一种具备星间链路的中轨对地观测星座设计

采用轨道高度为2165.6 km、回归周期为1天的太阳同步回归轨道建立了一个包含6颗卫星、具备星间链路的中轨对地观测星座。通过卫星自身的侧摆姿态机动功能,可以实现对同一目标1天之内的多次观测,以完成区域性准实时成像、灾害灾情监测等任务,极大地提高了观测的时间分辨率。在星座内部,相邻两颗卫星之间建立了5000 bit/s码速率测控和250 Mbit/s码速率数传的星间链路,能够充分利用单颗卫星在境内的可视弧段,通过地面与单颗卫星建立星地链路就可以同时完成与所有卫星的星地通信。     

In-situ observation and finite element analysis of fretting fatigue crack propagation behavior in 1045 steel

In this paper fretting fatigue crack behavior in 1045 steel is studied by in-situ observation and finite element analysis. in-situ fretting fatigue experiments are conducted to capture real-time fretting fatigue crack formation and propagation process. The fretting fatigue tests under different load conditions are carried out, then the lifetime and fracture surface are obtained. The crack propagation rates under different loading conditions are measured by in-situ observations. With in-situ observation, crack initiation location and direction are analyzed. Finite element model is used to calculate J-integral which then is applied to fitting with experimental crack growth rate, and establishing crack growth rate model. From fitted S-N curve, it turns out that smaller load ratio leads to higher lifetime. Crack initiates slightly below the point equivalent to line contact of the contact surface in different test conditions, and crack direction shows no obvious relationship with load parameters. The established crack growth rate model well agrees with the test results.     

Mission analysis and systems design of a near-term and far-term pole-sitter mission

This paper provides a detailed mission analysis and systems design of a near-term and far-term pole-sitter mission. The pole-sitter concept was previously introduced as a solution to the poor temporal resolution of polar observations from highly inclined, low Earth orbits and the poor high-latitude coverage from geostationary orbit. It considers a spacecraft that is continuously above either the north or south pole and, as such, can provide real-time, continuous and hemispherical coverage of the polar regions. Being on a non-Keplerian orbit, a continuous thrust is required to maintain the pole-sitter position. For this, two different propulsion strategies are proposed, which result in a near-term pole-sitter mission using solar electric propulsion (SEP) and a far-term pole-sitter mission where the SEP thruster is hybridized with a solar sail. For both propulsion strategies, minimum propellant pole-sitter orbits are designed. In order to maximize the spacecraft mass at the start of the operations phase of the mission, the transfer from Earth to the pole-sitter orbit is designed and optimized assuming either a Soyuz or an Ariane 5 launch. The maximized mass upon injection into the pole-sitter orbit is subsequently used in a detailed mass budget analysis that will allow for a trade-off between mission lifetime and payload mass capacity. Also, candidate payloads for a range of applications are investigated. Finally, transfers between north and south pole-sitter orbits are considered to overcome the limitations in observations due to the tilt of the Earth's rotational axis that causes the poles to be alternately situated in darkness. It will be shown that in some cases these transfers allow for propellant savings, enabling a further extension of the pole-sitter mission.     

一种空间视觉测量子系统用半导体 激光器驱动电路设计

针对面阵静态红外地球敏感器的现场标定,提出基于规则小孔平面靶标的现场标定方法.将小孔平面靶标固定放置于面源黑体前方,在光学视场测量空间内,多次调整红外地球敏感器的摆放位置,以采集多幅不同位置、不同角度的红外靶标光点图像.使用等高层最小二乘椭圆拟合方法精确提取靶标红外光点的中心坐标,获得特征点信息.利用红外靶标图像和图像特征点计算面阵静态红外地球敏感器光学系统的焦距和主点坐标.试验结果表明,该标定方法简单灵活有效,便于调试现场操作.目前,该方法已在面阵静态红外地球敏感器研究中得到应用.     

恒定应力无失效加速寿命试验可靠性分析方法

针对工程中缺少有效方法处理加速寿命试验中出现的无失效数据的情况,提出一种恒定应力水平下的无失效加速寿命试验可靠性分析方法.该方法首先将各个加速应力水平下的无失效寿命试验数据转换到正常应力水平,然后通过对正常应力水平下的无失效寿命数据进行分析,实现产品的可靠性评估与寿命预测.利用该方法对某型号卫星地球敏感器扰性枢轴的无失效加速寿命试验数据进行分析处理,结果表明该方法切实可行,能够充分利用各个加速应力水平下产品的无失效试验数据,较好地解决了产品进行无失效加速寿命试验的可靠性评估和寿命预测问题.      

基于单频星载GPS数据的低轨卫星精密定轨

为满足搭载单频GPS接收机低轨卫星的精密定轨需求以及深化单频定轨研究,文中解决了单频星载GPS数据的周跳探测问题,并利用“海洋二号”（HY-2A）卫星及“资源三号”（ZY-3）卫星的单频星载GPS实测数据采用两种方法确定了二者的简化动力学轨道,并通过观测值残差分析、与双频精密轨道比较、激光测卫数据检核等方法对所得轨道精度进行评定。结果表明,在不考虑电离层延迟影响的情况下,HY-2A卫星定轨精度为2~3dm,ZY-3卫星为1m左右;而采用半和改正组合消除电离层延迟一阶项影响后,二者定轨精度均显著提高,HY-2A卫星三维精度提高至1dm左右,ZY-3卫星提高至1~2dm。文章的研究成果表明,搭载单频GPS接收机的低轨卫星也可获得厘米级的定轨精度。     

航天器太阳翼在轨光照角度建模及仿真分析

航天器太阳翼的输出功率受到光照条件的影响,与太阳光入射角θ（指太阳光与太阳翼法线的夹角,以下简称θ）密切相关（θ角取值0°～60°范围之间,输出功率与θ的余弦成正比）。为此建立了高精度的轨道数值计算模型、太阳位置计算模型、光照地影模型和不同姿态模式（航天器的飞行模式和太阳翼定向模式的多种组合模式）下的太阳光入射角计算模型。根据轨道和姿态条件,推算航天器在轨运行过程中太阳翼的太阳光入射角,分析太阳光入射角随时间的变化。仿真结果可用于计算太阳翼的发电功率,并为航天器和太阳翼的姿态控制提供参考。     

在轨航天器地气光环境分析

为得出定量化的遥感观测地气光环境数据,建立了简化的航天器地气光分布计算模型,首先将航天器及其各类运行轨道归纳到统一的照明模式中,地气光的分布主要考察航天器轨道面与地球晨昏面的夹角,然后考察航天器在每轨中的具体相位,以建立照度的几何传递关系;随后考察太阳辐照经地表后,最终到达航天器遥感观测载荷的光照度.计算结果能反映地气光在载荷观测方向2π半球视场内的分布情况,根据分布随空间变化的具体量级,对不同的离轴角进行照度积分,可转化为对观测仪器的地气光抑制能力要求.      

资源卫星数据地面存储管理系统的设计与实现

MVC(Model-View-Controller)软件设计模式是目前广泛流行的软件设计模式之一。它将数据表示、流程控制和数据处理进行分离。通过采用MVC模式,可以简化软件开发,提高软件的伸缩性、扩展性和可维护性,达到提高软件质量的目的。结合面向对象的MVC软件设计模式和资源卫星数据的特点,文章提出并阐述了一种基于MVC模式的资源卫星产品数据地面存储管理系统的设计方法。该设计方法已应用于资源卫星地面系统的工程建设中。目前该业务系统运行稳定,证明了基于MVC模式的资源卫星数据地面存储管理系统设计合理、可行。     

一种快速检测GPS卫星完好性风险的方法

提出了一种观测量组合算法对完好性风险进行了监测;并针对多接收机单统计量的线性组合进行了讨论;最后利用实际数据对该统计方法进行验证。研究结果表明:在发生失效的情况下,观测量组合算法能够更快地监测故障的发生,提高了对故障的检测速度,同时可检测出小偏差故障,降低系统的漏检率。