基于变刚度变阻尼的柔性喷管动态模型

针对柔性接头动态迟滞曲线受控制系统控制位置精度和动态响应速度影响较大的问题,基于电液伺服机构和柔性接头变刚度变阻尼模型,构建了柔性喷管的电液伺服机构-变刚度变阻尼模型,将其和电液伺服机构-定刚度定阻尼模型进行了对比。分析了电液伺服机构主要参数、柔性接头工作参数等对电液伺服机构-柔性接头系统动态特性的影响。分析结果表明:电液伺服机构-变刚度变阻尼模型所构造的迟滞曲线可更准确地与实验结果相吻合,并符合迟滞曲线随频率变化的规律,反馈系数、放大器静态放大系数、电液伺服机构增益、滑阀流量增益等参数对系统动态特性的影响更为明显。该模型为固体火箭发动机电液伺服机构-柔性接头系统动态特性的调整提供理论依据。     

气动换向阀阀芯/阀座撞击特性研究

针对某型气动换向阀在研制过程中出现由于阀芯/阀座撞击变形导致阀芯卡死的现象,对阀芯/阀座的撞击特性进行了仿真研究,定量分析了撞击过程以及不同阀座高度对撞击特性的影响,根据仿真结果对换向阀进行了改进设计,试验结果表明改进后的换向阀满足使用要求.     

基于试验的电动舵机模型辨识

目前电动舵机模型的建立基本上是基于理论的数学推导,所建立的舵机模型与实际舵机模型存在一定的误差。针对此问题,提出一种基于试验实测数据建立舵机模型的方法,搭建自动数据采集试验平台,采用组合窗法对实测数据进行频域转换,得到舵机的频率响应函数并采用非线性最小二乘法辨识舵机模型。对辨识得到的数学仿真结果与实际舵机响应比较,在频域,整个频段内幅频特性最大绝对误差1.9 dB;在时域,仿真模型跟踪实际舵机角度的最大误差1.5°,延迟时间10 ms。结果表明,基于试验数据建立的舵机仿真模型能很好地模拟实际舵机。     

三余度数字伺服控制系统建模与动静态特性研究

对研究的三余度伺服控制系统的机理进行分析，建立了被控对象的线性化数学模型。在此基础上，对数字动压反馈环节的参数进行了仿真寻优，并对无故障和两种单点故障情况下系统的动、静态特性进行了仿真和分析。带惯性负载试验结果证实了理论建模分析的正确性，并表明数字动压反馈也能起到对负载谐振的阻尼作用，与机械式、模拟式实现形式相比，它更灵活、方便。     

Design and Application of Discrete Sliding Mode Control with RBF Network-based Switching Law

This article proposes a novel approach combining exponential-reaching-law-based equivalent control law with radial basis function (RBF) network-based switching law to strengthen the sliding mode control (SMC) tracking capacity for systems with uncertainties and disturbances. First, SMC discrete equivalent control law is designed on the basis of the nominal model of the system and the adaptive exponential reaching law, and subsequently, stability of the algorithm is analyzed. Second, RBF network is used to form the switching law in a direct and online manner with sliding-mode-related inputs and by approximating evaluation function; and the method to adjust its parameters is devised. Finally, comparable experiments are carried out to verify the application of the proposed approach to an inner-axis driven by a direct current (DC) torque motor through extra-low speed servo for a high precision flight simulator, and the axis works under deteriorating conditions such as periodically fluctuating torques of motor, nonlinear friction, and time-varying model parameters. The results show that the combined SMC can effectively improve the servo performance, for instance, to a stable 0.000 08 (°)/s speed response, the tracking error would be within 0.000 08° in 98% of operating times. Moreover, the hybrid nature of the approach imparts the RBF network the features of removing offline training and ease to set initial parameters.     

某型压差活门的动态特性分析

压差活门是航空发动机数控系统燃油计量装置中重要的液压部件,其稳定性和动态性能直接影响控制系统的整体性能。根据压差活门非线性微分方程,采用小偏差线性化方法,推导出了压差活门的动态数学模型,得到了压差活门的方框图以及传递函数。选取某压差活门参数建立了Simulink仿真模型,分别在频域和时域分析了其动态性能。结果表明:在频域上,比较了有无节流器时的回路增益函数伯德图,认为敏感油路上的节流器可以改善稳定性且提高控制精度,通过设计节流器的尺寸可以调节穿越频域,从而改善系统的动态性能;在时域上,分析了不同节流器尺寸下阶跃响应的动态性能,其试验结果与实际工程经验一致。     

变结构控制在基于脉冲比例阀的燃油调节系统中的应用

针对航空发动机燃油控制系统中二阶非定常执行机构通常出现设计困难的问题,介绍一种变结构控制方法,将二阶非定常执行机构变成确定的一阶惯性环节,该方法既充分利用其优点"不变性"又可以规避其突出缺点"抖振",特别适用于驱动脉冲比例调节阀;同时提出脉冲比例阀的变结构调节中遇到的实际问题(例如微分的精度问题)的解决办法,以及影响该方法可行性的若干必要条件。结果表明:符合条件时变结构控制在基于脉冲比例阀的燃油调节系统中是可行的。     

液压余度舵机同步传动研究

几个舵机驱动同一控制对象,通道间产生力的纷争,本文采用均衡网络来减轻力的纷争,而均衡网络的参数则根据解耦控制理论导出。实际系统的实验证明本文所提出的消除余度通道间力纷争保证同步传动的方案是有效的。文章给出了最优均衡网络的参数设计公式。     

A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

西安某粘接材料厂室内供暖、热水系统的设计

基于厂方对供热系统的要求,根据供热建筑物、机房和可利用设施的实际情况,采用一台换热器,通过阀门的切换,实现了供暖和供热水的分段运行。将蒸汽发生器的进水与系统补水有机地整合为一个系统,有效地解决了机房面积过小的实际困难。利用自来水的压力和热水箱与浴室的高差解决了热水供应的实际问题。