蜂窝填充薄壁盒式梁的约束弯曲

在刚性剖面假设的基础上分析具有蜂窝芯材薄壁盒式梁约束弯曲问题。应用分离变量法,建立并求解了两个常微分支配方程。边界条件可以精确满足,同时,解答是用本征函数展开式表达的。剪力图是由三角级数表示的,并用于决定上述本征函数展开式的待定系数。计算结果给出了蒙皮正应力与剪应力以及蜂窝芯材剪应力沿翼弦和翼展的分布规律并显示了附加应力的衰减情况。     

Deformation Behavior of Medium-strength TA18 High-pressure Tubes During NC Bending with Different Bending Radii

To improve the forming quality and forming limit of the numerical control (NC) bending of high-pressure titanium alloy tubes, in this study, using three-dimensional (3D) finite element method, deformation behavior of medium-strength TA18 high-pressure tubes during NC bending with different bending radii is investigated. The results show that the cross-sectional deformation and the wall thickness variation during NC bending of TA18 tubes using a small bending radius (less than 2 times of tube outside diameter) are clearly different from that using a normal bending radius (between 2 and 4 times of tube outside diameter). For bending with a normal bending radius, with or without a mandrel, the distribution of the flattening in the bending area resembles a platform and an asymmetric parabola, respectively. For bending with a small bending radius, with or without a mandrel, the flattening both distributes like a parabola, but the former has a stable peak which deflects toward the initial bending section, and the latter has a more pronounced peak with a bending angle and deflects slightly toward the bending section. The wall thickness variations with a normal bending radius, with and without a mandrel, both resemble a platform when the bending angle exceeds a certain angle. For the bending with a small radius, the distribution of the wall thickness variation without a mandrel follows an approximate parabola which increases in value as the bending angle increases. If a mandrel is used, the thickening ratio increases from the initial bending section to the bending section.     

瞄准吊舱捷联惯导系统快速传递对准方法

 新型瞄准吊舱系统中安装捷联惯导系统,使其在跟踪、探测目标的同时具备一定的自主导航能力。吊舱系统中的捷联惯导一般采用较低精度的惯性器件配置,且传递对准实现过程受到机动条件的严格限制。针对该问题提出了一种“比力积分/角速度匹配”传递对准方法,利用主惯导导航信息与惯性器件输出,以及子惯导惯性器件输出实现子惯导的对准。推导了基于主、子惯导系统误差的数学模型,详细分析了器件精度与低动态条件对系统状态量可观测度的影响,并针对低精度惯性器件与低动态条件下的传递对准性能进行了数字仿真。仿真结果表明,该方法在器件低精度与低动态条件下,对准性能达到5′,优于常规传递对准方法,可满足瞄准吊舱捷联惯导系统的快速对准性能要求。     

A Study on Multi-defect Constrained Bendability of Thin-walled Tube NC Bending Under Different Clearance

Thin-walled tube numerical control (NC) bending is a tri-nonlinear physical process with multi-defect and multi-die constraints. The clearance on each contact interface is the major factor to indicate the contact conditions. A three-dimensional-finite element (3D-FE) model is established to consider the realistic dynamic boundary conditions of multiple dies under ABAQUS/Explicit platform. Combined with experiment, numerical study on bending behavior and bendability under different clearance between tube and various dies is conducted in terms of wrinkling, wall thinning and cross section deformation. The results show that (1)with smaller clearance of tube-wiper die and tube-mandrel, the wrinkling can be restrained while the wall thinning It and cross-section deformation Id increase; while excessive small clearance blocks tube materials to flow past tangent point and causes piles up, the onset of wrinkling enhances It and Id. (2)Both It and Id decrease with smaller clearance of tube-pressure die; the wrinkling possibility rises with larger clearance on this interface if the mandrel’s freedom along Y-axis is opened; smaller clearance of tube-bend die prevents wrinkling while increases It, and the clearance on this interface has little effect on Id. (3)A modified Yoshida buckling test (YBT) is used to address the wrinkling mechanisms under normal constraints in tube bending: the smaller clearance may restrain wrinkling efficiently; the smaller wall thickness, the less critical clearance needed; the critical clearance for tube bending 38 mm×1 mm×57 mm (tube outer diameter×wall thickness×centerline bending radius) equals about 20% of initial wall thickness.     

Forming Characteristics of Al-alloy Large-diameter Thin-walled Tubes in NC-bending Under Axial Compressive Loads

Tube thinning control without wrinkling occurring is a key problem urgently to be solved for improving the forming qualities in numerical control (NC) bending processes of large-diameter Al-alloy thin-walled tubes (AATTs). It may be a way solving this problem to exert axial compression loads (ACL) on the tube end in the bending. Thus, this article establishes a three-dimensional (3D) elastic-plastic explicit finite element (FE) model for the bending under ACL and has its reliability verified. Through a multi-index orthogonal experiment design, a combination of process parameters, each expressed by a proper range, for this FE model is derived to overcome the compression instability on tube ends. By combining the FE model with a wrinkling energy prediction model, an in-depth study is conducted on the forming characteristics of large-diameter AATTs with small bending radii and it can be concluded that (1) The larger the tube diameters and the smaller the bending radii, the larger the induced tangent tension stress zones on tube intrados, by which the tube maximum tangent compression stress zones will be partitioned in the bending processes; thus, the smaller the ACL roles in decreasing thinning degrees and the larger the compression instability possibilities on tube ends. (2) The tube wrinkling possibilities under ACL are larger than without ACL acting in the earlier forming periods, and smaller in the later ones. (3) For the tubes with a size factor less than 80, the ACL roles in decreasing thinning degrees are stronger than in increasing wrinkling possibilities.     

机动飞行飞行器内具有初始弯曲和刚度不对称的转子运动模型

本文建立了位于机动飞行飞行器内且同时具有初始弯曲、不对称刚度和质量不平衡的单盘Jeffcott转子的动力学模型。当飞行器静止时,设相关参数为零后该模型与相应地面转子系统的数学模型完全相同。应用该模型可数值仿真研究飞行器运动时位于飞行器内的等转速、等加速、等减速运行转子的动态特性,研究飞行器不同飞行速度和加速度对转子动力学特性的影响,分析飞行器飞行时转子出现故障时的响应特性,从而为机动飞行器内转子的动力学分析和故障诊断提供依据。     

闭截面型材的拉弯成形性

拉弯是型材的基本成形方法.截面畸变是型材拉弯成形中的常见缺陷,并对型材的回弹和变薄有交叉影响,型材拉弯成形性的分析评估远比板材成形复杂.提出了型材拉弯成形性的概念,建立了矩形截面型材拉弯成形性分析模型,基于有限元数值模拟研究了截面结构、相对高度和壁厚分布等几何参数对拉弯成形性的影响规律,从提高拉弯成形性出发提出了型材截面优化设计的原则.      

薄膜充气梁失稳载荷研究

针对薄膜充气梁在弯曲载荷下的失稳载荷问题,进行了理论及试验研究,得到充气模型失稳载荷的理论值和试验值,两者对比显示试验值高于理论值1.56倍以上,为在使用过程中充分利用充气模型的承载能力提供了有效的数据。     

弹性薄板弯曲的有限元分析法

弹性薄板弯曲是我们在制造过程中遇到的最常见的问题,为使问题简单化,便于理解,我们用有限元法分析薄析问题,用薄板的单元组成来取代原来的薄板,通常采用本角形和矩形薄板单元的组合代替壳体,由平面应力和弯曲应力状态加以组合得到薄板的应力状态。采用三角形单元,并将每一单元作为相应的平面应力单元和薄板弯曲单元的线性组合,介绍此类薄板弯曲问题的有限元法。     

关于圆轴含有弯弯组合的合成弯矩图形状的讨论

本文结合弯弯扭组合变形的例题，利用相关数学知识，证明了圆轴含有弯弯组合的合成弯矩图如果出现曲线，则该曲线必是(上)凹的。