Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

带非线性支撑的转子有限元模型求解方法

用数值方法研究了非线性支撑的柔性转子系统的动学行为,提出了一种将有限元与非线性支撑结合的模型和求解方法。利用有限元法(FEM)构建转轴和转盘部分的模型,通过矩阵进行组合;利用离散元方法对包含滚动轴承和挤压油膜阻尼器(SFD)的支撑部分进行建模,此部分包含4个单元,分别为轴承内圈、外圈、SFD内圈和支撑鼠笼。有限元部分和离散元部分通过轴端节点相连,仿真过程中轴端位移传递给非线性支撑部分,支撑部分通过位移计算得到的非线性力反过来作用于有限元转子轴端部分。为了耦合求解有限元转子和非线性支撑组成的数学模型,提出了一种综合的迭代求解方法,克服传统的有限元求解方法对轴端隐性非线性支撑的求解局限性。由于转轴部分采用了Timoshenko梁单元建模,对比与简单转子模型,可以考虑陀螺力矩和轴的柔性特征,更能体现非线性支撑对振动真实影响。在建立的20个轴单元的有限元转子模型中,非线性响应更多体现在靠近非线性支撑的节点1和节点21处,响应频谱中靠近轴端的节点能体现出滚动轴承的2倍和3倍变柔振动频率。     

转子系统挤压油膜阻尼器设计与动力特性

鉴于挤压油膜阻尼器(SFD)设计必须要同时考虑转子系统的动力学特性,提出了一种转子系统与挤压油膜阻尼器耦合设计方法,给出了详细的设计流程。对所设计的阻尼器进行了CFD数值模拟、油膜压力测量以及减振效果实验,结果证明所提出的设计方法是有效的。相比未采用阻尼器,采用阻尼器后转子系统两个转盘的振幅分别下降了46%和39%。通过实验还研究了不平衡量、支承刚度、供油压力和滑油温度对挤压油膜阻尼器减振效果的影响。结果表明,相比于不平衡量和支承刚度对减振效果的影响,供油压力和滑油温度的影响并不显著。进行挤压油膜阻尼器设计时,重点应该关注转子上的不平衡量大小和支承刚度。     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

相变光盘多层膜系结构的最佳光匹配研究

论述了相变光盘最佳膜系结构的设计。采用导纳矩阵法计算膜系的能量反射率，用量优化计算方法编程计算，提出了第二大极值解作为在工艺上可行的实用光盘的膜系结构，并按这种膜系结构制作样品，其擦写循环数达１００万次上。     

虑及多转速的核心机转子高速动平衡试验

为满足航空发动机整机动平衡对转子不平衡振动精稳抑制的需求，采用虑及多转速状态的转子高速动平衡优化配平方 法，开展了核心机转子动平衡试验。以核心机转子系统为对象，研究在高压压气机转子第4、9级盘上配重抑制高压涡轮振动的可 行性。综合考虑核心机转子在多转速下的振动状态，以残余振动平方和及残余振动最大值为目标函数，采用优化算法对配平方案 进行优化，制定了核心机转子高速动平衡方案。在核心机转子系统试验台上分别进行了单平面-单转速、单平面-多转速、双平面- 单转速以及双平面-多转速动平衡的试验。结果表明：采用虑及多转速状态的转子高速动平衡优化配平方法能使因不平衡引起的 核心机转子振动在工作转速区间内均有所减小。     

旋翼桨叶动力学设计技术

桨叶动力学设计,其实质是求解非线性高维动力学逆问题的具体实施。本文较全面地阐述了这方面的进展情况,提出了切实可行、有效实用的数值方法。     

M数缩尺法旋翼颤振动力相似模型设计

本文以延-2复合材料桨叶旋翼为例,用M数缩尺法尝试设计了缩尺比为1/5的颤振相似模型。设计从旋翼颤振微分方程开始,应用π定理得出10个独立相似准则数,列出各有关物理量缩尺因子后进行模型结构设计,从而得出了若干有益的结论。     

Lift coefficient prediction at high angle of attack using recurrent neural network

In this paper, identification of dynamic stall effect of rotor blade is considered. Recurrent Neural Networks have the ability to identify the nonlinear dynamical systems from training data. This paper describes the use of recurrent neural networks for predicting the coefficient of lift (C_Z) at high angle of attack. In our approach, the coefficient of lift (C_Z) obtained from the experimental results (wind tunnel data) at different mean angle of attack θ_mean is used to train the recurrent neural network. Then the recurrent neural network prediction is compared with experimental ONERA OA212 airfoil data. The time and space complexity required to predict C_Z in the proposed method is less and it is easy to incorporate in any commercially available rotor code.     

Numerical study on flow fields and aerodynamics of tilt rotor aircraft in conversion mode based on embedded grid and actuator model

A method combining rotor actuator disk model and embedded grid technique is presented in this paper, aimed at predicting the flow fields and aerodynamic characteristics of tilt rotor aircraft in conversion mode more efficiently and effectively. In this method, rotor's influence is considered in terms of the momentum it impacts to the fluid around it; transformation matrixes among different coordinate systems are deduced to extend actuator method's utility to conversion mode flow fields' calculation. Meanwhile, an embedded grid system is designed, in which grids generated around fuselage and actuator disk are regarded as background grid and minor grid respectively, and a new method is presented for ‘donor searching' and ‘hole cutting' during grid assembling. Based on the above methods, flow fields of tilt rotor aircraft in conversion mode are simulated, with threedimensional Navier–Stokes equations discretized by a second-order upwind finite-volume scheme and an implicit lower–upper symmetric Gauss–Seidel(LU-SGS) time-stepping scheme. Numerical results demonstrate that the proposed CFD method is very effective in simulating the conversion mode flow fields of tilt rotor aircraft.