脉冲爆震燃烧室出口燃气能量分布特性

为了提高脉冲爆震燃烧室出口燃气能量转换效率,采用数值计算方法,研究了带气动阀和爆震增强结构的脉冲爆震燃烧室出口燃气能量分布特性,结果表明:脉冲爆震燃气的膨胀过程先后经历一次膨胀、二次膨胀和过度膨胀3个阶段,单个周期内二次膨胀阶段的时间和能量占比最大;燃烧室出口燃气压力势能、动能、内能和能流密度的分布主要受燃气压力的影响,且变化规律与燃气压力一致;一次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的479%、259%、251%;二次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的502%、576%、581%。     

高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.     

端壁抽吸对压气机叶栅间隙泄漏流控制策略的研究

为了研究压气机机匣端壁抽吸对间隙泄漏流动控制的可行性和有效性,以高负荷压气机叶栅为研究对象,通过数值模拟方法对不同抽吸位置和抽吸流量率控制参数下的计算工况进行了对比和分析。研究结果表明:端壁抽吸可以直接地影响叶尖泄漏流的结构形态和存在形式,减弱叶尖泄漏流的强度和影响范围,进而提升压气机叶栅的性能;当抽吸槽覆盖范围包含叶尖泄漏流形成位置及稍靠后附近区域时,所对应的抽吸方案具有较好的控制效果,在0°攻角和0.5%的抽吸流量条件下前槽抽吸和中槽抽吸分别可获得7.04%和7.76%的叶栅总压损失增益;并且进一步研究发现端壁抽吸流量率存在上临界值,应针对不同攻角工况,在其相应的临界值范围内选择合理的抽吸流量,以达到用较小的吸气量实现对间隙泄漏流的控制。     

某型装备轴承件无失效时的可靠性参数估计

针对寿命服从威布尔分布的某型装备轴承件在无失效数据时的可靠性参数估计问题,首先,以失效概率为待估参数,取其先验分布为Beta分布,在2个超参数的先验密度函数为2种不同情形下,建立了失效概率的2种EBayes估计模型,分析了稳健性、渐近性和单调性;然后,对威布尔分布参数进行了加权最小二乘估计,进而建立了可靠度的2种E-Bayes估计模型,分析了稳健性和单调性;最后,结合实例数据进行了可靠性参数估计与分析,指出第2种估计模型更加合理有效。     

瞬变流速作用下姿控发动机燃料管路的非线性振动特性分析

为研究瞬变流速激励下某型卫星姿控发动机燃料输送管路的非线性振动特性,采用加权余量法和四阶Runge—Kutta法对燃料输送管路的非线性液固耦合振动模型进行了数值仿真,研究不同燃料流速下、电磁阀开关时长对燃料管路非线性振动稳定性的影响.仿真结果表明,依据管路特征线可将管路振动分为稳定振动区和不稳定振动区,且不稳定振动主要...     

基于自适应容积粒子滤波的车辆状态估计

针对车辆状态估计中由模型的强非线性、噪声的非高斯分布等相关因素导致估计精度下降甚至发散的问题,本文提出了基于自适应容积粒子滤波(Adaptive cubature particle filter,ACPF)的车辆状态估计器。首先基于非稳态动态轮胎模型,构建高维度非线性八自由度车辆模型。其次利用自适应容积卡尔曼滤波(Adaptive cubature Kalman filter,ACKF)算法更新基本粒子滤波(Particle filter,PF)算法的重要性密度函数,以完成自适应容积粒子滤波算法设计。利用车载传感器信息,运用ACPF算法实现对车辆的侧倾角、质心侧偏角等关键状态变量高精度在线观测。搭建Simulink-Carsim联合仿真平台进行了算法的验证,结果表明该算法状态估计精度高于传统无迹粒子滤波(Unscented particle filter,UPF)算法,且算法运算效率高于UPF算法,而传统PF估计值发散。研究结果为实现车辆动力学精准控制提供了理论支持。     

舱段结构热振耦合环境下仿真分析

针对武器装备对环境适应性要求不断提高的现状,以某舱段结构为研究对象,基于高加速应力筛选试验(HASS)条件,研究了结构在温变-振动耦合环境下的失效机理。首先,结合HASS试验剖面,确定了载荷条件,建立有限元模型;其次,采用ANSYS Workbench软件分析得到结构温度场分布及应力响应,确定了结构危险位置,并对其疲劳寿命进行计算分析,为舱段结构的失效分析及HASS试验剖面的合理制定提供依据和指导。     

火星大气来流模拟装置CFD仿真与试验

根据我国火星着陆巡视器工作过程,其着陆发动机需要在相对火星大气高速迎风运动中可靠点火。由于巡视器着陆时发动机喷管出口气流与火星稀薄气流方向相反,目前无法通过理论计算准确获得着陆过程的动态流场对发动机起动过程的影响量值。为验证火星着陆环境下发动机点火的适应性,需要建立发动机的火星大气来流试验环境模拟条件。为模拟发动机在火星大气条件下的相对运动,在真空舱内发动机保持固定,前端设置环形来流形成装置,该装置在发动机喷管周围形成一定速度的逆向来流包络。采用数值模拟技术结合试验验证方法,在火星着陆器巡视器主发动机性能考核试验中,针对来流的形成装置开展了设计研究工作。来流模拟试验测试数据表明:在确保贮箱供应压力稳定的条件下,来流模拟系统能够形成100~200 m/s速度的稳定来流,发动机在来流下能稳定启动工作,真空舱压力满足试验要求。