基于时标分解的弹性高超声速飞行器智能控制

考虑弹性高超声速飞行器纵向动力学模型，提出了一种基于时标分解的智能控制方法。考虑刚体状态和弹性模态具有不同的时标特性，采用奇异摄动理论进行快慢时标分解，将模型转换为刚体慢变子系统和弹性快变子系统。针对刚体子系统考虑动力学不确定，基于平行估计模型构造表征不确定逼近效果的预测误差，结合跟踪误差给出复合学习控制策略。针对弹性子系统设计自适应滑模控制稳定弹性模态。通过李雅普诺夫稳定性分析可证系统状态一致终值有界。仿真表明所提出的控制方法能够实现刚弹模态的稳定收敛，且具有更高的跟踪精度、更好的学习性能和更快的收敛速度。     

Remote-controlled flexible pose measurement system and method for a moving target in wind tunnel

The measurement of position and attitude parameters for the isolated target from a high-speed aircraft is a great challenge in the field of wind tunnel simulation technology. This paper proposes a remote-controlled flexible pose measurement system in wind tunnel conditions for the separation of a target from an aircraft. The position and attitude parameters of a moving object are obtained by utilizing a single camera with a focal length and camera orientation that can be changed based on different measurement conditions. Using this proposed system and method, both the flexibility and efficiency of the pose measurement system can be enhanced in wind tunnel conditions to meet the measurement requirements of different objects and experiments, which is also useful for the development of an intelligent position and attitude measurement system. The position and the focal length of the camera also can be controlled remotely during measurements to enlarge both the vertical and horizontal measurement range of this system. Experiments are conducted in the laboratory to measure the position and attitude of moving objects with high flexibility and efficiency, and the measurement precision of the measurement system is also verified through experiments.     

A novel control method for turboshaft engine with variable rotor speed based on the Ngdot estimator through LQG/LTR and rotor predicted torque feedforward

In order to compensate for the disturbance of wide variation in rotor demanded torque on power turbine speed and realize the fast response control of turboshaft engine during variable rotor speed, a cascade PID control method based on the acceleration estimator of gas turbine speed (Ngdot) and rotor predicted torque feedforward is proposed. Firstly, a two-speed Dual Clutch Transmission (DCT) model is applied in the integrated rotor/turboshaft engine system to achieve variable rotor speed. Then, an online estimation method of Ngdot based on the Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR) is proposed for power turbine speed cascade control. Finally, according to the cascade PID controller based on Ngdot estimator, a rotor demanded torque predicted method based on the Min-batch Gradient Descent-Neural Network (MGD-NN) is put forward to compromise the influence of rotor torque interference. The simulation results show that compared with cascade PID controller based on Ngdot estimator and the one combined with collective pitch feedforward control, the novel control method proposed can reduce the overshoot of power turbine speed by more than 20%, which possesses faster response, superior dynamic effect and satisfactory robustness performance. The control method proposed can realize the fast response control of turboshaft engine with variable rotor speed better.     

航空发动机低压转子系统的“可容模态”设计及实验验证

建立了带弹性支承和阻尼器的航空发动机低压柔性转子动力学模型,进行了模态计算以及临界转速处的响应计算。在考虑临界转速约束与“临界跟随”现象约束的条件下,综合模态不平衡影响因子、弹支应变能占比以及套齿连接结构稳定性构造了可容度评价函数,建立了低压转子系统的“可容模态”优化设计方法。设计并搭建了低压转子实验系统,从模态测试实验、阻尼器减振实验以及长时间“共振”实验,验证了设计方法的可靠性。研究结果为计算的临界转速与实际测量的临界转速最大误差为3.86%,阻尼器在1阶与2阶临界转速处的减振比最大可达45.6%,实验转子系统在1阶与2阶临界转速处各完成了长达412.5 s和429.8 s的“共振”实验,共振过程中转子系统各通道振动单峰值稳定在100μm以内,且无次谐波产生。表明了所建立的航空发动机低压转子系统“可容模态”优化设计方法是可行的。     

涡轮动叶表面换热特性的试验研究

航空发动机性能的提高对涡轮叶片耐热极限提出了更高的要求,为了更准确地分析涡轮叶片的传热特性,选取某型气冷涡轮动叶10%、50%和90%叶高的特征型面通过低导热光敏树脂材料经过3D打印而成,通过叶片表面粘贴厚度为0.02mm康铜加热膜接通恒定电流加热,使用红外热像系统精确测量叶片壁面温度,在平面叶栅中研究了吹风比(M)和雷诺数(Re)对气膜绝热冷却效率和努塞尔数(Nu)的影响(试验中基于弦长的进口雷诺数Re为8.0×10⁴-16.7×10⁴,吹风比M为1-3)。试验结果表明：M=1时气膜能够较好附着在叶片表面,叶片表面得到较好冷却;随着主流雷诺数的增加,绝热壁面温度逐渐升高,绝热效率逐渐降低;吹风比对涡轮叶片的传热特性的影响与气膜孔出流角度有关,随着吹风比的增大,压力面绝热冷却效率逐渐增大,由于吸力面的气膜孔出流角较大,吹风比增大使得吸力面的绝热冷却效率逐渐减小;随着吹风比的增加,对流换热系数增大。     

机匣沟槽对微型轴流涡轮叶尖泄漏流动的影响

本文通过对某微型涡喷发动机的单级轴流式涡轮进行机匣设计,采用剪切应力输运(SST)模型求解定常黏性雷诺平均Navier-Stokes方程,研究了不同机匣沟槽结构对其叶尖泄漏流动的影响。计算结果说明：当全机匣沟槽结构的叶顶浸入沟槽即d/c＞1.0时,封严效果较好;相较于全机匣沟槽结构,后开式机匣沟槽结构的封严效果更好, 随着沟槽前缘间隙的增大,封严效果减弱;沟槽深度a/c=1时,封严效果最佳,即泄漏流明显减弱,同时效率减小量较小。     

应用能量－Casimir方法研究充液卫星系统的运动稳定性

利用能量－Ｃａｓｉｍｉｒ方法研究了带４个挠性粱的充液卫星系统在无外力矩状态下,关于绕铅垂轴稳态转动的非线性稳定性条件,该条件考虑了液体的涡旋、弹性梁的振动、卫星主刚体的旋转以及流－弹－刚之间的耦合,此外还考虑了离心力与Ｃｏｒｉｏｌｉｓ惯性力的影响。推广了Ｒｕｍｊａｎｔｓｅｖ和Ｍａｒｓｄｅｎ的部分结果,为带挠性粱的充液航天器的运动稳定性总体设计提供了可靠的理论依据。     

面向设计的复合材料旋翼桨叶动力优化设计

提出一种面向设计的复合材料旋翼桨叶结构动力优化方法。采用典型剖面设计、变量连接、铺层变量连续化等方法,有效地处理了剖面内部形状、复合材料铺层、配重质量３类设计变量。在动力分析模型中考虑了剖面翘曲、耦合变形和陀螺力的影响,由三级数值计算模式实现固有频率灵敏度分析。约束条件包括了固有频率、结构重量、自转惯量等设计要求,优化求解采用基于序列二次规划的算法。上述方法真实反映了桨叶结构特征和实际工程设计要求。     

裂纹转子非线性振动特征的谐波小波与分形识别

通过对谐波小波的分析研究,指出了谐波小波对振动信号局部频段分析的优良特性。采用谐波小波对裂纹转子的非线性振动信号在低频段进行了分析。理论分析与实验结果表明:对实际裂纹转子信号,经谐波小波的频段分析后,能够得到通常难以由理论分析与实验结果获得的非整数倍周期分叉的非线性特征频谱。计算了裂纹转子的分形维数,发现裂纹转子的振动信号比理论结果要复杂、可以用多重分形作为判断实际转子是否有裂纹的一个特征。提出了用谐波小波变换后的奇异谱来识别裂纹转子非整数倍周期分叉的非线性特征频谱的方法,并对实际转子信号进行分析,得到了明显的非整数倍周期分叉的奇异谱。      

构架式天线柔性动力学建模与展开精度分析

构架式可展开天线具有结构非线性强、桁架系统复杂以及运动环节多等特点,通常被视作刚体系统进行建模分析。然而多刚体动力学方法在求解复杂的连杆结构时,难以处理数量大、非线性强的铰接间隙模型,因此并不能准确还原真实的结构特性,给构架式天线的地面展开验证带来很大困难。本文建立了一套适用于该型天线的柔性多体动力学模型,通过引入微小弹性形变来消除铰链间隙对天线展开的影响,并在型面精度方面与期望的天线展开模型进行了比较说明。在确保不影响结构真实性的前提下,通过降阶、引入稳定系数等手段提高了柔性体单元计算效率。通过约束方程的设计与模块拆分求解等方法,消除结构非线性的影响。解决了针对构架式可展开天线的复杂桁架系统强非线性动力学的高精度建模问题,为构架式天线的仿真提供了技术手段。