Electrochemical micromachining of microgroove arrays on phosphor bronze surface for improving the tribological performance

A high friction coefficient and a low wear rate of contacted surfaces are essential elements to friction pairs between the stator and the rotor in ultrasonic motors. It has been shown that surface textures have a significant effect on improving the tribological performance of friction pairs.In this paper, microgroove arrays are introduced to the stator surface for improving the tribological performance of friction pairs between the stator and the rotor in ultrasonic motors. Microgrooves were fabricated on a phosphor bronze surface by through-mask electrochemical micromachining(TMEMM). Parameters, namely, the electrolyte inlet pressure, applied voltage, pulse duty cycle,and frequency, were varied to investigate their influences on the dimensions and morphology of the microgrooves. Results showed that the width and depth of the microgrooves were strongly affected by the applied voltage and frequency, while the morphology of the microgrooves was dependent on the electrolyte inlet pressure and the pulse duty cycle. Compared with a smooth surface, the friction coefficient increased from 0.245 to 0.334 and less abrasion was obtained when a surface was textured with microgrooves of which the width and depth were 185.6 and 57.6 lm,respectively. Microgroove arrays might play an important role in enhancing the performance of ultrasonic motors.     

双级高压涡轮气动性能试验状态模化方法

针对双级高压气冷涡轮的低温试验状态模化方法，对以空气为工质、基于不同相似准则数的试验模化状态的流场相似 性进行数值仿真。结果表明：对于有冷气试验模化方法，采用出口马赫数与设计状态一致的模化方法可获得相似性较好的试验状 态流场，此时反力度、载荷系数、马赫数均能保证良好的相似性，主要相似准则数偏差不超过5%；对于无冷气试验模化方法，保持 涡轮几何不变并增大膨胀比使得等熵速比与设计状态的一致，或通过改变叶片数保证各排出口马赫数与设计状态的一致，均能显 著改善无冷气模化状态与设计状态的流场相似性。其中前者反力度相似性接近98%，而后者载荷系数和马赫数的相似性达到了 同样水平，但破坏了模型的几何相似。     

改进的小波均匀化方法求解小周期系数抛物型方程

对传统的小波数值均匀化方法通过加入逐层修正的步骤进行了改进,并将改进后的方法用于求解具有小周期系数的抛物型方程。数值算例结果表明：在保持较高计算效率的同时,改进后的方法比改进前方法在精度方面有明显的提高。因此,改进后方法是小周期系数抛物型方程的一种高效率、高精度的数值求解方法。     

Anomalous Cosmic Rays and Solar Modulation

We review aspects of anomalous cosmic rays (ACRs) that bear on the solar modulation of energetic particles in the heliosphere. We show that the latitudinal and radial gradients of these particles exhibit a 22-year periodicity in concert with the reversal of the Sun's magnetic field. The power-law index of the low energy portion of the energy spectrum of ACRs at the shock in 1996 appears to be -1.3, suggesting that the strength of the solar wind termination shock at the helioequatorial plane is relatively weak, with s 2.8. The rigidity dependence of the perpendicular interplanetary mean free path in the outer heliosphere for particles with rigidities between 0.2 and 0.7 GV varies approximately as R2, where R is particle rigidity. There is evidence that ACR oxygen is primarily multiply charged above 20 MeV/nuc and primarily singly-charged below 16 MeV/nuc. The location of the termination shock was at 65 AU in 1987 and 85 AU in 1994.     

螺纹的综合测量和单项测量

简要介绍了螺纹测量的现状和目前存在的问题,讨论了螺纹测量需要研究的几个问题,分析了螺纹单项参数测量和综合测量的关系以及螺纹量值传递技术.具体介绍了实现内螺纹中径参数测量的测量原理、测量方法和测量中的问题.     

航空反潜作战效果综合评估

将模糊评判理论应用于航空反潜作战效果评估,通过给定的反潜作战剖面以及军事分析目标树,建立模糊综合评判模型,分析目标树各层因素之间的权重关系,运用模型进行计算,最终得到评估结果,为作战效果量化分析作一些基础研究。     

基于遗传算法的一种高分辨率雷达目标识别方法

目标识别是防空信息处理中的一个重要环节,而对空中目标类型的识别还没有成熟的理论。通过对高分辨雷达回波信号的分析,在遗传算法的基础上,提出了一种高分辨雷达目标识别方法,由此进行目标识别。仿真实验结果表明,该方法具有高的识别率和强的抗干扰能力。     

气膜冷却孔几何结构对流量系数的影响

为了研究火焰筒壁面气膜冷却孔几何结构对流量系数的影响规律，设计了几种具有不同几何尺寸和排列结陶的气膜冷却孔实验件。对气膜冷却孔的流量系数进行了实验研究。实验结果表明．在吹风比较小时．随吹风比的增加流量系数大幅度增加．当吹风比较大时，随吹风比的增加流量系数增幅减小。同时．在气膜孔厚径比大于1时，气膜孔的排列形式对流量系数的影响不大，当厚径比小于1时．叉排气膜孔的流量系数要高于顺排气膜孔的流量系数。     

SAR扫描区域目标模型分析

根据雷达目标测绘区域的特点，结合地面目标的特性系统，给出了合成孔径雷达的目标测绘区域目标的模拟目标模型。根据该区域目标模型可以计算出测绘区域的目标回波信号，经处理后得到测绘区域图像。实验结果表明该区域目标模型可满足对目标回波的处理要求。     

塞式喷管主喷管角度特性

首先建立了塞式喷管角度特性的研究模型，并运用简化的塞锥设计方法设计塞锥型面，在此基础上，通过连续改变主喷管倾角来研究主喷管倾角对塞式喷管的推力性能的影响，并确定在给定设计条件下的主喷管最佳倾角，还分析研究了底部高度，内膨胀比，总膨胀比，总压和飞行高度与主喷管最佳倾角的关系以及变化规律，针对特定的塞式喷管实验发动机，进行了初步的变角度实验，并与计算结果进行比较和分析。