基于晶体塑性理论的疲劳裂纹起始数值模拟

在疲劳荷载作用早期,材料在晶体尺度出现裂纹的萌生,为了研究疲劳短裂纹的发展,利用Monte Carlo法建立了多晶体晶粒集合的Voronoi有限元模型,并在Ansys Usermat子程序接口下编写了晶体塑性本构方程子程序,修正了以拉伸硬化为主的疲劳裂纹起裂的计算机模拟方法,并结合TANAKA和MURA的位错偶极子模型,模拟了晶粒集合在疲劳荷载作用下的裂纹萌生,最后与文献实验数据对比,这一修正的方法更加符合实验结果和宏观现象.     

基于Fibonacci搜索方法的航空发动机性能寻优

介绍了Fibonacci搜索方法应用于发动机性能优化中的原理,建立带两个出口面积、气流马赫数可变的引射器的涡喷发动机的总体性能计算模型,应用Fibonacci搜索方法在优化参数区间内对该发动机进行了最大推力、最低油耗、最低涡轮前温度模式的寻优.举例说明了Fibonacci搜索方法应用的具体过程.给出了不同高度、马赫数下的寻优结果.结果表明:最优目标性能满足的约束边界与飞行高度、马赫数密切相关.不同的飞行高度、马赫数对应了不同的最优控制策略.但不论飞行任务如何,根据该方法进行的优化控制所获得的目标性能是最佳的.该优化方法不仅适用于该类涡喷发动机,也为其他类型航空发动机的优化控制打下一定的基础.      

Advances and trends in plastic forming technologies for welded tubes

With the implementation of environmental protection, sustainable development and conservation-oriented policies, components and parts of thin-walled welded tubes have gained increasing application in the aircraft and automotive industries because of their advantages: easily achieving forming and manufacturing process at low cost and in a short time. The current research on welded tube plastic forming is mainly concentrated on tube internal high-pressure forming, tube bending forming, and tube spinning forming. The focuses are on the material properties and characterization of welded tubes, finite element modeling for welded tube forming, and inhomogeneous deformation behavior and the mechanism and rules of deformation coordination in welded tube plastic forming. This paper summarizes the research progress in welded tube plastic forming from these aspects. Finally, with a focus on the urgent demand of the aviation, aerospace and automotive industries for high-strength and light-weight tubes, this paper discusses the development trends and challenges in the theory and technology of welded tube plastic forming in the future. Among them,laser tailor-welded technology will find application in the manufacture of high-strength steel tubes.Tube-end forming technology, such as tube flaring and flanging technology, will expand its application in welded tubes. Therefore, future studies will focus on the FE modeling regarding how to consider effects of welding on residual stresses, welding distortions and microstructure, the inhomogeneous deformation and coordination mechanism of the plastic forming process of tailor-welded tubes, and some end-forming processes of welded tubes, and more comprehensive research on the forming mechanism and limit of welded tubes.     

金属弹簧管性能影响因素的仿真分析

为了研究高温密封组件金属弹簧性能,本文通过对波音公司编网状弹簧管结构和Streck心脏支架结构的研究,建立了编织弹簧的几何拓扑构型和数学模型,推导了弹簧直径计算公式。采用AUTODESK3D-MAX构建了编织弹簧的仿真模型,用ANSYS仿真软件分别从编织丝直径、编织密度以及编织方法 3方面探究不同测试对弹簧性能的影响。结果表明,增加弹簧丝直径、降低弹簧管轴向方向的编织密度、提高圆周方向的编织密度、向外的弹簧管编织方式可有效提高弹簧管的回弹性能。     

基于离散粒子群算法的航空发动机总装工艺优化方法

为了提高航空发动机总装工作的效率与质量,加强对总装工序和总装机件的管控,量化不同总装人员工作任务量,提高发动机总装的一致性和可追溯性,提出了1种发动机总装分区优化方法。以改进的2进制粒子群算法为基础,平衡了发动机总装各区域的工作内容,最小化各总装区域的工作差异,增强了每个区域装配机件的关联度,提高了总装工作的并行度,从而提高了装配质量。以某型发动机总装区域划分工作为实例,通过上述算法进行了总装区域划分,量化了所有装配区域每一工序的具体装配内容,减小了不同装配区域间的机件差异,杜绝了缺件、剩件等装配问题。     

带非线性支撑的转子有限元模型求解方法

用数值方法研究了非线性支撑的柔性转子系统的动学行为,提出了一种将有限元与非线性支撑结合的模型和求解方法。利用有限元法(FEM)构建转轴和转盘部分的模型,通过矩阵进行组合;利用离散元方法对包含滚动轴承和挤压油膜阻尼器(SFD)的支撑部分进行建模,此部分包含4个单元,分别为轴承内圈、外圈、SFD内圈和支撑鼠笼。有限元部分和离散元部分通过轴端节点相连,仿真过程中轴端位移传递给非线性支撑部分,支撑部分通过位移计算得到的非线性力反过来作用于有限元转子轴端部分。为了耦合求解有限元转子和非线性支撑组成的数学模型,提出了一种综合的迭代求解方法,克服传统的有限元求解方法对轴端隐性非线性支撑的求解局限性。由于转轴部分采用了Timoshenko梁单元建模,对比与简单转子模型,可以考虑陀螺力矩和轴的柔性特征,更能体现非线性支撑对振动真实影响。在建立的20个轴单元的有限元转子模型中,非线性响应更多体现在靠近非线性支撑的节点1和节点21处,响应频谱中靠近轴端的节点能体现出滚动轴承的2倍和3倍变柔振动频率。     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

基于拓扑优化和形状优化的桨叶结构设计

直升机旋翼桨叶剖面结构设计是研究旋翼动力学设计的基础。提出一种联合拓扑优化和形状优化的 两级优化设计方法,可用于桨叶剖面结构的设计。第一级优化以变密度法(SIMP)作为拓扑优化的材料插值方 法,以桨叶体积最小化为设计目标,约束桨叶节点位移和应力,建立桨叶的拓扑优化求解模型;第二级优化以重 构的桨叶模型为基础开展形状优化,降低局部应力集中以及找到合理的边界节点位置。对优化后的模型进行 有限元分析,结果表明:通过拓扑优化和形状优化的两级优化,能够得到满足强度和稳定性要求的结构布局,为 桨叶结构设计提供指导方案。     

基于有限元的超精密空气静压主轴最佳综合刚度设计

超精密空气主轴的刚度是超精密主轴的一个非常重要的指标,轴承的结构形式、气膜结构参数均对刚度指标有影响.本文通过工程计算得到气膜刚度等参数后,在特定空间尺寸和重量的限制条件下,基于有限元进行Nanosys-600F五轴超精密机床的气浮主轴(C轴)机械结构设计,通过多次分析,得到了气浮主轴(C轴)最佳综合刚度结构参数.     

A review of topology optimization for additive manufacturing: Status and challenges

Topology optimization was developed as an advanced structural design methodology to generate innovative lightweight and high-performance configurations that are difficult to obtain with conventional ideas. Additive manufacturing is an advanced manufacturing technique building as-designed structures via layer-by-layer joining material, providing an alternative pattern for complex components. The integration of topology optimization and additive manufacturing can make the most of their advantages and potentials, and has wide application prospects in modern manufacturing. This article reviews the main content and applications of the research on the integration of topology optimization and additive manufacturing in recent years, including multi-scale or hierarchical structural optimization design and topology optimization considering additive manufacturing constraints. Meanwhile, some challenges of structural design approaches for additive manufacturing are discussed, such as the performance characterization and scale effects of additively manufactured lattice structures, the anisotropy and fatigue performance of additively manufactured material, and additively manufactured functionally graded material issues, etc. It is shown that in the research of topology optimization for additive manufacturing, the integration of material, structure, process and performance is important to pursue high-performance, multi-functional and lightweight production. This article provides a reference for further related research and aerospace applications.