基于碳纳米管薄膜的复合材料层间增韧

通过浮动催化化学气相沉积法制备连续碳纳米管薄膜,并将其原位沉积到单向碳纤维织物表面,手工铺层后借助真空辅助树脂传递模塑成型（VARTM）工艺制备碳纳米管-碳纤维/环氧树脂复合材料层压板,研究不同面密度的碳纳米管薄膜对层压板Ⅱ型层间断裂韧性的影响。结果表明,随着碳纳米管薄膜面密度的增加,层压板Ⅱ型层间断裂韧性先逐渐提高,当碳纳米管薄膜面密度为9.64 g/m²时,层压板Ⅱ型层间断裂韧性最佳,与原始层压板相比提高了94%。碳纳米管通过桥接树脂裂纹、从树脂中拔出等方式提高层间断裂韧性。当碳纳米管面密度超过临界值时,会引起树脂浸润困难,导致增韧效果降低。     

纵向波纹隔热屏气膜冷却特性实验

针对加力燃烧室纵向波纹隔热屏气膜冷却效果开展了细致的实验研究,利用红外热像仪测量了隔热屏壁面的温度分布,分析了隔热屏板型、吹风比、开孔率等参数对气膜冷却效率的影响。实验中板型选取了平板和纵向波纹隔热屏,吹风比变化范围是0.5~3.0,开孔率变化范围是1.4%~3.7%。结果表明:相比于平板隔热屏的气膜冷却效率沿程逐渐增加,纵向波纹隔热屏的气膜冷却效率随波纹板的起伏而起伏且大于平板隔热屏;随着吹风比的增加气膜冷却效率逐渐加大,在吹风比为3.0时达到最大值;气膜冷却效率在波峰处低,波谷处高,整体上随波纹板的起伏而波动,吹风比越小,气膜冷却效率随波纹板的起伏变化越明显;高吹风比(吹风比为2.0~3.0)下,气膜冷却效率沿程变化与增幅较为缓慢;整体上,随着开孔率的增加气膜冷却效率逐渐加大,小开孔率(开孔率为1.4%、2.7%)下的气膜冷却效率相差不大,但在次流背风侧,开孔率小的气膜冷却效率要小于开孔率大的气膜冷却效率。      

螺旋槽端面气膜密封结构高温特性研究

为了研究螺旋槽端面气膜密封结构在高温下的密封性能,建立了高温密封分析数学模型,研究了螺旋槽气膜密封的气膜温度、压力以及端面变形分布规律,在此基础上探讨了螺旋槽气膜密封的热变形机理,并进一步分析了不同密封压力、转速、环境温度下热效应对开启力和泄漏率的影响。结果表明:在高压、高速条件下,热效应使端面形成发散间隙,导致开启力减小,泄漏率增加;在低压、高速条件下,热效应使端面形成收敛间隙,导致开启力及泄漏率增大。对于螺旋槽端面气膜密封结构,环境温度的升高对端面变形的影响不明显,且环境温度从300 K升至550 K时,考虑端面热效应的开启力减小4%,泄漏率减少36%。     

突片作用下气膜冷却效率的试验研究

为了研究突片对气膜冷却的影响规律, 设计了3种不同堵塞比的等边三角形突片, 并对其对气膜冷却特性的影响规律进行了实验研究.研究结果表明, 与无突片的气膜冷却相比, 突片的存在提高了气膜冷却效果;冷却效率随吹风比的增加而增大, 且沿气流方向冷却效率存在一极大值;当吹风比M<1.5时, 冷却效率随吹风比的增加而增大;当M>1.5时, 冷却效率随吹风比的增加而减小.      

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

The role of AVDR in linear cascade testing

Linear cascade testing plays an important role in the research and development of turbomachinery and is widely used over the world.The ideal cascade model of a turbomachinery blade row is two-dimensional.In actual linear cascade testing, the flow through the test section converges due to the development of the boundary layer and secondary flow along the sidewall surfaces of the test section.Axial velocity density ratio(AVDR) is adopted to account for the deviation of the tested cascade flow from the ideal 2D model.Among numerous published cascade works, the influence of AVDR on cascade performance is seen to be complicated with many affecting factors, such as those related to cascade/blade geometry and flow conditions.Also, controlling AVDR is limited by the facility capability.Furthermore, real blade-to-blade flow in turbomachines is usually associated with AVDR greater than unity due to limited span of blades between the hub and shroud such that cascade testing without reducing AVDR could be favored sometimes.All these facets add complexity and diversification to the matter.The current paper reviews previous studies and results on AVDR.Consolidated understanding on the role of AVDR and recommendations on how to deal with it in linear cascade testing are provided.      

基于伴随非等温射流理论的缝槽气膜冷却模型

在伴随非等温射流基础上发展了一种适用于缝槽气膜冷却绝热温比预估的数学模型.通过合理假设推导出二维壁面射流混合层核心温度分布规律,将其作为气膜绝热壁温,并考虑缝槽几何特征参数和气膜吹风比对冷却效率的影响,得到绝热温比计算公式.用试验数据对该预估模型进行拟合分析,得到了与试验数据拟合精度在±8%以内的半经验预估模型,证明该模型的可行性和应用潜力,并需要更多的试验数据对其进行验证和改进.      

喷雾器喷嘴出口喷流流场特性的实验研究

通过定性定量实验手段研究了以水为单介质流体的某农用喷雾器喷嘴出口流场。首先采用单反相机常规拍摄方法,记录了喷雾压力在50～4 000 Pa范围内的喷嘴出口流场,发现了随着喷雾压力增大,喷嘴出口射流的形状经历了形成液泡到液泡破裂的过程,以及射流发展及最终稳定过程。然后通过PIV测速技术对喷雾压力在1 000～4 000 Pa范围内的喷嘴出口流场进行了定量测量实验研究,获得了在纵向截面上,喷嘴出口速度随喷雾压力增大而增大,且在中心线上的速度随着离喷口距离的增加均呈现振荡衰减的变化规律。在同一位置横向截面上,随着喷雾压力的增加,旋流强度越强,流速越大;而在同一喷雾压力下,离喷嘴出口距离越近的横截面处旋流强度越大,流速也越大。本文实验研究结果验证了PIV测速技术可以用于水雾滴的速度场测量。     

GPS/INS组合系统空中对准方法研究

针对单天线的GPS与捷联惯性导航组合系统,提出了一种空中对准方案,不同于传统的传递对准方法,仅依靠GPS测量信息进行速度匹配,完成空中初始对准。该方案采用扩展卡尔曼滤波方法解决对准过程中的非线性问题。仿真结果表明该方案的对准精度(1σ)可以达到水平姿态误差0.07,°方位误差0.3°。     

复合材料层合板低速冲击损伤的预测模型

在低速冲击载荷作用下,建立了一种适用于铺层总数较多的复合材料层合板的损伤预测模型。采用三维Puck失效准则预测层内纤维与基体的破坏,并获得基体失效时的断裂面角度。根据低速冲击下复合材料层合板的层间分层损伤机理,同时考虑面内横向正应力、厚度方向正应力、层间剪应力和相邻铺层的损伤状态等因素对界面分层的影响,发展了一种新的冲击分层失效准则。为快速有效地预测铺层总数较多的复合材料层合板的冲击损伤,通过对单元积分点处的应变进行线性插值,提出了在单个实体单元内预测多个铺层损伤的数值计算方法。模型成功预测了受冲击层合板具体的失效模式,预测的分层形状和尺寸与试验值吻合较好,并显著减少了有限元模型的规模,表明本文所发展的数值方法对预测复合材料层合板低速冲击损伤的有效性。