10cm氙离子推力器变推力特性研究

非重力阻尼的连续、快速、高精度补偿是实现重力梯度测量卫星精细重力场测量的关键技术之一,直接影响到整星工程任务的成败。针对重力梯度测量卫星在轨飞行期间对电推进系统宽范围连续变推力能力的应用需求,分析了10cm氙离子推力器推力调节响应特性。在此基础上,通过对阳极电流、励磁电流和阳极流率等推力高敏感响应参量的组合调节,开展了推力调节试验研究,验证了10cm氙离子推力器宽范围连续变推力调节能力,获得了1～20mN范围内的推力调节性能及其变化规律。试验结果表明：在采用地面供电、供气设备条件下,10cm氙离子推力器能够在100～597W的功率范围内实现0.98～20.29mN的推力宽范围调节,比冲175～3500s,推力分辨率优于50μN。研究为建立10cm氙离子电推进系统的推力控制数学模型及调节控制算法奠定基础。     

基于响应曲面法的高速内冷铣削AISI304不锈钢铣削力

针对硬质合金刀具高速内冷铣削AISI304不锈钢时,切削力大、切削温度高及加工表面质量低的问题。基于响应曲面中心复合设计方法进行高速内冷铣削实验,建立了铣削力分量二阶回归预测模型,并进行了实验验证。对比了干式与内冷铣削后的加工表面质量,分析了铣削参数对铣削力分量的影响规律,以铣削力分量最小为目标优化了铣削参数。结果表明:进给力和径向力的预测值与实验值的误差分别为4. 77%和6. 16%;内冷铣削的Ra为0. 193～0. 327μm;对铣削力分量的影响是铣削深度转速进给量,随着铣削深度和转速的增加,进给力先升高后降低,径向力逐步增加,铣削深度与转速的交互作用对进给力和径向力的影响显著;转速11 643. 63 r/min、铣削深度1 mm、进给量0. 08 mm/r为最优铣削参数组合。     

基于非接触式测量的旋转叶片动应变重构方法

基于叶端定时非接触式测量和振动响应传递比的概念,开展高速旋转叶片动应变重构方法的研究。在频域内推导了叶片任意测点位移与任意测点动应变的传递比,给出了单模态共振下响应传递比关于位移和应变模态振型的解析表达式;建立旋转叶片的三维(3D)有限元模型,开展考虑旋转预应力效应的叶片模态分析,提取位移和应变模态振型,获得任意转速下叶端位移与叶根关键点动应变的传递比。开展高速旋转叶片叶端定时非接触式测量实验,采用周向傅里叶算法对叶端定时信号进行处理,获得叶片在不同转速单模态共振下的叶端位移,结合响应传递比,重构5个旋转叶片的关键点动应变。结果表明:旋转叶片在9000r/min和13000r/min转速下发生1阶共振时,与应变片实测结果相比,叶根处应力最大点、次大点和边缘点3个关键点的动应变平均重构误差均小于15%,验证了旋转叶片动应变重构方法的有效性。     

基于断口分析的钛合金轮内部缺陷损伤容限

为进行某轮损伤容限设计,开展了裂纹扩展断口分析和仿真分析研究。由断口分析可知:疲劳源为一处内部自然缺陷;依据疲劳辉纹确定了裂纹扩展速率;在裂纹长度为2 mm附近,裂纹扩展速率明显增大,为第一、第二加载阶段转换区域;裂纹稳定扩展区裂纹长度与裂纹扩展速率呈双对数线性关系;应用列表梯度法和Paris公式法反推了第二加载阶段的疲劳寿命,与该阶段实际循环次数的最大误差是163%。裂纹稳定扩展阶段裂纹扩展仿真值与断口反推值吻合;非稳定扩展阶段仿真值与断口反推值的最大误差为-215%;基于以上研究,合理确定了某离心轮内部裂纹表面扩展停机检测周期。该类轮非稳定、失稳扩展阶段寿命占内部裂纹表面扩展阶段寿命的比例达248%~357%,因此准确计算具有重要意义。     

基于PIV技术的单圆孔脉冲射流流场特征

对稳态射流及脉冲射流冲击靶板时的流场特性结构进行了探索和分析。采用高频粒子图像测速技术,在射流管口到冲击靶板间距为6倍管径的条件下,对稳态射流进口雷诺数为6 000的稳态射流及脉冲频率为20 Hz的脉冲射流进行了实验测量,得到了射流核心区、壁面射流区及滞止区内的速度分布。研究发现:①由于射流剪切作用的影响,脉冲射流核心区的最大轴向脉动速度为稳态射流的3倍。②滞止区内,由于射流的剪切作用和壁面的滞止作用,导致了脉冲射流轴向速度梯度最大为稳态射流的2倍,同时,滞止区内的最大脉动速度是稳态射流脉动速度的3倍。③脉冲射流对壁面的卷吸以及旋涡的产生和传播过程,破坏了壁面射流区稳定的速度边界层。相比稳态射流,脉冲射流的流场增加了湍流相干结构的含能并产生周期性的大尺度卷吸涡。     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.     

用于光波纳米推力器的颗粒供应技术和光聚积技术研究

为提高光波纳米推力器在轨应用的可行性,针对与其匹配的颗粒供应技术和光聚积技术进行研究。提出整个推进系统的设计思路,通过建立理论计算和数值计算模型,分析颗粒供应技术和光聚积技术的各项核心结构参数的设计方法。计算结果表明:颗粒供应装置的正负电极内径之比(W/D)会影响正负电荷产生的总量之比,在W/D=300/322附近时,正负电荷比例接近1:1。静电诱导电压为9 V,当中和通道长度大于37.5mm时,正负颗粒可以视为完全中和。光聚积设计思路可令聚积球对光能的利用率在32.8%左右。两种相关技术的装置与推力器在结构上能够对接、在性能上可以匹配,从理论上表明了两种支撑技术的可行性。     

无人机系统的安全性与危险源分析

无人机系统的战术性能及优势将使其在未来高技术战争和民用航空中发挥越来越重要的作用。然 而,由于有人机与无人机飞行事故的特点不同,使得有人机的安全性分析与管理措施不完全适用于无人机系 统。首先,对无人机系统的飞行事故进行统计分析,得出无人机系统事故的特点;然后,合理借鉴有人机的安全 性分析,定义无人机系统的安全性,提出无人机系统事故的严酷度等级划分及相应的危险可接受度;最后,从设 计、机组训练及使用操作三方面进行危险源分析。本文提出的无人机系统不安全事件发生可能性等级划分和 危险源定性分析,可为后续无人机安全管理框架的构建奠定基础。