Predictive Modeling and Parameter Optimization of Cutting Forces During Orbital Drilling

To optimize cutting control parameters and provide scientific evidence for controlling cutting forces,cutting force modeling and cutting control parameter optimization are researched with one tool adopted to orbital drill holes in aluminum alloy 6061.Firstly,four cutting control parameters(tool rotation speed,tool revolution speed,axial feeding pitch and tool revolution radius)and affecting cutting forces are identified after orbital drilling kinematics analysis.Secondly,hybrid level orthogonal experiment method is utilized in modeling experiment.By nonlinear regression analysis,two quadratic prediction models for axial and radial forces are established,where the above four control parameters are used as input variables.Then,model accuracy and cutting control parameters are analyzed.Upon axial and radial forces models,two optimal combinations of cutting control parameters are obtained for processing a13mm hole,corresponding to the minimum axial force and the radial force respectively.Finally,each optimal combination is applied in verification experiment.The verification experiment results of cutting force are in good agreement with prediction model,which confirms accracy of the research method in practical production.     

基于激光旋切法的陶瓷材料盲孔加工方法研究

介绍了激光打孔的基本原理,对激光能量、离焦量、轨迹在激光旋切法加工盲孔过程中对孔形和表面质量的影响进行了分析和试验验证,并给出了一般规律.依据试验结果确定了合理工艺参数,采用旋切法在碳纤维增强碳化硅陶瓷基复合材料（Cf/SiC）上打出了孔径为1 mm,孔深为1.1 mm,锥度小于15°的盲孔.     

声发射监测钻头折断的实验研究

 金属切削过程中会发出声讯号。用声发射技术监测刀具破损是一个很有潜力的新方法。本文研究了声发射技术在钻头折断在线监测中的应用。实验结果表明,所设计的实验监测系统能可靠地监测钻头的折断,并可提前预报直径大于1.5mm钻头的折断。     

镍基单晶高温合金DD6气膜孔热机械疲劳试验

涡轮冷却叶片气膜孔边存在大应力梯度,且服役时承受交变的机械载荷和热载荷,热机械疲劳（TMF）是其主要失效模式。通过开展带气膜孔和不带气膜孔的薄壁圆管试件TMF试验研究了气膜孔对镍基单晶高温合金TMF寿命的影响。结果表明最大循环应力在300~500 MPa应力范围内,循环应力幅值与镍基单晶高温合金TMF寿命呈现良好的对数线性关系,且气膜孔导致镍基单晶高温合金TMF寿命下降可达82.5%。继而完成了横向取向分别为〈010〉、〈110〉方向的气膜孔模拟件试验,结果表明气膜孔取向为〈110〉时寿命最短,仅为〈010〉取向的40.0%。最后开展了不同制孔工艺下的气膜孔模拟件试验,结果表明激光制孔气膜孔模拟试件寿命仅为电液束制孔气膜孔模拟试件的54.0%。气膜孔模拟件断口分析表明:TMF裂纹均萌生于气膜孔边,源区氧化严重;裂纹沿着大致与气膜孔边垂直的方向扩展。      

基于多传感融合的自动钻铆孔位在线测量方法

为了获得飞机壁板自动钻铆中孔位的实际位置和法向信息,提出了一种基于视觉和激光测距多传感器融合的孔位在线测量方法,该方法可以实时获得钻铆任务的孔位偏差修正量,从而保证壁板钻铆质量。首先,通过建立视觉和激光测距传感器与钻铆机参考坐标系间的映射关系,获得了钻铆孔位在线测量的多传感器融合模型,给出了孔位位置和法向的在线测量原理。然后,为了简化标定过程和提高标定精度,设计了一种同时适用于视觉和激光测传感器的标定板,给出了位置和法向测量的标定方法。最后,测量试验表明,多传感融合的在线测量方法孔位测量位置误差≤0.2 mm,法向误差≤0.3°,能够满足飞机钻铆孔位测量精度要求。     

Influence of longitudinal-torsional ultrasonic-assisted vibration on micro-hole drilling Ti-6Al-4V

As Ti-6Al-4V is a typical hard to machine material, especially in micro drilling aviation parts, chip breaking difficulty is of increasing interest to explore its further development. In this study, Longitudinal-Torsional Ultrasonic Assisted Drilling (LTUAD) was employed to machine Ti-6Al-4V, and its feasibility was evaluated by comparing with Conventional Drilling (CD). By combining periodical characteristics and vibration models (the separated or the unseparated ultrasonic elliptical vibration), the influence of ultrasonic frequency on the intersection characteristics of trajectories were analyzed. And the intersection characteristics were divided into four categories: even periodicity, odd periodicity, non-odd and even periodicity and composite periodicity, indicating different capability for chip breaking. By applying the longitudinal-torsional compound vibration horn, the micro-hole drilling experiment was carried out on machining center. The chip morphology, the thrust force, and the burr height were discussed. Experimental results showed that the morphology of chips presented as smaller and more fragmentary ones in LTUAD compared with continuous helical conical ones and fold-shaped ones in CD. Compared with CD, the average values of the thrust force in LTUAD reduced by 1.98% to 24.9%. According to the burr around the hole exit in both LTUAD and CD, the height of the latter was greatly affected by the drilling parameters. And the burr around the exit of the hole were distributed rather evenly with smaller extension in LTUAD. Consequently, the LTUAD employed in micro-hole drilling was effective.     

高低频复合振动钻削CFRP/钛合金叠层结构试验

针对碳纤维增强复合材料（CFRP）和钛合金叠层结构在传统钻削过程中切削温度高、加工质量差等问题,基于低频振动钻削和高频（超声）振动钻削的优势,提出了高低频复合振动钻削的加工方法。采用自主研制的高低频复合振动钻削装置,对CFRP/钛合金叠层结构进行了制孔试验,对比研究了普通钻削、超声钻削、低频振动钻削和高低频复合振动钻削4种方式下的切削力、钛合金切屑形貌、切削温度和CFRP孔加工质量。结果表明：4种加工方式中,高低频复合振动钻削的轴向力波动相对较大,切削温度显著降低,产生的钛合金切屑呈不连续扇形且整体尺寸最小,CFRP孔出入口及孔壁的损伤程度最低,显著提高了加工质量,为复合材料叠层结构一体化制孔加工提供了指导意义。     

碳/环氧复合材料钻削力影响因素的研究

针对碳/环氧复合材料进行了钻孔技术、尤其是高速钻孔技术的研究，紧密结合工程应用的现状，对钻削力及其影响因素进行了较为全面和系统的研究。结果表明：进给量是影响钻削力的主导因素，进给量越大，钻削力越大；进给量越小，钻削力越小。转速、钻尖直径及材料厚度对钻削力也有一定影响，但控制进给量是控制钻削力的最有效措施。     

小孔钻削加工自适应控制

应用装在钻床夹具与工作台之间的测扭、测力压电晶体传感器,同时测量轴向力与扭矩的变化值, 根据所测扭矩、轴向力大小调整钻削进给量,控制钻头轴向进退及排屑,从而保证小孔、深孔的加工效率与可靠性。     

一种新的含转角自由度的四节点杂交元

基于组合杂交变分原理,使用含转角自由度的位移插值和CH(0-1)元应力模式,得到CHD(0-1)单元.它既满足杂交方法所要求的inf-sup条件,又有较高的位移、应力精度;和普通的八节点二次单元相比计算花费少;对单元几何形状不敏感;能很好地模拟弯曲变形.数值试验结果支持了本文结论.