大厚度比零件（外侧）和波纹管（内侧）的缝焊研究

某重点型号波纹管组合件的设计要求是缝焊，对照以往产品的结构，比较明显的情况是波纹管在零件的内侧。零件的厚度是3mm，波纹管的厚度是0.1mm，零件与波纹管的厚度比比较大。波纹管在零件的内侧会产生一个问题：波纹管在焊接过程中会逐渐收缩，到最后与零件之间产生间隙，导致局部形不成焊缝。研究通过减小车配间隙,增加冷却手段、滚轮厚度和压力等措施来实现大厚度比的零件和波纹管之间的缝焊。     

Study of GNSS-measured ionospheric total electron content variations generated by powerful HF-heating

The purpose of this work is to report the experimental evidences for the influence of perturbations in the electron density in the dayside mid-latitude ionosphere, that are caused by high-frequency heating of the F2 layer, on the GNSS signals. The experiments were carried out at the Sura heater (Radio Physical Research Institute, N. Novgorod). During the sessions of ionospheric heating with different time modulations of the radiated power the rays linking the navigational satellites with the ground receiver intersected the heated region. Variations in the total electron content (TEC) were studied; these variations are proportional to the reduced phases of navigational signals. It is shown that with the square-wave modulation of the radiated power (with periods of 1, 6, 10 and 15 min), perturbations with periods of the main modulation of heating and its harmonics appear in the spectrum of TEC variations. Examples are presented of identification of the heating-induced variations in TEC, including determination of the amplitudes and time characteristics of these variations.     

Suggestion for aircraft flying qualities requirements of a short-range air combat mission

Owing to the lack of a direct link with the operations in short-range air combat,conventional aircraft flying qualities criteria are inappropriate to guide the design of a task-tailored flight control law.By applying the mission-oriented flying qualities evaluation approach,various aircraft with different control law parameters are evaluated on a ground-based simulator.This paper compares the evaluation results with several conventional flying qualities criteria,and discusses the appropriate parameter combination to reflect the flying qualities requirements of short-range air combat,The comparison and analysis show that a short-range air combat mission requires a higher minimum short period mode natural frequency and a smaller maximum roll mode time constant,and allows a lower minimum pitch attitude bandwidth and a higher maximum short period mode damp ratio than those of conventional flying qualities criteria.Furthermore,a combination of the pitch attitude bandwidth,the pitch attitude magnitude at the bandwidth frequency,and the pitch attitude transfer function gain can define the flying qualities requirements of short-range air com bat.The new metric can successfully predict the flying quality levels of aircraft in a short-range air combat mission.     

浅议信息时代高校校报的发展

在以网络为代表的新媒体无孔不入的今天,传统的报纸面临着巨大的压力,同样新媒体对高校校报的冲击无疑也是巨大的。如何在竞争激烈的新媒体时代继续引领校园舆论,是所有高校校报人所引以深思的问题。列举了信息时代以网络为核心的新媒体对高校校报的冲击,特别是在读者获取信息的方式、读者阅读兴趣、读者阅读习惯等方面的巨大影响;分析了高校校报和网络媒体在内容、形式等方面各自的长处和特点,并初步提出了高校校报机构调整和加深内涵建设等应对措施。     

Air route network optimization in fragmented airspace based on cellular automata

Air route network optimization,one of the essential parts of the airspace planning,is an effective way to optimize airspace resources,increase airspace capacity,and alleviate air traffic con gestion.However,little has been done on the optimization of air route network in the fragmented airspace caused by prohibited,restricted,and dangerous areas (PRDs).In this paper,an air route network optimization model is developed with the total operational cost as the objective function while airspace restriction,air route network capacity,and non-straight-line factors (NSLF) are taken as major constraints.A square grid cellular space,Moore neighbors,a fixed boundary,together with a set of rules for solving the route network optimization model are designed based on cellular automata.The empirical traffic of airports with the largest traffic volume in each of the 9 flight information regions in mainland China is collected as the origin-destination (OD) air port pair demands.Based on traffic patterns,the model generates 35 air routes which successfully avoids 144 PRDs.Compared with the current air route network structure,the number of nodes decreases by 41.67％,while the total length of flight segments and air routes drop by 32.03％ and 5.82％ respectively.The NSLF decreases by 5.82％ with changes in the total length of the air route network.More importantly,the total operational cost of the whole network decreases by 6.22％.The computational results show the potential benefits of the model and the advantage of the algorithm.Optimization of air route network can significantly reduce operational cost while ensuring operation safety.     

强不确定系统“全系数之和等于1”的实现方法

摘要： 研究强不确定系统“全系数之和等于1”的实现方法，强不确定系统指的是系统的静态增益及其界不完全确知且范围较大.“全系数之和等于1”是吴宏鑫院士20世纪80年代发现的，该原理表明，对于未知连续系统，其离散化系统的系数的和在一定条件下是1.该原理的发现对于解决闭环辨识和自适应控制的瓶颈问题具有关键作用.“全系数之和等于1”是在一定条件下成立的.为了实现系统的“全系数之和等于1”，需要对系统进行一定的变换，以满足所需条件.其中，采用静态增益的标称值的倒数进行输入变换的方法在实际中得到了广泛应用.但是，当系统的不确定性较大时，该变换将带来较大偏差.针对该问题开展了深入研究，明确给出了系统静态增益的不确定性与标称值的比值的关系对于实现“全系数之和等于1”的影响.当不确定性与标称值的比值较小时，可以近似实现“全系数之和等于1”；当比值较大时，进一步给出了通过选取合适的采样周期，近似实现“全系数之和等于1”的方法.本文的研究对于特征模型理论在实际中的应用提供了一定的基础.     

基于Visual Basic的互感器负荷箱测量仪校准系统的实现

为解决互感器负荷箱测量仪同相分量和正交分量的校准问题,在分析互感器负荷箱测量仪工作原理的基础上,设计了基于电子/电工组合式的互感器负荷箱测量仪校准装置,并简要说明装置电工部分、电子部分以及上位机软件的实现。经省级计量研究院验证结果表明,该装置校准结果符合0.2级要求,可作为标准装置解决1级互感器负荷箱测量仪量值溯源问题。     

飞机数字化装配系统中机身交点孔加工方法研究

针对传统交点孔加工方法加工精度低且存在回弹变形的问题,设计了一种满足飞机大部件数字化装配要求的机身交点孔精加工方法,根据交点孔的加工特性完成了机身定位与固持、数控加工中心定位以及加工工艺的总体设计,确定了交点孔加工程序原点的计算方法和编程原则,最后通过交点孔试切加工试验验证了加工方法的可行性。     

Application of small-size antennas for estimation of angles of arrival of HF signals scattered by ionospheric irregularities

A modification of the Doppler Interferometry Technique is suggested to enable estimating angles of arrival of comparatively broadband HF signals scattered by random irregularities of the ionospheric plasma with the use of small-size weakly directional antennas. The technique is based on the measurements of cross-spectra phases of the probe radiation recorded at least in three spatially separated points. The developed algorithm has been used to investigate the angular and frequency-time characteristics of HF signals propagating at frequencies above the maximum usable one (MUF) for the direct radio path Moscow-Kharkiv. The received signal spectra show presence of three families of spatial components attributed, respectively, to scattering by plasma irregularities near the middle point of the radio path, ground backscatter signals and scattering of the sounding signals by the intense plasma turbulence associated with auroral activations. It has been shown that the regions responsible for the formation of the third family components are located well inside the auroral oval. The drift velocity and direction of the auroral ionosphere plasma have been determined. The obtained estimates are consistent with the classical conception of the ionospheric plasma convection at high latitudes and do not contradict the results of investigations of the auroral ionosphere dynamics using the SuperDARN network.     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.