垂准仪校准的一个新方法

介绍了一种溯源于重力线的垂准仪校准方法;分析了＂顶杆式铅垂准线＂与＂平行光管式水平准线＂之间的联系与区别;基于顶杆式铅垂准线校准的几何模型,给出了天顶/底角的计算方法。     

帆板控制系统设计

该帆板控制系统采用塑料薄膜电位器作为传感器检测角度信号,检测到的角度信号经信号处理电路送12位的串行接口A/D转换器ADS7818进行数字化转换,转化结果由Cortex-M3处理器LM3S615进行处理产生PWM控制信号,该控制信号经功率VMOS驱动电路实现轴流电扇的速度调节,从而实现帆板角度定位闭环控制。通过按键可以实现帆板角度的设定及运行控制,设置六位LED数码管显示实现角度及其它运行状态的显示。经过实际测试该系统完全达到了设计要求的各项指标要求。     

某型教练机机载天线与雷达罩的射线入射角的计算

随着现代高科技的发展,雷达大量应用于飞机、导弹、航海等领域．雷达罩的运用也日趋广泛。本文通过曲线拟合等一些数学分析方法,运用MATLAB工具,经过分析、编程、计算．最后得到机载天线与雷达罩的射线入射角,通过入射角的大小可判断此雷达罩是否符合要求。     

拖靶系统挂机安装角度计算

拖靶安全释放是拖靶系统正常执行任务的前提,拖靶挂机安装角度的优劣直接影响着拖靶的安全释放.依据拖靶释放特性建立了拖靶系统动力学模型,提出了拖靶安全释放的条件,给出了拖靶挂机安装角度的计算方法;通过实例对方法的正确性进行了验证,其结果直接应用于某新型拖机改装试验中,取得了满意的效果.     

螺旋桨飞机起飞构型突风影响研究

对于小迎角纵向静不稳定飞机,突风给飞机带来显著的安全隐患,为此,结合飞行品质规范中的突风模型,给出不同概率和不同高度下的突风速度。针对某螺旋桨飞机,计算分析垂直向上和向下突风所引起的飞机迎角变化,获得了起飞状态下可行的飞行速度和高度范围。研究结果表明,垂直向下突风显著地削弱了该类飞机的纵向静稳定性;垂直向上突风显著地减小了其安全迎角裕度。     

突片作用下气膜冷却效率的试验研究

为了研究突片对气膜冷却的影响规律, 设计了3种不同堵塞比的等边三角形突片, 并对其对气膜冷却特性的影响规律进行了实验研究.研究结果表明, 与无突片的气膜冷却相比, 突片的存在提高了气膜冷却效果;冷却效率随吹风比的增加而增大, 且沿气流方向冷却效率存在一极大值;当吹风比M<1.5时, 冷却效率随吹风比的增加而增大;当M>1.5时, 冷却效率随吹风比的增加而减小.      

基于伴随非等温射流理论的缝槽气膜冷却模型

在伴随非等温射流基础上发展了一种适用于缝槽气膜冷却绝热温比预估的数学模型.通过合理假设推导出二维壁面射流混合层核心温度分布规律,将其作为气膜绝热壁温,并考虑缝槽几何特征参数和气膜吹风比对冷却效率的影响,得到绝热温比计算公式.用试验数据对该预估模型进行拟合分析,得到了与试验数据拟合精度在±8%以内的半经验预估模型,证明该模型的可行性和应用潜力,并需要更多的试验数据对其进行验证和改进.      

空投鱼雷蛇形搜索攻击有利提前角模型研究

提出了一种用等效扇面方法对蛇形搜索航行鱼雷攻击有利提前角的解算方法,并通过仿真对模型进行了修正。仿真结果表明,经修正后的鱼雷可达到最大命中概率。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.