液压泵污染寿命预测技术研究

利用污染敏感度建模理论,建立液压泵污染敏感度分析模型.采用污染敏感系数来描述液压泵的污染耐受程度.结合实际情况推导得到液压泵的污染寿命预测公式,并对某型定量液压泵进行了寿命预测.绘制出液压泵污染耐受曲线,为液压泵的设计和系统构建提供了有效的依据.     

功能梯度压电材料层状结构中的SH波

基于线性压电弹性理论,利用传递矩阵法,分析了功能梯度压电材料层状结构中的SH波传播特性,研究了压电梯度覆盖层中初始应力对SH波传播的影响。压电覆盖层的材料性能如弹性、压电、介电系数和密度沿厚度方向呈梯度变化。数值分析结果表明,适当的材料梯度分布,可使SH波倾向于沿覆盖层表面传播,由此能够获得更好的机电耦合性能;同时,初始应力使得波传播的相速度减小,但增大了机电耦合系数。文中的分析方法和结论,对固体火箭发动机超声探伤及其压电类传感器的研制和选择有一定的参考意义。     

基于Ansys Fluent的近场翼尖涡数值模拟与分析

为了进一步研究飞机远场尾涡,提供网格分配及湍流模型的参考,并为整机模拟提供必要的参考依据,通过基于Ansys Fluent的数值模拟方法,研究了NACA0012机翼的近场翼尖涡流场,采用有限体积法求解不可压缩雷诺平均Navier-Stokes方程,其中雷诺应力项分别以S-A和Realizable k-ε模型封闭,模拟了近场翼尖涡卷起的过程,分析了机翼表面压力以及涡核参数,包括轴向涡量、涡核位置、涡核粘性等,并与风洞实验结果进行了对比。结果分析表明:基于局部O-网的六面体网格,RKE模型要优于S-A模型,与实验值更为吻合。     

激光击穿不同气体的激光推进实验研究

为了研究激光击穿气体工质的机理,通过测量冲量耦合系数,比较了激光在不同压强下击穿不同惰性单原子气体(氩气、氦气)的效果,试验结果表明:原子序数较大的无机气体原子可以电离出更多的电子,从而击穿阈值更低,激光能量转化为爆轰波能量的能量转化效率更高,冲量耦合系数就越大,同样条件下更容易击穿。推进剂气体不同,冲量耦合系数差别较大。测量摆角对结果的影响也较大。     

平行平板内连续布置肋块流场与传热的数值模拟

为了研究平行平板内连续布置8个肋块的流场结构和传热现象, 利用计算流体力学软件FLU-ENT6.2内置的标准k-ε湍流模型、RNGk-ε湍流模型和Realizablek-ε湍流模型对此进行了数值模拟并对结果作了比较.流场结果显示在相同来流条件下, 由Realizablek-ε模型预测的肋块间逆时针方向回流区最大, 标准k-ε模型最小.数值结果表明从第2个肋块开始加热段表面压力系数Cp和努塞尔数Nu开始呈周期性变化.同时将第7个肋表面的努塞尔数数值解与实验值进行了比较, 结果为三种湍流模型都能准确模拟出努塞尔数的变化趋势.计算结果可为工程设计和使用提供参考.      

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

基于五阶自由曲面垂轴偏移的空间相机变焦方法

变焦光学系统在空间探测领域中有着重要的应用需求,提出了一种基于五阶自由曲面垂轴偏移的变焦方法,实现了具有两倍变焦能力的光学系统模型。分析了五阶自由曲面透镜的变焦原理和像差模型,采用两组五阶自由曲面透镜设计并搭建了伽利略望远系统,通过控制五阶自由曲面透镜的垂轴偏移量,来改变透镜的光焦度。仿真结果分析表明：该方法的变焦曲线具有单调性,且垂轴偏移量在8mm 以内。与传统变焦方法相比,该变焦方法的特点是结构紧凑、变焦连续、控制方法简单,避免了大幅轴向变焦运动,对于可见光、红外空间光学相机轻小型化具有重要的应用价值。     

基于行波与模态的混合方法对Timoshenko梁进行振动主动控制

 基于Timoshenko梁理论,采用波控制和独立模态空间混合方法,对悬臂梁的振动控制问题进行研究。采用波控制方法实现对Timoshenko梁结构的一点或多点的横向位移的振动控制。首先,基于结构的整体运动,采用模态坐标控制方法,对结构振动进行整体控制设计。而后,基于结构的局部性质,采用波方法吸收结构振动中的高频能量并求出Timoshenko梁中波的反射因数和透射因数。理论上研究了单位力扰动下的悬臂梁的振动。考虑的具体方法是将PD反馈波控制与基于极点配置法设计的模态控制相结合。最后给出数值结果。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

New Cutting Force Modeling Approach for Flat End Mill

A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions.