涡轮叶片表面气膜冷却效率的实验研究

采用放大的叶片模型，利用大尺寸低速线性叶栅风洞进行实验，测量了涡轮导向叶片表面不同位置单排气膜孔的气膜冷却效率，研究了孔排位置、吹风比及来流雷诺数的影响。风洞实验段由3个叶片组成，其中中间的叶片为试验叶片，由优质木材制成。试验叶片表面上开有15排气膜孔，其中吸力面3排，前缘区6排，压力面6排。实验的参数变化范围是：基于叶片弦长的来流雷诺数250000-450000，吹风比0．5-2．5。结果表明，由于气膜孔排位置的不同，其下游冷却效率受来流雷诺数及吹风比影响的变化趋势也有所不同。     

穿透式冷板的传热分析

对航空电子设备上采用的空心冷板冷却系统的传热特性进行了分析求解，得到了空心冷板稳态温度分布表达工和功率－温度－流量关系式，可作为空心冷板系统的设计依据，建立了空心冷板失效的动态温度模型，得到的温度－时间响应特性可用于评估冷板系统耐热冲击性能。     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

大型双曲冷却塔表面脉动风压随机特性——风压极值探讨

针对风压信号呈现的非高斯特性和传统极限估计方法的局限,首次提出基于保证率和相关性的极值估计方法——全概率迭代法进行冷却塔表面脉动风荷载极值分析,并和传统的峰值因子法及改进的Sadek-Simiu法计算结果进行对比验证。结果表明：全概率迭代法避开了对随机过程的高斯分布假定,相比传统的极值估计方法其结果更加真实可靠;表达风压极值中脉动分量的峰值因子数值沿着环向和子午向变化显著,如取为同一数值则偏于危险或过于保守;采用全概率迭代法得到的表面风压系数极值分布曲线与规范取值相比,迎风面和负压峰值区域极值偏小,背风区域极值偏大,且最小值对应角度相差约10°。     

AIRCRAFT CONCEPT EVALUATION AND EFFECTIVENESS-BASED DECISION-MAKING

Based on effectiveness analysis, a novel method is presented for combat aircraft top-hierarchy concept evaluation and decision-making. Applying multi-criterion decision-making （MCDM） and analytic hierarchy process, the new method can help to overcome the limitations of existing evaluation systems and decision-make methods. The proposed method includes the following process~ （1） Establish a multi-criterion and multi-hierarchy evaluation attribute system by introducing combat effectiveness~ （2） Assign weight to the attributes and normalize them; （3） Evaluate and decision-make top-hierarchy aircraft concept based on effectiveness to reach a satisfactory design by comprehensively applying four multi-criterion decision-making methodologies, i.e. grey correlation pro- jection method, weighted summation method, weighted quadrature method and ideal solution decision-making method, while considering the attribute hierarchy system and the logical relations among the attributes. Finally, an example is given to indicate the validity and feasibility of the proposed method.     

基于RS-485的飞机液冷附件维修检测台监控系统

飞机液冷附件维修检测台可模拟飞机液冷回路运行状态，同时监控流量、压力及温度，集实验、检测、维修为一体。本文介绍了一款基于RS-485通信网络搭建的飞机液冷附件维修检测台监控系统的主要构成及运行状况。     

声强测量的有效性分析及其在国产轻型飞机上的应用

本文对声强测量的有效性作了较全面分析，为精确的声测量奠定了基础。分析结果应用于某型飞机的声强测量中，为该型飞机的降噪工作提供了可靠的数据来源。     

复杂可修系统效能中可信度矩阵的构造方法

复杂可修系统可信度建模对保证效能的定量分析至关重要.本文在考虑不同维修状况的基础上,着重对不同任务剖面内相应任务阶段中武器装备可信度进行了深入的定量分析和综合,进而构造出武器装备的可信度矩阵,用于武器装备的效能分析;文中以某地面车辆为例,进一步论证了武器装备可信度矩阵的工程含义,旨在为合理确定一大类武器装备的效能和可信度指标提供理论依据.     

ISAR欺骗干扰效果评估方法研究

逆合成孔径雷达（ISAR）能够获取运动目标的一维像和二维像,利用宽带特征识别出真实空间目标.宽带成像欺骗干扰是对抗ISAR雷达目标识别的有效措施.构建了基于目标结构特征的ISAR欺骗干扰效果评估体系,提出了相应的干扰效果评估准则,研究了ISAR欺骗干扰效果评估方法.利用仿真评估软件进行仿真分析,验证了评估方法的合理性.