Thermal-structural analysis of regenerativelycooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Struc tural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter γ3 =0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when γ3 ＞ 0.The results of sen sitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.     

基于博弈论的自由空战指挥引导对策问题研究

博弈论是解决空战对抗问题的有效方法之一,针对目前自由空战筹划困难、指挥引导对策单一的现状,在现有空战博弈问题研究的基础上,扩展了机动动作库和控制参数,加入了雷达开机时机这一关键决策,分别从静态博弈和动态博弈角度出发,提出了构建自由空战指挥引导对策模型的思路,为下一步指挥引导对策模型的研究奠定了基础.     

突片作用下气膜冷却效率的试验研究

为了研究突片对气膜冷却的影响规律, 设计了3种不同堵塞比的等边三角形突片, 并对其对气膜冷却特性的影响规律进行了实验研究.研究结果表明, 与无突片的气膜冷却相比, 突片的存在提高了气膜冷却效果;冷却效率随吹风比的增加而增大, 且沿气流方向冷却效率存在一极大值;当吹风比M<1.5时, 冷却效率随吹风比的增加而增大;当M>1.5时, 冷却效率随吹风比的增加而减小.      

基于多智能体的多机型协同作战决策系统模型研究

多机型协同作战决策系统开发是一项很复杂的工程,各组成要素之间的活动很难进行定量分析和描述,战场情况也复杂多变,具有不可预见性和不可再现性。文中基于目前多机协同作战仿真的发展现状,运用多智能体(Multi-agent)技术,提出了多机型协同作战复杂系统分析与设计决策仿真模型;介绍了运用群建模和开发工具对基于Multi-agent的多机型协同作战决策系统仿真的实现。     

基于伴随非等温射流理论的缝槽气膜冷却模型

在伴随非等温射流基础上发展了一种适用于缝槽气膜冷却绝热温比预估的数学模型.通过合理假设推导出二维壁面射流混合层核心温度分布规律,将其作为气膜绝热壁温,并考虑缝槽几何特征参数和气膜吹风比对冷却效率的影响,得到绝热温比计算公式.用试验数据对该预估模型进行拟合分析,得到了与试验数据拟合精度在±8%以内的半经验预估模型,证明该模型的可行性和应用潜力,并需要更多的试验数据对其进行验证和改进.      

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

The role of AVDR in linear cascade testing

Linear cascade testing plays an important role in the research and development of turbomachinery and is widely used over the world.The ideal cascade model of a turbomachinery blade row is two-dimensional.In actual linear cascade testing, the flow through the test section converges due to the development of the boundary layer and secondary flow along the sidewall surfaces of the test section.Axial velocity density ratio(AVDR) is adopted to account for the deviation of the tested cascade flow from the ideal 2D model.Among numerous published cascade works, the influence of AVDR on cascade performance is seen to be complicated with many affecting factors, such as those related to cascade/blade geometry and flow conditions.Also, controlling AVDR is limited by the facility capability.Furthermore, real blade-to-blade flow in turbomachines is usually associated with AVDR greater than unity due to limited span of blades between the hub and shroud such that cascade testing without reducing AVDR could be favored sometimes.All these facets add complexity and diversification to the matter.The current paper reviews previous studies and results on AVDR.Consolidated understanding on the role of AVDR and recommendations on how to deal with it in linear cascade testing are provided.      

柔性扑翼微型飞行器升力和推力机理的风洞试验和飞行试验

为探讨柔性扑翼微型飞行器产生升力和推力的机理,在研究考虑柔性大变形扑翼气动力计算方法基础上,利用南京航空航天大学低速风洞进行了不同扑动频率、迎角、速度下微型扑翼升力、推力的变化和动态流场显示等风洞实验,并与计算结果进行了比较分析,为微型扑翼机的设计提供了的参考依据.自行研制的微型柔性结构扑翼机成功地进行了飞行试验.      

改进的翼型积冰数值模拟方法

基于微团概念,以雨滴运动的基本假设出发,对翼型积冰的拉格朗日方法进行了改进.新方法克服了原方法计算效率低、冰形同雨滴分布密度及网格密度相关的缺点,继承了原方法的鲁棒性,不存在欧拉方法的收敛性问题.为验证方法的正确性,计算了NACA0012翼型在0°和4°攻角下的霜冰积冰情况、表面水收集量和局部撞击系数.结果表明新方法减少了计算量,预测的冰形和实验结果一致,并分析了积冰对气动性能的影响.      

遗传算法在飞机着陆调度问题上的应用

用遗传算法对飞机着陆调度问题的两个方面:队列顺序的确定和跑道指派进行了研究.队列顺序采用飞机编号的单一整数染色体编码方案,配合相应的变异、交叉算子,避免了后代非法解的问题.跑道指派则在适值函数计算中,基于对列最短的原则来加以确定,避免了对队列顺序和跑道指派进行分别编码.算例研究了单跑道与双跑道两种情况.计算结果表明,这种编码方案以及变异、交叉算子对这一问题具有很好的效果,可在普通PC机上实现雷达扫描周期内的实时计算要求.