应用加权中值滤波法检测薄壁梁式挠性器件下摆量

应用加权中值滤波法对薄壁梁式挠性器件下摆量进行高准确度CCD检测。薄壁梁式挠性器件在测量过程中测量图像存在高频抖动现象,因此测量准确度不高,运用加权中值滤波后使用最小二乘法细分技术,可以在实现提高测量准确度的同时,消除高频抖动带来的误差,从而可以有效提高CCD测量薄壁梁式挠性器件下摆量的准确度。实验表明,该方法比传统测量方法准确度提高20倍以上。     

航空维修人为差错理论分类和对比研究

通过对航空维修人为差错理论的梳理和比较，将航空界已形成的主要人为差错理论分成三类：个人学派、组织学派和系统学派．并对各理论的研究视角、特点、优点和局限性进行了归纳和对比。     

平台摇摆对卡尔曼滤波跟踪精度的影响

通过建立目标相对运动坐标系和目标相对运动观测模型,研究了在平台摇摆影响下,跟踪系统观测到的目标运动状态的变化。在分析捷联垂直基准补偿原理的基础上建立了捷联垂直基准平台摇摆角补偿模型,建立的模型结合捷联垂直基准系统的测量能力对其补偿算法进行了理论推导,使模型适用于实际捷联垂直基准系统。通过建立模型以及仿真研究了平台摇摆作用下卡尔曼滤波跟踪精度的变化,指出了摆造成卡尔曼滤波跟踪精度降低甚至离散的主要原因在于模型误差增大。设计仿真实验验证了结论的正确性,为进一步改进跟踪手段提供了理论参考。     

Hybrid integration method for highly maneuvering radar target detection based on a Markov motion model

To detect highly maneuvering radar targets in low signal-to-noise ratio conditions, a hybrid long-time integration method is proposed, which combines Radon-Fourier Transform (RFT), Dynamic Programming (DP), and Binary Integration (BI), named RFT-DP-BI. A Markov model with unified range-velocity quantification is formulated to describe the maneuvering target’s motion. Based on this model, long-time hybrid integration is performed. Firstly, the whole integration time is divided into multiple time segments and coherent integration is performed in each segment via RFT. Secondly, non-coherent integration is performed in all segments via DP. Thirdly, 2/4 binary integration is performed to further improve the detection performance. Finally, the detection results are exported together with target range and velocity trajectories. The proposed method can perform the long-time integration of highly maneuvering targets with arbitrary forms of motion. Additionally, it has a low computational cost that is linear to the integration time. Both simulated and real radar data demonstrate that it offers good detection and estimation performances.     

双框架飞机蒙皮检测机器人切换运动控制方法

针对一种双框架飞机蒙皮检测机器人,通过分析该机器人在飞机表面上的受力情况,在飞机表面该机器人受到了非完整约束,基于牛顿-欧拉法建立了机器人非完整约束动力学模型。根据机器人机械结构和运动步态分析,将该非完整机器人系统分为子系统A和子系统B。为了实现机器人在飞机表面运动,采用反演技术和快速Terminal滑模控制相结合的思想对系统设计了控制器,提出了一种反演-滑模控制方法;对于非完整机器人子系统A和子系统B,设计了一种基于事件驱动的切换策略,实现了机器人对期望轨迹的全局渐近跟踪,并利用Lyapunov稳定性证明系统的跟踪误差收敛。仿真和试验表明,采用该切换策略和反演-滑模控制方法,双框架飞机蒙皮检测机器人可以在飞机表面自由运动并进行损伤检测,具有良好的可靠性和稳定性。     

微分法在定位误差分析与计算中的应用

介绍了微分法分析计算定位误差的原理和适用范围,通过生产实例分析,证明了该方法在解决多误差因素定位误差分析与计算中的简便与快捷,从而有效简化了复杂定位方案定位误差的分析与计算,提高了夹具的设计效率。     

Multi-mode diagnosis of a gas turbine engine using an adaptive neuro-fuzzy system

Gas Turbine Engines (GTEs) are vastly used for generation of mechanical power in a wide range of applications from airplane propulsion systems to stationary power plants. The gas-path components of a GTE are exposed to harsh operating and ambient conditions, leading to several degradation mechanisms. Because GTE components are mostly inaccessible for direct measurements and their degradation levels must be inferred from the measurements of accessible parameters, it is a challenge to acquire reliable information on the degradation conditions of the parts in different fault modes. In this work, a data-driven fault detection and degradation estimation scheme is developed for GTE diagnostics based on an Adaptive Neuro-Fuzzy Inference System (ANFIS). To verify the performance and accuracy of the developed diagnostic framework on GTE data, an ensemble of measurable gas path parameters has been generated by a high-fidelity GTE model under (a) diverse ambient conditions and control settings, (b) every possible combination of degradation symptoms, and (c) a broad range of signal to noise ratios. The results prove the competency of the developed framework in fault diagnostics and reveal the sensitivity of diagnostic results to measurement noise for different degradation symptoms.     

硅半球深腔结构无损检测技术

半球深腔的加工质量是决定硅基MEMS半球陀螺精度的关键因素之一，及时检测半球深腔的形貌参数并将其反馈至加工过程，是确保高性能MEMS半球陀螺研制成功的重要措施。由于硅半球深腔的深度较大，台阶仪和光学显微成像系统无法对半球深腔的形貌特征进行有效测量。因此,需要将硅深腔结构剖开后采用扫描电镜(SEM)进行检测。这种检测方式时间周期长，且属于破坏性的样本检测，效率和测试精度都较低。提出以硅半球深腔为模具，利用PDMS铸模将硅半球深腔的结构尺寸和表面形貌转移到PDMS凸起的半球模型上，通过检测PDMS半球模型的尺寸结构和表面形貌，即可反推出硅半球深腔的尺寸特征。经实验验证，脱模后的PDMS模型可以准确地反映出半球深腔的尺寸信息，测量结果的不确定度小于5‰，有效解决了硅半球深腔无损检测的难题。     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.