一种基于P2P技术的免疫网络入侵检测模型研究

提出一种基于对等网(P2P)技术的免疫网络入侵检测方法,建构了一个P2P免疫网络,定义自体/非自体,实现了免疫学习、疫苗接种等过程.仿真实验表明,该方法能有效提高免疫学习效率,降低免疫计算的FP.     

高能CO2激光腔镜高反介质薄膜的传输特性

为了获得适用于高能CO2激光器的高抗破坏阈值高反薄膜,以10.6μm高反膜ZnSe/YbF3,PbTe/BaF2膜系为例,数值模拟了激光在高反介质膜中的传输的场特性;给出了激光在多层介质膜中的场强分布、温度场分布及热应力分布。结果表明硅镜基体上的PbTe/BaF2膜系所需膜层厚度小、膜层数少,反射率可高达99.98%。     

金属图象分割的研究

结合金属图象的特点,利用传统阚值分割技术和基于最大熵原则的图象分割技术对金属图象分割进行了分析;并根据金属图象分析要求,提出了先二值化金属图象再进行边缘提取的方法.对比实验结果表明,基于最大熵原则的图象分割技术可以获得较好的分割效果,所提出的方法能够获得连续闭合的晶粒边缘,为下一步的金属图象分析提供了可靠的依据.     

基于联邦滤波器的新型故障检测结构及算法

提出了一种基于联邦卡尔曼滤波器的故障检测结构,该结构利用各局部滤波器和参考滤波器共有状态之间的残差进行故障检测.并提出了2种故障检测算法:χ2检验法和Elman神经网络检验法.以组合导航系统为例进行了仿真研究,和其它算法相比该算法计算简单、可靠,不但可以快速检测出外部传感器及参考系统故障,且具有很好的容错性能,能快速检测出故障并进行隔离,使融合后系统依然保持较高精度.     

大型转动机械碰摩故障分析的声发射检测系统

汽轮发电机、空气压缩机等采用油膜支撑的大型转动机械,由于安装或运行中的原因,在转子旋转过程中,可能和器壁发生轻微的摩擦和碰击,简称碰摩.声发射技术在碰摩发生特别是故障早期诊断上有优越性.本系统的特点是没有沿用传统的计数、幅度、能量和持续时间等声发射特性参数,而是在声发射包络信号的频率分析中进行特征提取.声发射发生的过程分析和现场试验都表明这种方法对碰摩检测很敏感,在碰摩发生的起始阶段,包络谱中与转速同步的周期性分量显著增加.根据这种新的设计思想自行研制了BUAA碰摩声发射检测仪并对此作了介绍.     

应用加权中值滤波法检测薄壁梁式挠性器件下摆量

应用加权中值滤波法对薄壁梁式挠性器件下摆量进行高准确度CCD检测。薄壁梁式挠性器件在测量过程中测量图像存在高频抖动现象,因此测量准确度不高,运用加权中值滤波后使用最小二乘法细分技术,可以在实现提高测量准确度的同时,消除高频抖动带来的误差,从而可以有效提高CCD测量薄壁梁式挠性器件下摆量的准确度。实验表明,该方法比传统测量方法准确度提高20倍以上。     

Hybrid integration method for highly maneuvering radar target detection based on a Markov motion model

To detect highly maneuvering radar targets in low signal-to-noise ratio conditions, a hybrid long-time integration method is proposed, which combines Radon-Fourier Transform (RFT), Dynamic Programming (DP), and Binary Integration (BI), named RFT-DP-BI. A Markov model with unified range-velocity quantification is formulated to describe the maneuvering target’s motion. Based on this model, long-time hybrid integration is performed. Firstly, the whole integration time is divided into multiple time segments and coherent integration is performed in each segment via RFT. Secondly, non-coherent integration is performed in all segments via DP. Thirdly, 2/4 binary integration is performed to further improve the detection performance. Finally, the detection results are exported together with target range and velocity trajectories. The proposed method can perform the long-time integration of highly maneuvering targets with arbitrary forms of motion. Additionally, it has a low computational cost that is linear to the integration time. Both simulated and real radar data demonstrate that it offers good detection and estimation performances.     

基于PAM-CRASH的蒙皮典型结构高速冲击仿真

以典型蒙皮结构为研究对象，分别对由2024－T3铝合金和碳纤维复合材料交替层压而成的FMLs以及2024－T3铝合金蒙皮进行高速冲击有限元仿真，并进行了损伤对比。其中，铝合金层和碳纤维层均采用最大应变准则。利用碰撞模拟分析软件PAM-CRASH以及采用SPH弹体对冲击模型进行仿真，结果显示在相同冲击能量下，加了支承结构的蒙皮在损伤抗性方面有了明显提升，并在此基础上分析不同的纤维铺层角度和铺层方式对FMLs蒙皮性能的影响。     

双框架飞机蒙皮检测机器人切换运动控制方法

针对一种双框架飞机蒙皮检测机器人,通过分析该机器人在飞机表面上的受力情况,在飞机表面该机器人受到了非完整约束,基于牛顿-欧拉法建立了机器人非完整约束动力学模型。根据机器人机械结构和运动步态分析,将该非完整机器人系统分为子系统A和子系统B。为了实现机器人在飞机表面运动,采用反演技术和快速Terminal滑模控制相结合的思想对系统设计了控制器,提出了一种反演-滑模控制方法;对于非完整机器人子系统A和子系统B,设计了一种基于事件驱动的切换策略,实现了机器人对期望轨迹的全局渐近跟踪,并利用Lyapunov稳定性证明系统的跟踪误差收敛。仿真和试验表明,采用该切换策略和反演-滑模控制方法,双框架飞机蒙皮检测机器人可以在飞机表面自由运动并进行损伤检测,具有良好的可靠性和稳定性。     

Multi-mode diagnosis of a gas turbine engine using an adaptive neuro-fuzzy system

Gas Turbine Engines (GTEs) are vastly used for generation of mechanical power in a wide range of applications from airplane propulsion systems to stationary power plants. The gas-path components of a GTE are exposed to harsh operating and ambient conditions, leading to several degradation mechanisms. Because GTE components are mostly inaccessible for direct measurements and their degradation levels must be inferred from the measurements of accessible parameters, it is a challenge to acquire reliable information on the degradation conditions of the parts in different fault modes. In this work, a data-driven fault detection and degradation estimation scheme is developed for GTE diagnostics based on an Adaptive Neuro-Fuzzy Inference System (ANFIS). To verify the performance and accuracy of the developed diagnostic framework on GTE data, an ensemble of measurable gas path parameters has been generated by a high-fidelity GTE model under (a) diverse ambient conditions and control settings, (b) every possible combination of degradation symptoms, and (c) a broad range of signal to noise ratios. The results prove the competency of the developed framework in fault diagnostics and reveal the sensitivity of diagnostic results to measurement noise for different degradation symptoms.