊接性,分析其焊接过程出现的主要问题,概述了国内外机构通过优化2195铝锂合金配用焊丝及弧焊工艺,改善接头组织结构及力学性能的...     

Design and analysis of a novel hybrid cooling method of high-speed high-power permanent magnet assisted synchronous reluctance starter/generator in aviation applications

To improve the heat dissipation performance, this paper proposes a novel hybrid cooling method for high-speed high-power Permanent Magnet assisted Synchronous Reluctance Starter/Generator (PMaSynR S/G) in aerospace applications. The hybrid cooling structure with oil circulation in the housing, oil spray at winding ends and rotor end surface is firstly proposed for the PMaSynR S/G. Then the accurate loss calculation of the PMaSynR S/G is proposed, which includes air gap friction loss under oil spray cooling, copper loss, stator and rotor core loss, permanent magnet eddy current loss and bearing loss. The parameter sensitivity analysis of the hybrid cooling structure is proposed, while the equivalent thermal network model of the PMaSynR S/G is established considering the uneven spraying at the winding ends. Finally, the effectiveness of the proposed hybrid cooling method is demonstrated on a 40 kW/24000 r/min PMaSynR S/G experimental platform.     

Effect of adding Nb foil on joint properties of laser fusion welding for TC4 titanium and 7075 aluminum alloy

It is difficult to gain effective Ti-Al fusion welding joints due to their differences in thermal properties and the appearance of brittle Ti-Al Intermetallic Compounds (IMCs). The experiments of laser fusion welding for TC4 titanium and 7075 aluminum alloy were carried out, temperature field and ductility/brittleness, as well as chemical potential of elements, were calculated, and the effect of adding Nb foil on mechanical properties of the weld was also investigated. The results suggested that Nb atoms tend to diffuse toward Al side, which is conducive to the participation of Nb in the metallurgical reaction and contributes to forming the Ti-Nb-Al IMC layer at the interface. As the thickness of Nb foil increases, the tensile-shear force of joint climbs first but then declines, and reaches the highest value of 1663 N with 0.10 mm-thickness Nb foil, representing 58.38% enhancement compared with the non-added one. Adding Nb foil slows down the heat transfer as a blocker, and thus both the melting amount of Al and the mixing area of Ti and Al decrease. In addition, Nb alloying reduces the brittleness of the Ti-Al compound. Hence, the joint properties of titanium/aluminum are improved with the addition of Nb foil.     

Through-thickness heterogeneity in creep properties of friction stir welding 7B50-T7451 aluminum alloy thick plate joint: Experiments and modeling

Through-thickness heterogeneity in creep properties of 7B50-T7451 aluminum alloy Friction Stir Welding(FSW) joints was investigated. Creep tests for three slices of the FSW joint were conducted at the temperature of 150–200 °C and applied stress of 60–225 MPa. The theta projection method was used to predict creep curves and minimum creep rate. The results show that the minimum creep rate increases and creep rupture life decreases with the increase of creep temperature and applied stress. Creep p...     

推进剂管理装置的可靠性增长及试验验证

采用原始的焊接方式焊接筛网式推进剂管理装置的收集器合格率低、可靠性差。为此,采用纯钛箔作为过渡层进行了不锈钢筛网与钛合金支压板的电阻缝焊试验以及随后这两者与钛合金骨架的电子束焊试验,然后进行了地面力学环境下的振动试验,以验证焊接方式改进后收集器的可靠性。焊接试验结果表明,纯钛箔过渡层一方面可以大幅降低筛网在电阻缝焊时的焊接热量,有效地减小筛网的热变形;另一方面可以在电阻缝焊后形成牢固、封闭的纯钛/不锈钢筛网焊缝过渡区,有效地增加电子束焊时筛网的变形抗力,从而使得焊接后试样的合格率和性能大幅提高。振动试验结果表明,焊接方式改进后收集器的可靠度置信下限从0.90增加到了0.96。     

基于智能差分算法的摩擦力补偿方法研究

针对光电平台低速转动时，受摩擦力影响较大，使得速度跟随曲线出现“死区”现象，导致跟踪性能明显下降这一问题，提出了一种基于智能差分进化算法和Lurge摩擦模型的摩擦力补偿控制方法。通过采集记录光电转台正、反向匀速运动时的摩擦力大小，建立转台不同速度和摩擦力之间的对应关系。通过最小二乘法对摩擦模型静态参数进行分段拟合，采用智能差分进化算法辨识摩擦模型动态参数，并基于反馈的速度信息和获得的摩擦模型等效为摩擦补偿力矩输入到电流环控制输入端，实现平台平稳低速运行。实验结果表明：摩擦力补偿后速度响应误差由补偿前的±0.1°/s减小到±0.04 °/s，提出方法效果显著。