高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

Corrosion mechanism investigation of TiN/Ti coating and TC4 alloy for aircraft compressor application

It is imperative to develop multifunctional erosion and corrosion resistant coatings for compressor blades of aircraft engines in harsh environment. PVD (Physical Vapor Deposition) technology has the advances in processing erosion-resistant coatings; however, the performance of PVD coatings to combat corrosion depends on various coating defects. Determining and comparing the corrosion performances of PVD TiN/Ti coating and uncoated TC4 alloy was the main objective of present work. The 960 h salt spray corrosion and 116 h hot corrosion tests were conducted to simulate the grounding and working environments of the aircraft compressors. The corrosion mechanisms due to the coating defects such as pinhole, columnar boundary and large grain were analyzed based on the OM, Confocal microscope, electrochemical measurements, SEM, XRD and EDS results. Owing to the disordered state associated with the columnar boundary and the coating defect, nitrogen could be easily replaced by oxygen in the hot corrosion process, these structures were channels for fast diffusion of oxygen. Moreover, the Gibbs energy changes of Ti oxidation and TiN oxidation were thermodynamically calculated according to the working condition of aircraft compressors, and considerable research effort was focused on mapping out the phase diagram of Ti, TiN and high pressure gases. The findings of this research can provide insights into developing multifunctional coatings for future aircraft engines.     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

用于光波纳米推力器的颗粒供应技术和光聚积技术研究

为提高光波纳米推力器在轨应用的可行性,针对与其匹配的颗粒供应技术和光聚积技术进行研究。提出整个推进系统的设计思路,通过建立理论计算和数值计算模型,分析颗粒供应技术和光聚积技术的各项核心结构参数的设计方法。计算结果表明:颗粒供应装置的正负电极内径之比(W/D)会影响正负电荷产生的总量之比,在W/D=300/322附近时,正负电荷比例接近1:1。静电诱导电压为9 V,当中和通道长度大于37.5mm时,正负颗粒可以视为完全中和。光聚积设计思路可令聚积球对光能的利用率在32.8%左右。两种相关技术的装置与推力器在结构上能够对接、在性能上可以匹配,从理论上表明了两种支撑技术的可行性。     

舰载直升机理论风限图飞行模拟获取方法

获取舰载直升机实用风限图,仅依靠实装飞行试验或建模仿真都是非常困难的。通过起降飞行模拟试验获取理论风限图,结合少量的海上实装飞行验证试验是一种综合较优的方法。起降飞行模拟试验需要真实飞行员和高等级飞行模拟器参与,飞行模拟器中的母舰气流场数据、母舰运动可由建模仿真或试验测试得到,且必须考虑母舰气流场的非定场特性;只有当飞行员视景或视觉反馈受限时(如能见度降低时),飞行模拟器基座的六自由度运动才是必需的;用DIPES或Bedford方法量化飞行员主观操纵负担,结合记录的客观操纵数据,评判起降难度;典型的飞行模拟试验程序包含了不同风况下的进近和甲板着舰,通常每隔15°和5kn一个风况。通过起降飞行模拟试验得到的理论风限图,可以更加有效和安全地指导海上实装飞行验证试验,最终获得实用风限图。     

有、无障碍物爆震管起爆过程的CE/SE模拟

用时空守恒元和解元(CE/SE)法模拟有无障碍物情况下爆震管二维爆震波的形成和传播过程,分析爆震波的不同机理,研究在较低能量下,点火区温度、爆震管管径以及障碍物对爆燃-爆震转捩过程(DDT)的影响.控制方程采取无量纲形式,用拓展的隐式梯形法实现刚性源项积分.研究表明,点火能量与点火压力相关,在较低的点火能量下,可以通过提高点火温度、减小爆震管径及加入障碍物加强爆震过程,减小爆燃-爆震转捩过程DDT时间和距离.为研究爆震波点火和DDT过程提供了理论依据.      

结冰实验段空气-水混合流动过程的数值模拟

针对结冰实验段内低温空气与高温雾化水滴的混合流动过程进行了数值模拟,采用拉格朗日方法建立了空气-游离水滴/冰粒多相混合流动与传热传质的一维分析模型,考虑了水滴粒径分布、相变及空气-水滴/冰粒传热传质等因素,求解了流道内气流温度/湿度/速度,水滴温度/速度/半径等参数沿流动方向的变化,分析了水滴粒径分布、气流温度、液态水含量、相对湿度等参数对流动与传热过程的影响,与已有数据的对比验证了模型及结论的正确性.      

精密跟瞄Hexapod平台研制及其振动控制

为了实现星载光学设备的精密跟瞄,以自行研制的宏/微双重驱动复合作动器为主动元件,设计了合理的平台构型,选择并装配了铰链等关键部件,组装完成了具有振动主动控制和大幅跟瞄能力的Hexapod平台原理样机。利用牛顿-欧拉法建立了Hexapod平台线性动力学模型。采用改进的自适应振动消减器(ADC)方法进行了平台主动隔振的控制仿真与实验研究。由仿真结果可知,当Hexapod平台底部受到方向不同的双频正弦微振动干扰时,控制可以隔离干扰向平台上平面的传播;在实验中,平台上平面处于水平位置及转动一定角度时,底部微扰动引起的各杆振幅均下降了90%左右。结果表明了所研制的Hexapod平台用于主动隔振的可行性、建模的有效性以及改进的ADC方法的合理性。     

考虑外圈局部缺陷的滚动轴承非线性动力特性

 建立了考虑滚动轴承外圈局部缺陷、非线性轴承力和径向游隙等非线性因素的滚动轴承系统动力学微分方程,并用Runge-Kutta-Felhberg算法对其求解。利用分岔图、Poincaré映射图、频谱图以及均方值、峰值因子、峭度等时域参数,分析了滚动轴承的响应、分岔和混沌等非线性动力特性。结果表明：考虑外圈局部缺陷的滚动轴承系统存在多种周期、拟周期和混沌响应;滚动轴承系统进入混沌的主要途径是倍周期分叉;峰值因子比率在中、低速,峭度比率在低速时可以很好地识别外圈局部缺陷。均方值比率除了在与轴承动力特性有关的个别转速外,可以在较大的转速范围识别外圈局部缺陷。     

结构的概率-非概率混合可靠性模型

将影响结构可靠性分析的不确定性因素用概率和非概率两种方式模拟。并基于结构可靠性分析中的概率可靠性模型和非概率集合可靠性模型,提出一种新的结构可靠性分析的概率-非概率混合模型。该模型首先通过将功能函数进行非概率可靠性分析,然后将标准化区间变量空间所有区域的可靠度进行求和计算,从而给出结构的可靠度。并根据相同的不确定信息,由混合可靠性模型与概率可靠性模型得到的结果是相等的,证明了方法的有效性。最后,通过一个典型结构和一个机翼下壁加筋板与传统概率可靠性模型进行比较,表明该混合模型对于结构的分析和设计更为合理,能够更好地保证结构的安全性。