多等级区域侦察弹性星座设计方法

针对传统侦察星座目标单一、弹性低的问题，提出了多等级区域侦察弹性星座的设计方法。该方法将星座设计过程按区域等级信息分为多个子星座逐步设计，直到整体星座对所有的区域性能满足设计要求。以区域被划分为3个等级为例，首先对星座设计需求、设计指标及设计步骤进行了分析。其次推导了地面最低分辨率和轨道高度的关系并确定了不同子星座的轨道高度。最后考虑轨道倾角、一箭多星发射、光照和升交点漂移同步约束，构建基础星座、子星座1和子星座2的优化模型。最终设计星座为3层混合星座，共8个轨道面和70颗卫星，星座对各等级区域的最大重访时间分别为10937s，12241s和17437s，弹性指数为2213%，2420%和6361%。结果表明该方法设计的星座可实现对区域覆盖和弹性分级的设计要求，证明了方法的有效性。对比Walker星座设计方法，在同等设计要求下，Walker星座所需卫星数为156颗，多等级区域侦察弹性星座所需卫星数远低于Walker星座，结果进一步证明了该星座设计方法的优越性。     

基于伴随方法的单级低速压气机气动设计优化

采用梯度方法对某型4.5级压气机最后级进行气动设计优化研究，梯度由连续伴随方法计算确定，多排伴随方程采用伴随掺混面模型进行数值求解。首先，采用基于经验修正的初步设计方法设计带进口导叶的4.5级低速、低压缩比压气机的原始气动外形。之后，在压气机近失速工况对最后级静子叶片进行伴随气动设计优化，通过优化叶型和安装角降低流动损失，目标函数定义为加权求和形式的熵增和流量偏差，优化中对流量进行约束。最后，开展基于伴随方法的多工况气动设计优化研究，改善两个不同转速条件下最后级的气动性能。优化结果表明，基于伴随方法的多排气动设计优化可以通过改变叶片气动外形提升多排全工况气动性能。     

Applications of structural efficiency assessment method on structural-mechanical characteristics integrated design in aero-engines

In the design process of advanced aero-engines, it is necessary to carry out an effective analysis method between structural features and mechanical characteristics for a better structural optimization. Based on the structural composition and functions of aero-engines, the concept and contents of structural efficiency can reflect the relation between structural features and mechanical characteristics. In order to achieve the integrated design of structural and mechanical characteristics, one quantitative analysis method called Structural Efficiency Assessment Method (SEAM) was put forward. The structural efficiency coefficient was obtained by synthesizing the parameters to quantitatively evaluate the aero-engine structure design level. Parameterization method to evaluate structural design quality was realized. After analyzing the structural features of an actual dual-rotor system in typical high bypass ratio turbofan engines, the mechanical characteristics and structural efficiency coefficient were calculated. Structural efficiency coefficient of high-pressure rotor (0.43) is higher than that of low-pressure rotor (0.29), which directly shows the performance of the former is better, there is room for improvement in structural design of the low-pressure rotor. Thus the direction of structural optimization was pointed out. The applications of SEAM shows that the method is operational and effective in the evaluation and improvement of structural design.     

企业知识生态系统内生与外生协同机制研究

通过对企业知识生态系统协同机制的研究,设计知识生态系统内生和外生协同机制.内生协同机制包括企业知识生态系统战略协同机制、内部环境协同机制、领导协同机制、知识主体协同机制、激励协同机制的设计.外生协同机制包括外部环境协同机制设计、行业发展协同机制设计、技术协同机制设计,从而保障企业知识生态系统正常运行.     

某框基于后置程序逆向设计及数字化高效加工研究

介绍了飞机某框从逆向设计到数字化高效加工详细流程,应用以CATIA V5、VERICUT为代表的先进数字化制造技术,使零件数字化设计、数字化加工、工艺流程得到全面改进,为今后零件逆向设计及数字化加工奠定良好的基础。     

Multiscale topology optimization using feature-driven method

This paper presents a multiscale design method for simultaneous topology optimization of both macrostructures and microstructures. Geometric features are extended as design primitives at both macro and micro scales and represented by Level Set Functions (LSFs). Parameters related to the locations, sizes, and orientations of macro and micro features are considered as design variables and optimized simultaneously. In the overlapping areas of different macro features, embedded microstructures are optimally figured out as the solution of the corresponding sub-optimization problem. In this study, the eXtended Finite Element Method (XFEM) is implemented for structural and sensitivity analyses with respect to design variables. This method has the advantage of using a fixed grid independent of the topology optimization process. The homogenization procedure is applied to calculate the effective properties of considered microstructures in each macro feature. Numerical examples are presented to illustrate the effectiveness of the proposed method. Results depict that the multiscale design cannot obviously improve structural stiffness compared with a solid-material design under the linear elastic condition.     

论荀子的“勇”

荀子根据"勇"与"义"、"利"的关系提出了"狗彘之勇"、"贾盗之勇"、"小人之勇"、"士君子之勇",只有"士君子之勇"是值得提倡的。荀子还将"勇"划分为上勇、中勇、下勇,认为只有上勇才是真正的大勇。真正的勇并不是先天具有的,是后天"人为"的结果,需要重视礼的作用,树立重义轻利的求荣避辱观念,通过师法不断培养才能形成。     

Assessment on critical technologies for conceptual design of blended-wing-body civil aircraft

Civil aviation faces great challenges because of its robust projected future growth and potential adverse environmental effects. The classical Tube-And-Wing(TAW) configuration following the Cayley's design principles has been optimized to the architecture's limit, which can hardly satisfy the further requirements on green aviation. By past decades' investigations the BlendedWing-Body(BWB) concept has emerged as a potential solution, which can simultaneously fulfill metrics of noise, emission and fuel burn. The purpose of the present work is to analyze the developments of critical technologies for BWB conceptual design from a historical perspective of technology progress. It was found that the high aerodynamic efficiency of BWB aircraft can be well scaled by the mean aerodynamic chord and wetted aspect ratio, and should be realized with the trade-offs among stability and control and low-speed performance. The structure concepts of non-cylinder pressurized cabin are of high risks on weight prediction and weight penalty. A static stability criterion is recommended and further clear and adequate criteria are required by the evaluations of flying and handling qualities. The difficulties of propulsion and airframe integration are analyzed. The energy to revenue work ratios of well-developed BWB configurations are compared,which are 31.5% and 40% better than that of TAW, using state-of-art engine technology and future engine technology, respectively. Finally, further study aspects are advocated.     

Contingency target assessment,trajectory design,and analysis for NASA’s NEA scout solar sail mission

The presented study examines contingency target selection and trajectory design for NASA’s Near-Earth Asteroid Scout mission under the assumption of a missed lunar gravity assist. Two previously considered asteroids are selected as potential targets for the given scenario based on favorable orbital characteristics for launch dates ranging from June 27, 2020 through July 26, 2020. Initially, a simplified circular restricted 3-body problem + ideal solar sail model is utilized to survey trajectory options for a month-long launch window. Selected solutions from this data set are then converged in an N-body ephemeris + non-ideal sail model. Results suggest that NEA Scout can still perform asteroid rendezvous mission under the missed lunar gravity assist scenario with new targets, 2019 GF1, 2018 PK21, and 2007 UN12, based on the target launch dates. Further target assessment is carried out for 165 days beyond the current June 27, 2020 launch date.     

Application of a PCA-DBN-based surrogate model to robust aerodynamic design optimization

An efficient method employing a Principal Component Analysis (PCA)-Deep Belief Network (DBN)-based surrogate model is developed for robust aerodynamic design optimization in this study. In order to reduce the number of design variables for aerodynamic optimizations, the PCA technique is implemented to the geometric parameters obtained by parameterization method. For the purpose of predicting aerodynamic parameters, the DBN model is established with the reduced design variables as input and the aerodynamic parameters as output, and it is trained using the k-step contrastive divergence algorithm. The established PCA-DBN-based surrogate model is validated through predicting lift-to-drag ratios of a set of airfoils, and the results indicate that the PCA-DBN-based surrogate model is reliable and obtains more accurate predictions than three other surrogate models. Then the efficient optimization method is established by embedding the PCA-DBN-based surrogate model into an improved Particle Swarm Optimization (PSO) framework, and applied to the robust aerodynamic design optimizations of Natural Laminar Flow (NLF) airfoil and transonic wing. The optimization results indicate that the PCA-DBN-based surrogate model works very well as a prediction model in the robust optimization processes of both NLF airfoil and transonic wing. By employing the PCA-DBN-based surrogate model, the developed efficient method improves the optimization efficiency obviously.