一种低位作业自动焊接方法--CO2焊与点焊在客车车身制造中的新运用

本文通过介绍一种客车顶盖蒙皮、顶骨架低位作业自动焊接方法,综合CO2气体保护焊和单面双点电阻焊,找出影响期焊接质量的原因及解决方法,以充分发挥其焊接变形小、焊接强度高、节能、高效的特点.     

Stability analysis of an aeroelastic system with friction

In this paper, harmonic balance method, exact formulation and numerical simulation method are adopted to study the effects of different friction stiffness on the stability of 1.5 degrees of freedom aeroelastic system. On this basis, the expressions of input energy and dissipated energy are deduced, and the energy method is used to reveal the mechanisms of the stable boundary and unstable boundary existing in the system and the effects of different friction stiffness on the stability of the system. Studies have shown that the stability region and the critical aerodynamic damping ratio of the system rise with the increase of the friction stiffness, while the friction stiffness has little effect on the stability boundary. In the analysis of the stability of system, the results of harmonic balance method, exact formulation and Newmark of numerical simulation method are in good agreement. Compared with exact formulation and numerical simulation method, the concept and conclusion of harmonic balance method are simple in the system stability analysis.     

Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

摩擦焊设备振动油缸的性能分析

液压式摩擦焊设备是将电液伺服控制技术运用到摩擦焊接领域的一种先进设备。通过分析系统振动油缸的频率,找出影响频率的关键因素,深入分析这些因素对振动油缸伺服控制系统的影响,并利用AMESim仿真软件对该系统进行建模分析,验证了分析结果,并总结出改进系统的几点措施,为摩擦焊设备的设计改进提供了理论依据。。     

壁面摩擦对风洞侧壁干扰的影响

本文研究了摩擦对风洞侧壁干扰的影响。在以Barnwell为代表开展的一系列侧壁干扰研究中,所有工作都未计及摩擦的影响。我们认为,Barnwell等人的这一处理理论上有缺陷。对此,本文用Karman-Pohlhausen方法对侧壁边界层作了分析,指出摩擦对侧壁干扰有不同程度的影响,具体取决于Pohlhausen参数B的大小;B越小,影响越大。Barnwell略去摩擦项的结果只对应于分离边界层情况,而事实上Barnwell处理的是附着边界层。通过这一分析,本文建立了有摩擦影响的侧壁干扰修正的新形式;考虑到多种因素的影响,初步建议参数B按中间值取为B=3～4。最后,就修正参数δ~*的确定作了一定讨论。     

液压泵摩擦副可靠性设计基本方法研究

阐述了液压泵摩擦副可靠性分析及设计的基本步骤和原则。作为实例,文中给出了滑靴耐磨可靠性设计所采用的（pv）应力模型新方法。     

改善反作用轮低速性能的补偿观测器方法

基于Ｄａｈｌ摩擦模型,给出了用于卫星姿态三轴稳定控制的反作用轮低速动力学方程,就反作用轮转速过零对卫星姿态产生的扰动现象进行了分析,提出了一种利用非线性观测器估计摩擦力矩,并予以补偿的补偿观测器方法。仿真结果表明,该方法改善了反作用轮低速性能,提高了卫星姿态控制的指向精度和稳定度。     

真空汽相焊冷却速率对多层板焊点质量的影响

为解决多层印制板真空汽相焊由于焊后冷却不足导致的焊点纹路问题,本文确定多层板焊点纹路出现的根本原因,对焊后冷却区进行改造,进而研究不同焊接工艺对焊点表面形貌、内部组织形貌及焊点力学性能的影响。实验结果表明,快冷下焊点形成的界面金属化合物（IMC）更薄,焊点组织也更加均匀,即Pb在Sn中的分布更弥散。快冷下形成的IMC层晶粒直径在1μm左右,剪切强度为17.26 MPa,较慢冷提高了43%,达到细晶强化的目的。此外,由于冷却速度过慢导致的焊点表面纹路缺陷也得到明显改善。     

非牛顿大滑滚比工况的斜齿轮热摩擦特性分析

考虑啮合过程中接触线长度及齿面载荷的时变性,结合沿接触线方向综合曲率半径及卷吸速度的瞬态特点,建立满足航空传动润滑剂非牛顿流体及大滑滚比工况的有限长线接触斜齿轮热弹流润滑(TEHL)模型。采用多重网格法及逐列扫描法,获得适用于宽泛工况范围的斜齿轮热弹流润滑完全数值解;分析非牛顿及大滑滚比情形下的斜齿轮传动热摩擦特性。结果表明:斜齿轮端部存在明显压力及温度尖峰,且离入口愈近膜厚会略减小;非牛顿特性对温度场影响显著,且接触线过节点时温度分布呈“V”型分布;摩擦因数沿啮合线方向在节点处接近于0且向两侧逐渐增大,同时随滑滚比的增大而增大。      

民用航空发动机TA19电子束焊疲劳试验

针对民用航空发动机钛合金整体叶盘常用材料TA19开展其母材试件与电子束焊焊接试件在20,300,450℃的疲劳试验,通过焊接试件的焊缝材料断口与母材断口形貌的比较探讨了焊缝材料的疲劳破坏机理,并在104~106循环的疲劳寿命区间内采用Basquin模型分别建立了焊缝材料和母材的应力-疲劳寿命(S-N)曲线,结果显示母材试件与焊接试件的试验疲劳寿命大部分都落在了对应模型计算疲劳寿命的2倍线之内,表明试验得到的S-N曲线是合理的.焊接试件与母材试件的S-N曲线的对比分析表明,20℃时焊接试件的疲劳性能比母材试件略高,而在300℃和450℃时焊接试件与母材试件的疲劳性能差异随应力水平发生变化.但总地说来,在所关注疲劳寿命区间内,母材试件与焊接试件的计算疲劳寿命差异也在2倍线以内,初步表明两者的疲劳性能相当.