弓激波前内透射离子动力学横场流静电不稳定性

本文讨论了地球弓激波前内背景电子速度分布函数为平顶形式时的透射离子横场流静电不稳定性.结果表明,在超临界(Alfvén Mach数M_A>3)准垂直激波区(激波法向与行星际磁场之间的夹角75°)情况下,透射离子流产生的静电不稳定性增长率峰值要比电子速度为Maxwell分布时更加显著,并满足动力学性质.     

加气喷嘴气体注入形式对雾化性能的影响

本文用马尔文粒度分析仪测量喷雾的平均液滴尺寸及液滴尺寸分布,研究了气体注入形式对喷雾特性的影响.喷嘴压降为34.5～690kPa,喷嘴气液比为0.002～0.023.试验中使用了两种气体注入形式:一种是直径6.3mm的单孔,另一种是20个直径0.5mm的小孔.它们与三种不同孔径的喷孔配合使用.其孔径分别为0.8,1.6和2.4mm.研究结果表明,雾化质量主要取决于喷嘴压降和气液比,而对气体注入形式和喷孔直径不敏感.测量液体流量看出,此类喷嘴的流量系数很小.雾化液体中含有固体颗粒或其它易堵塞小孔或喷嘴通道的有害物时,使用这种喷嘴将会显示出它的优点.     

高分散高稳定ZrO2水悬浮液的分散性研究

本文选用纳米粉ZrO2,分别采用单一静电稳定机制、加入PEG的空间位阻稳定机制和加入PMAA-NH4的电空间稳定机制制备成2vol%的ZrO2水悬浮液,通过Zeta电位、沉降实验等手段,最终得到了碱性条件下的高分散、高稳定的ZrO2水悬浮液。实验证明:当pH=8.3时,PMAA-NH4的分散效果最好。     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

自制等离子喷枪冷却系统的设计及测试

等离子喷枪是制备热障涂层中的研究重点。目前关于等离子喷枪的研究多集中于喷嘴(阳极)、阴极,鲜有关于喷枪冷却系统方面的研究;喷枪冷却系统的优劣直接影响喷枪的工作寿命和喷涂过程的稳定性,同时制备热障涂层的质量也与冷却效果紧密相关。本文利用三维模型,详细阐述了自制的喷枪冷却系统通道及工作原理,并对设计进行了理论计算,对自制的喷枪进行点火试验和喷涂测试,结果显示自制的喷枪冷却系统功能良好,喷枪工作稳定,涂层质量较好。     

基于ALE法的水陆两栖飞机船体着水性能分析

水陆两栖飞机的着水性能是体现其综合性能的重要因素之一.应用ALE法对三种水陆两栖飞机船体截面进行入水仿真计算,从着水载荷、喷溅性能及运动响应三个方面对着水性能进行综合评估.对比分析了直线型、带舭弯弧形、复合型三种构型截面在不同速度、不同重量下的压力分布、喷溅性能以及运动响应,得到了三种截面横向压力分布规律.计算结果显示相同状态下,喷溅性能复合型优于带舭弯弧形、带舭弯弧形优于直线型;过载复合型远大于带舭弯弧形,带舭弯弧形稍大于直线型,综合看来带舭弯弧形截面着水性能最佳.     

Corrosion mechanism investigation of TiN/Ti coating and TC4 alloy for aircraft compressor application

It is imperative to develop multifunctional erosion and corrosion resistant coatings for compressor blades of aircraft engines in harsh environment. PVD (Physical Vapor Deposition) technology has the advances in processing erosion-resistant coatings; however, the performance of PVD coatings to combat corrosion depends on various coating defects. Determining and comparing the corrosion performances of PVD TiN/Ti coating and uncoated TC4 alloy was the main objective of present work. The 960 h salt spray corrosion and 116 h hot corrosion tests were conducted to simulate the grounding and working environments of the aircraft compressors. The corrosion mechanisms due to the coating defects such as pinhole, columnar boundary and large grain were analyzed based on the OM, Confocal microscope, electrochemical measurements, SEM, XRD and EDS results. Owing to the disordered state associated with the columnar boundary and the coating defect, nitrogen could be easily replaced by oxygen in the hot corrosion process, these structures were channels for fast diffusion of oxygen. Moreover, the Gibbs energy changes of Ti oxidation and TiN oxidation were thermodynamically calculated according to the working condition of aircraft compressors, and considerable research effort was focused on mapping out the phase diagram of Ti, TiN and high pressure gases. The findings of this research can provide insights into developing multifunctional coatings for future aircraft engines.     

针栓式喷注单元膜束撞击雾化混合过程数值模拟

为了全面认识针栓式喷注器喷雾场结构，基于自适应网格加密技术和分三相计算的PLIC VOF（Piecewise Linear Interface Calculation Volume of Fluid）方法对针栓式喷注单元膜束撞击雾化混合过程进行了仿真分析，通过对两路推进剂分别进行界面追踪，获得了膜束撞击雾化混合过程的详细结构特征，与高速摄影试验结果定性定量对比均吻合较好，验证了数值方法的准确性。以此为基础对膜束撞击的喷雾场结构、撞击变形过程、流场涡结构、雾化破碎典型特征及破碎后的雾化混合分布特征进行了识别分析，结果表明：膜束撞击形成了液束未穿透液膜和液束穿透液膜2种不同的喷雾扇结构。膜束撞击形成的喷雾扇呈"Ω"形，膜束同时发生弯曲变形和横截面变形。另外，膜束撞击同时受到正压和剪切应力作用，导致了一系列复杂涡流现象，使得相互作用增强，雾化混合均增强，这也是膜束撞击喷注构型优于膜膜撞击的本质原因。最后，还发现膜束撞击喷雾场液滴分布呈现分区结构特征，分别是液束控制主导的上雾化区、液膜控制主导的下雾化区及夹在中间的混合区，实际中应兼顾雾化特性和混合特性，选取中等动量比膜束撞击，这可为针栓式喷注器的理论研究和工程设计提供重要参考。     

热障涂层技术在航空发动机涡轮叶片上的应用

热障涂层是提高航空发动机涡轮叶片工作温度的有效途径之一。根据某型发动机高压涡轮工作叶片、导向器叶片的结构特点和各种涂层制备技术的优缺点,制定了工作叶片和导向叶片表面底层、面层和内腔的涂层制备方案。对工作叶片、导向器叶片材料试样表面涂层的性能开展一系列测试试验。结果表明:涂层性能满足要求,涂层制备方案合理可行;对工作叶片、导向器叶片内表面涂层的厚度,气膜孔径的影响以及质量增加情况进行测量分析,结果均满足设计要求,表明涂层制备工艺合理可行。     

海洋大气环境下微动开关触点回跳时间增大故障的试验复现与分析

结合某型微动开关触点回跳时间增大导致某系统故障问题,设计了由干湿交替酸性盐雾试验和湿热试验组成的海洋大气环境效应加速模拟试验剖面,选取与外场故障件型号一致的微动开关为研究对象,通过实验室加速模拟试验,成功复现了外场故障现象,并结合试验结果对腐蚀性环境、电烧蚀等因素对触点回跳时间增大的影响机制进行了分析。