涡轴发动机燃气涡轮叶片动应力测试技术研究及验证

针对涡轴发动机高转速燃气涡轮叶片动应力测试中出现的应变计短路、高温导线断裂和线芯窜动问题,开展了动应力测试技术研究。提出了加宽基底喷涂固定应变计、优化高温导线布线、改进高温导线等工艺方法,并进行了试验验证。试验结果表明,共振转速试验测试值与计算值基本一致,共振转速测试结果准确有效。通过研究,获得了具有实际应用价值的涡轴发动机燃气涡轮叶片动应力测试技术,可为同类测量提供参考。     

基于单应性矩阵的模型迎角单目视频测量方法

风洞试验中模型迎角的精准测量是降低阻力系数误差的重要途径之一,为此,提出了基于单应性矩阵的模型迎角单目视频测量方法。该方法通过两个单应性矩阵,获取试验过程中相机实时位姿和标记点物方空间位置坐标,应用坐标旋转关系,完成试验模型的迎角测量。数值仿真试验结果表明：迎角测量误差与待测标记点到风洞壁板间的距离偏差近似为线性关系,因此,当标记点不满足共面条件时,可根据该特点进行测量误差修正。静态标定和风洞迎角测量试验结果表明：修正系统误差后,迎角实测数据的测量准度在0.01°以内,精度不超过0.012°。本文方法易于实施,工程实用价值强。     

尖侧缘机身布局的俯仰力矩特性及扰流板控制

针对尖侧缘机身布局在大迎角下存在的正俯仰力矩（抬头力矩）问题,通过风洞试验,首先研究了俯仰力矩的迎角分区特性及流动演化规律：线性增长区（迎角为0°~15°）,俯仰力矩线性增加,全机从附着流到形成进气道前缘涡和机翼涡;非线性增长区（迎角为17.5°~32.5°）,俯仰力矩非线性增加,机头涡出现,机头涡和进气道前缘涡逐渐增强,机翼涡增强后破裂;衰减区（迎角为35°~65°）,俯仰力矩逐渐减小,机头涡增强后破裂,进气道前缘涡破裂发展,机翼涡完全破裂。其次,发现了机身前体是产生正俯仰力矩的主要来源,机头涡是导致大迎角下正俯仰力矩的主控流动。当迎角为40°时,前体各截面正俯仰力矩在进气道前缘处达到最大,主要是由于该处机头涡诱导产生了较强的法向力。最后,提出了大迎角机身扰流板控制技术,产生了较好的控制效果。当迎角为40°时,扰流板可使正俯仰力矩减少62%,其原因是扰流板降低了机头涡涡量及其诱导产生的法向力,减少了机身前体对正俯仰力矩的贡献。该控制技术的缺点是扰流板会带来一些升力损失和附加阻力。基于尖侧缘机身参考宽度的雷诺数为2.59×10⁵。     

对转螺旋桨流场气动干扰数值模拟

基于结构网格动态面搭接技术,通过求解三维非定常雷诺平均纳维-斯托克斯(RANS)方程,对单独螺旋桨(SRP)滑流流场进行了数值模拟,结果与风洞试验数据吻合良好,在此基础上深入研究了对转螺旋桨（CRP）的非定常滑流效应及前后桨之间的气动干扰现象。计算结果表明:所采用的非定常RANS方法能够良好刻画对转螺旋桨滑流流场的发展变化特征,适用于分析前后桨气动干扰特性。前后桨桨尖涡的复杂相互作用是导致对转螺旋桨气动干扰的直接原因,后桨桨尖涡对于前桨桨尖涡具有一定耗散作用。在气动干扰影响下,对转螺旋桨气动力会产生周期性波动,波动周期与螺旋桨桨叶数相关, 6×6对转螺旋桨在1个旋转周期内产生了12次波动。气流穿过对转螺旋桨会发生两次加速,因此在相同工况下,对转螺旋桨的拉力系数和功率系数相比于单独螺旋桨分别增大约1倍,效率提升约1.5%。      

耦合热、动载荷的超超临界汽轮机迷宫密封动力特性

密封汽流激振严重影响超超临界汽轮机的安全运行,采用DEFINE_CG_MOTION和DEFINE_PROFILE控制宏建立转子的涡动方程,通过Workbench流固耦合方法计算热、动载荷下密封齿形变,根据快速傅里叶变化得到机组运行时的密封动力特性,并对转子稳定性进行分析。结果表明:蒸汽可导致密封齿膨胀变形,温度对密封齿长度变化影响可达1%~1.5%,压力和离心作用对其影响较小。热、动载荷使迷宫密封直接刚度减小,直接阻尼先增加后减小,交叉刚度先减小后增加,动力系数的最大变化为原来的2倍。35~55 Hz内转子稳定裕度急剧下降,转子对密封汽流激振更敏感。热、动载荷引起的压力波动集中在低频范围,密封周向压力波动可增高18.5 kPa。密封高压区的压力波幅剧增是汽流激振显著的主要原因。      

POD和DMD方法分析不同间隙压气机旋转不稳定性特性

对一台单级低速轴流压气机旋转不稳定性(RI)进行分析。在前期的旋转不稳定性特性、流场成因和不同间隙影响的研究基础上,进一步基于全通道数值模拟,采用两种流场降阶方法分析不同叶顶间隙条件下旋转不稳定性各阶模态对应的流场成分、模态能量占比和稳定性等特性。计算结果表明,前几阶模态能量占比大,对流场起主要贡献,并且稳定性相对较强。随着间隙的减小,旋转不稳定性的能量占比和稳定性下降,各阶的叶片转动成为流场的主要成分。      

基于二阶滑模算法的永磁电机直接转矩控制

针对传统直接转矩控制(DTC)方法低速控制精度差、转矩脉动大、开关频率不稳定等问题,提出了一种基于二阶滑模控制的永磁电机DTC方法。该控制方法基于二阶滑模控制原理,将传统磁链控制器与转矩控制器以滑模控制器替代,对空间电压进行矢量调制,提高了开关频率的稳定性,获得了良好的动态稳定性,改善了电机输出性能。仿真与试验结果表明,该控制方法能够有效减小电流脉动与转矩脉动,同时提高了控制系统的抗干扰能力,实现了电机的快速动态响应,具有较强的鲁棒性能。     

摆线桨非定常动态失速的三维效应

对摆线桨三维全尺寸模型进行了非定常数值模拟。验证了两种嵌套网格方法的可靠性与适用性,针对二维/三维情况下摆线桨非定常涡流动特性及诱导分离特性开展了数值分析,重点研究了展向气动力随方位角的分布与全局流场的诱导速度分布,并分析了尾迹捕捉精度与涡量耗散特征。结果表明:受摆线桨切向速度、展向诱导速度等三维效应影响,两种计算结果的瞬态气动力极值差值达到44%。三维动态失速涡的产生、脱落与再附明显弱于二维翼型情况,这对于摆线桨非定常气动特性有较大影响。      

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.