主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

双后掠鸭翼气动特性的数值模拟

首先针对具有中等前缘后掠角梯形鸭翼的缺点提出双后掠鸭翼概念,然后分别对安装梯形鸭翼和双后掠鸭翼的近距耦合鸭式布局的气动性能进行数值模拟研究,分析影响双后掠鸭翼气动性能的流动机理。研究表明：在大迎角时,对于双后掠鸭翼,具有较大前缘后掠角的外翼段可以使鸭翼涡在涡核破裂后仍能形成稳定集中涡并保持较高的强度,增加鸭翼本身的失速迎角,并通过诱导作用改善机翼外翼段流场,进而提高全机大迎角性能,但在小迎角时会破坏鸭翼附着流或前缘气泡涡的发展,造成略微的升力损失。拥有较大失速迎角的双后掠鸭翼在小迎角时具有较大的可用偏度,可以增强布局的抬头控制能力。双后掠鸭翼在满足隐身约束的前提下,超声速阻力较小,具有较好的超声速性能。     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski(M–K) model is widely used to predict material’s forming limit curve(FLC).The prediction of FLC traditionally neglected through-thickness normal stress.However, it cannot be neglected in some forming processes.Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress.In addition, based on Nakazima test process, the ratio o...     

静子叶栅安装角异常非定常流场数值研究

为了研究静子叶栅安装角异常对叶栅通道流场的影响,利用商业软件NUMECA对二维叶栅某个叶片安装角增加5°不同攻角进行非定常流场数值模拟,得到了因安装角异常导致叶栅通道堵塞时对叶栅通道内的流场结构及叶片载荷的影响。结果表明,安装角调节5°时,在正攻角下,随着攻角的增大叶栅通道内流动不断恶化,吸力面出现大面积的附面层分离;负攻角时,气流比较平稳,但是漩涡脱落频率高达3500Hz。分析发现,安装角异常时攻角对漩涡尺度和脱落频率影响较大,其中叶片动态气动力脉动量迅速增大,可能是导致发动机叶片疲劳破坏的原因之一。     

变弯度导叶对某高负荷双级风扇气动性能的影响

为了改善某高负荷双级风扇在非设计转速出现的裕度不足和转子攻角过大的问题,研究了变弯度导叶的调节对高负荷双级风扇气动性能和内部流场的影响,对比分析了不同形式变弯度导叶和传统可调导叶的性能差异.数值模拟结果表明:80%转速时高负荷双级风扇的绝热效率随着正预旋角度增加而显著增加,预旋角度为30°时的绝热效率提高了3.5%;传统可调导叶扩稳效果较优,受到大预旋角度下大损失的限制;变弯度导叶的开缝形式、开缝位置、导叶稠度均与气动性能密切相关,具体设计需要根据高负荷双级风扇工作情况进行探讨.      

空投鱼雷蛇形搜索攻击有利提前角模型研究

提出了一种用等效扇面方法对蛇形搜索航行鱼雷攻击有利提前角的解算方法,并通过仿真对模型进行了修正。仿真结果表明,经修正后的鱼雷可达到最大命中概率。     

Kinetic Monte Carlo Simulation of EB-PVD Film:Effects of Substrate Temperature

The 2D kinetic Monte Carlo (KMC) simulation was used to study the effects of different substrate temperatures on the microstruc-ture of Ni-Cr films in the process of deposition by the electron beam physical vapor deposition (EB-PVD). In the KMC model, substrate was assumed to be a “surface” of tight-packed rows, and the simulation includes two phenomena: adatom-surface collision and adatom diffusion. While the interaction between atoms was described by the embedded atom method, the jumping energy was calculated by the molecular static (MS) calculation. The initial location of the adatom was defined by the Momentum Scheme. The results reveal that there exists a critical substrate temperature which means that the lowest packing density and the highest surface roughness structure will be achieved when the temperature is lower than the smaller critical value, while the roughness of both surfaces and the void contents keep decreasing with the substrate temperature increasing until it reaches the higher critical value. The results also indicate that the critical substrate temperature rises as the deposition rate increases.     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

How do interplanetary shock impact angles control the size of the geoeffective magnetosphere?

In this paper, we investigate temporal and spatial magnetosphere response to the impact of interplanetary (IP) shocks with different inclinations and speeds on the Earth’s magnetosphere. A data set with more than 500 IP shocks is used to identify positive sudden impulse (SI⁺) events as expressed by the SuperMAG partial ring current index. The SI⁺ rise time (RT), defined as the time interval between compression onset and maximum SI⁺ signature, is obtained for each event. We use RT and a model suggested by Takeuchi et al. (2002) to calculate the geoeffective magnetospheric distance (GMD) in the shock propagation direction as a function of shock impact angle and speed for each event. GMD is a generalization of the geoeffective magnetosphere length (GML) suggested by Takeuchi et al. (2002), defined from the subsolar point along the X line toward the tail. We estimate statistical GMD and GML values which are then reported for the first time. We also show that, similarly to well-known results for RT, the highest correlation coefficient for the GMD and impact angle is found for shocks with high speeds and small impact angles, and the faster and more frontal the shock, the smaller the GMD. This result indicates that the magnetospheric response depends heavily on shock impact angle. With these results, we argue that the prediction and forecasting of space weather events, such as those caused by coronal mass ejections, will not be accurately accomplished if the disturbances’ angles of impact are not considered as an important parameter within model and observation scheme capabilities.     

飞行器航迹倾角的自适应动态面控制

针对飞行器纵向模型具有参数不确定性和外界干扰的特点,提出一种飞行器航迹倾角的自适应动态面控制方法.动态面控制方法通过引入一阶低通滤波器避免了传统反演设计存在的"微分爆炸"现象,采用自适应律对模型未知参数进行在线估计,并利用非线性阻尼项克服外界干扰.通过Lyapunov方法证明得出闭环系统半全局一致稳定,跟踪误差可通过调节控制器参数达到任意小.仿真结果表明:该方法能在简化控制设计过程的同时保证航迹倾角跟踪上预定轨迹,控制系统具有较强的自适应能力且对外界干扰具有一定的鲁棒性.