Tear Resistance of Orthogonal Kevlar-PWF-reinforced TPU Film

This work seeks to investigate the notch sensitivity and fracture behaviour of orthogonal Kevlar-plain woven fabric (PWF)-reinforced thermoplastic polyurethanes (TPU) film applied to high altitude balloon. Four types of specimens are implemented to measure notched strength and fracture toughness by conducting static tension and tear tests on an MTS system respectively. The damage and failure mechanisms are discussed and the results for notched strength and tear resistance are evaluated and compared with each other. From the experiments, it is found that the notch sensitivity of the film increases with the increase in the size of the hole, but the notch sensitivity and the stress concentration of the notch are insignificant and there is a decrease of only about 4%-10% in tensile strength for the notched specimens with different hole sizes in diameter compared with the unnotched specimen. In contrast, the tear resistance containing a central slit with only 1 mm length is about half of tensile strength of the unnotched film, which implies that the tear resistance exists an significant notch sensitivity. The results of this study provide an insight into notch sensitivity and fracture behaviour of the Kevlar-PWF-reinforced TPU film and constitute a fundamental basis for the design of high altitude balloon.     

帆板控制系统设计

该帆板控制系统采用塑料薄膜电位器作为传感器检测角度信号,检测到的角度信号经信号处理电路送12位的串行接口A/D转换器ADS7818进行数字化转换,转化结果由Cortex-M3处理器LM3S615进行处理产生PWM控制信号,该控制信号经功率VMOS驱动电路实现轴流电扇的速度调节,从而实现帆板角度定位闭环控制。通过按键可以实现帆板角度的设定及运行控制,设置六位LED数码管显示实现角度及其它运行状态的显示。经过实际测试该系统完全达到了设计要求的各项指标要求。     

突片作用下气膜冷却效率的试验研究

为了研究突片对气膜冷却的影响规律, 设计了3种不同堵塞比的等边三角形突片, 并对其对气膜冷却特性的影响规律进行了实验研究.研究结果表明, 与无突片的气膜冷却相比, 突片的存在提高了气膜冷却效果;冷却效率随吹风比的增加而增大, 且沿气流方向冷却效率存在一极大值;当吹风比M<1.5时, 冷却效率随吹风比的增加而增大;当M>1.5时, 冷却效率随吹风比的增加而减小.      

气体动压轴承-转子动力系统稳定性及分岔

基于非线性动力学理论, 研究了普通圆柱型径向气体动压轴承支承的转子动力系统的运动稳定性和分岔.建立了气体动压轴承-Jeffcott转子系统的力学模型, 并采用有限元方法逼近非定常气体雷诺方程, 得到任意时刻的气膜力;数值模拟该非线性动力系统的长期行为, 得到了轴颈中心的运动轨迹;并采用轨迹图、相图、分岔图以及功率谱等, 研究了系统的非线性行为以及不平衡响应的稳定性.研究结果表明:该方法对气体轴承中存在的气膜涡动问题能够给予合理的解释.      

基于伴随非等温射流理论的缝槽气膜冷却模型

在伴随非等温射流基础上发展了一种适用于缝槽气膜冷却绝热温比预估的数学模型.通过合理假设推导出二维壁面射流混合层核心温度分布规律,将其作为气膜绝热壁温,并考虑缝槽几何特征参数和气膜吹风比对冷却效率的影响,得到绝热温比计算公式.用试验数据对该预估模型进行拟合分析,得到了与试验数据拟合精度在±8%以内的半经验预估模型,证明该模型的可行性和应用潜力,并需要更多的试验数据对其进行验证和改进.      

燃气轮机滚动轴承故障模式及延寿方法

分析了燃气轮机滚动轴承常见的10种故障模式及其产生原因,研究了相应的延寿方法及其延寿机理。     

某重型燃气轮机放气活门及排气管路的改进设计

针对某重型燃气轮机放气系统放气活门在结构设计上存在的问题,经过分析和论证,提出了改进方案,通过计算验证了该方案可以实施。     

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

中心进气转静盘腔的流量分配特性试验

采用实验方法, 对具有中心进气、两个出口的盘腔系统的流动特性进行了研究.获得了静盘与转盘间隙以及转盘外缘小孔的冷气流量.结果表明:盘面出流孔的流量随总流量或转速的增加而增加, 该流量与总流量的流量比随总流量的增加而降低, 随着转速增加而增加.盘面出流孔数量为原出流孔数量的一半时, 流出流量也近似是原流出流量的一半.      

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.