Validation of non-linear split window algorithm for land surface temperature estimation using Sentinel-3 satellite imagery: Case study; Tehran Province,Iran

In recent years, land surface temperature (LST) has become critical in environmental studies and earth science. Remote sensing technology enables spatiotemporal monitoring of this parameter on large scales. This parameter can be estimated by satellite images with at least one thermal band. Sentinel-3 SLSTR data provide LST products with a spatial resolution of 1 km. In this research, direct and indirect validation procedures were employed to evaluate the Sentinel-3 SLSTR LST products over the study area in different seasons from 2018 to 2019. The validation method was based on the absolute (direct) evaluation of this product with field data and comparison (indirect) evaluation with the MODIS LST product and the estimated LST using the non-linear split-window (NSW) algorithm. Also, two emissivity estimation methods, (1) NDVI thresholding method (NDVI-THM) and (2) classification-based emissivity method (CBEM), were used to estimate the LST using the NSW method according to the two thermal bands of Sentinel-3 images. Then, the accuracy of these methods in estimating LST was evaluated using field data and temporal changes of vegetation, which the NDVI-THM method generated better results. For indirect evaluation between the Sentinel-3 LST product, MODIS LST product, and LST estimated using NSW, four filters based on spatial and temporal separates between pairs of pixels and pixel quality were used to ensure the accuracy and consistency of the compared pairs of a pixel. In general, the accuracy results of the LST products of MODIS and Sentinel-3, and LST estimated using NSW showed a similar trend for LST changes during the seasons. With respect to the two absolute and comparative validations for the Sentinel-3 LST products, summer with the highest values of bias (?1.24 K), standard deviation (StDv = 2.66 K), and RMSE (2.43 K), and winter with the lowest ones (bias of 0.14 K, StDv of 1.13 K, and RMSE of 1.12 K) provided the worst and best results for the seasons in the period of 2018–2019, respectively. According to both absolute and comparative evaluation results, the Sentinel-3 SLSTR LST products provided reliable results for all seasons on a large temporal and spatial scale over our studied area.     

Establishment of atmospheric weighted mean temperature model in the polar regions

Due to the special geographical location and extreme climate environment, the polar regions (Antarctic and Arctic) have an important impact on global climate change. Atmospheric weighted mean temperature (Tm) is a crucial parameter in the retrieval of precipitable water vapor (PWV) from the zenith wet delay (ZWD) of ground-based Global Navigation Satellite System (GNSS) signal propagation. In this paper, the correlation between weighted mean temperature and surface temperature (Ts) is studied firstly. It is shown that the correlation coefficients between Tm and Ts are 0.93 in the Antarctic and 0.94 in the Arctic. The linear regression Tm model and quadratic function Tm model of the Antarctic and the Arctic are established respectively using the radiosonde profiles of 12 stations in the Antarctic and 58 stations in the Arctic from 2008 to 2015. The accuracies of the linear regression Tm model, the quadratic function Tm model and GPT2w Tm model which is a state-of-the-art global Tm model are verified using the radiosonde profiles from 2016 to 2018 in the Antarctic and Arctic. Root Mean Square (RMS) errors of the linear regression Tm model, the quadratic function Tm model and GPT2w Tm model in the Antarctic are 3.07 K, 2.87 K and 4.32 K respectively, and those in the Arctic are 3.53 K, 3.38 K and 4.82 K, which indicates that the quadratic function Tm model has a higher accuracy compared to linear regression Tm model, and the accuracies of the two regional Tm models are better than that of GPT2w Tm model in the polar regions. In order to better evaluate the accuracy of Tm in the PWV retrieval, the PWV values of radiosondes are used for comparisons as the reference value. The RMS errors of PWV derived from the two Tm models are similar for 1.28 mm in the Antarctic and 1 mm in the Arctic respectively. In addition, the spatial and temporal variation characteristics of Tm are analyzed in the polar regions by spectral analysis of Tm data using fast Fourier transform. The results show that the Tm has obvious seasonality and annual periodicity in the polar regions, and the maximum difference between warm season and cold season is about 63 K. After comparing and analyzing the influences of latitude, longitude and elevation on the Tm in the polar regions, it is found that latitude and elevation have a greater influence on the Tm than the longitude. As the latitude and elevation increase, the Tm decreases, and vice versa in the polar regions.     

A new modeling scheme for powered parafoil unmanned aerial vehicle platforms: Theory and experiments

A novel framework is established for accurate modeling of Powered Parafoil Unmanned Aerial Vehicle (PPUAV). The model is developed in the following three steps: obtaining a linear dynamic model, simplifying the model structure, and estimating the model mismatch due to model variance and external disturbance factors. First, a six degree-of-freedom linear model, or the structured model, is obtained through dynamic establishment and linearization. Second, the data correlation analysis is adopted to determine the criterion for proper model complexity and to simplify the structured model. Next, an active model is established, combining the simplified model with the model mismatch estimator. An adapted Kalman filter is utilized for the real-time estimation of states and model mismatch. We finally derive a linear system model while taking into account of model variance and external disturbance. Actual flight tests verify the effectiveness of our active model in different flight scenarios.     

Near-wall topological patterns and flow structures over a simplified Danaus plexippus model

Studies on the high-lift mechanisms of butterfly gliding flights shed light on the design of the micro air vehicles. The flow field around a simplified Danaus plexippus model is investigated using the hydrogen bubble visualization and the Particle Image Velocimetry (PIV) techniques. There are three near-wall topological patterns with different Angles of Attack (AoAs): the separation bubble, the Leading-Edge Vortex (LEV) and the high AoAs flow. For the separation bubble pattern, two saddles and two foci form in the middle of the model. The features of the LEV pattern are the leading-edge separation lines. The topological characteristics of the separation lines are changed by the interaction between the LEV and the Wing-Tip Vortex (WTV). For the high AoAs flow pattern, four unstable foci are found at the forewing and the hindwing respectively. The angle between the trajectory of the WTV and the model increases with increasing AoA even though the slope of the WTV angle versus AoA curve declines at the moderate AoAs.     

基于有限Fourier级数的航天器转移轨迹设计

针对航天器小推力转移轨迹的初始设计问题，利用基于三阶Fourier级数的设计方法实现了航天器小推力的多圈转移。同时，基于有限Fourier级数的形状法，对具有多个约束条件的小推力多圈转移轨迹进行了优化设计。选取了共面同轴同偏心率的初始和末端轨道位置，对所提出的方法进行了仿真验证。结果表明：与改进逆五阶多项式形状法相比，所提出的方法虽然增加了转移时间，但当转移圈数为5圈、有限Fourier级数的项数为10时，可减少将近75%的转移速度增量，同时大大减小了所需的最大推力加速度的值。     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

Study of the rheological properties of water and Martian soil simulant mixtures for engineering applications on the red planet

The rheological properties of mixtures of water and the Martian soil simulant JSC-Mars-1A are investigated by preparing and testing samples at various solids concentrations. The results indicate that the dispersion is viscoelastic and, at small timescales (～0.1?s), reacts to sudden strain as an elastic solid. At longer timescales the dispersion behaves like a Bingham fluid and exhibits a yield stress. Hysteresis loops show that rapid step-changes (2?s duration) of shear-rate result in thixotropic behaviour, but slower changes (>10?s duration) can result in rheopexy. These observations are explained with the breakdown and recovery of the packing structure under stress. The rheological information is used to generate practical tools, such as the system curve and the Moody chart that can be used for designing piping systems, and calculating pump sizes and pressure requirements.     

Real-time clock comparison and monitoring with multi-GNSS precise point positioning: GPS,GLONASS and Galileo

The precise point positioning (PPP) technique is widely used in time and frequency applications. Because of the real-time service (RTS) project of the International GNSS Service, we can use the PPP technique for real-time clock comparison and monitoring. As a participant in the RTS, the Centre National d’Etudes Spatiales (CNES) implements the PPPWIZARD (Precise Point Positioning with Integer and Zero-difference Ambiguity Resolution Demonstrator) project to validate carrier phase ambiguity resolution. Unlike the Integer-PPP (IPPP) of the CNES, fixing ambiguities in the post-processing mode, the PPPWIZARD operates in the real-time mode, which is also called real-time IPPP (RT-IPPP). This paper focuses on applying the RT-IPPP for real-time clock comparison and monitoring. We review the principle of real-time clock comparison and monitoring, and introduce the methodology of the RT-IPPP technique. The observations of GPS, GLONASS and Galileo were processed for the experiments. Five processing modes were provided in the experiment to analyze the benefits of ambiguity resolution and multi-GNSS. In the clock comparison experiment, the average reduction ratios of standard deviations with respect to the G PPP mode range from 9.7% to 35.0%. In the clock monitoring experiment, G PPP mode can detect clock jumps whose magnitudes are larger than 0.9 ns. The RT-IPPP technique with GRE PPP AR (G) mode allows for the detection of any clock jumps larger than 0.6 ns. For frequency monitoring, G PPP mode allows detection of frequency changes larger than 1.1 × 10⁻¹⁴. When the RT-IPPP technique is applied, monitoring with GRE PPP AR (G) mode can detect frequency changes larger than 6.1 × 10⁻¹⁵.     

DME询问信号捕获的设计与实现

捕获询问信号是DME地面设备的一个重要功能组成部分。现役的地面设备中大多使用的捕获单元为分离器件电路设计，其电路复杂，控制难度大，改进与维护成本高。针对这些问题，本文设计采用ADC结合FPGA作为主要功能器件，并通过软件算法完成数字滤波、脉冲峰值提取和半幅点计算，实现询问信号的识别与捕获。不仅大幅减少元器件的使用，缩小设备体积，还可提高扩展性与可靠性。结合机柜验证测试，结果符合设计要求。     

A novel framework for liquid propellant engine’s cooling system design by sensitivity analysis based on RSM and multi-objective optimization using PSO

One of the challenges of combustion chamber and nozzle design in a Liquid Propellant Engine (LPE) is to predict the behavior and performance of the cooling system. Therefore, while designing, the optimization of the cooling system is always of great importance. This paper presents the multi-objective optimization of the LPE’s cooling system. To this end, a novel framework has been developed, resulting from the application of the Response Surface Method (RSM) and the correlation coefficients matrix, sensitivity analysis and the The Particle Swarm Optimization (PSO). based on this method, the input variables, constraints, objective functions, and their surfaces were identified. In terms of multi-optimization algorithms, RSM and PSO are utilized to get global optimum. In conclusion, the methodology capability is to optimize the LPE’s cooling system, 6 percentage increase in total heat transfer and 7 bar decrease cooling system pressure loss, which resulted in a 1.2-seconds increase in the specific impulse of the engine.