地面燃气轮机单管燃烧室流量分配试验

对设计的100kW地面燃气轮机单管燃烧室空气流量分配进行了试验研究。在常压环境下采用堵孔法分别得到了旋流器、主燃孔和掺混孔的流量特性曲线,分析得到燃烧室不同结构的流量系数;试验研究了不同进口流量条件下燃烧室的流量分配,测量得到了燃烧室总压损失。研究发现:随着进口空气流量的增加,燃烧室的流量分配比例基本保持稳定,并且与燃烧室的设计空气比例基本吻合;随着燃烧室进口流量（雷诺数）的增加,旋流器、主燃孔和掺混孔的流量系数呈线性降低;随着进口流量（雷诺数）的增加,燃烧室总压损失逐渐增大;对主燃孔和掺混孔的流量特性测量中,两种测量方法得到的试验结果稍有差别,总体上看两种测量方法的试验结果较为接近。通过对比分析证明两种试验测量方法真实可靠,该研究结果可为100kW地面燃气轮机燃烧室的设计与优化提供依据。      

当量油气比对内燃波转子燃烧特性的影响

为了研究当量油气比对内燃波转子燃烧特性的影响规律,采用控制变量法,保持内燃波转子转速、混气填充速度不变,通过调节燃料喷射体积流量改变混气的当量油气比。在不同的当量油气比下开展内燃波转子燃烧特性试验。试验结果表明:当量油气比对于内燃波转子燃烧过程影响很大,随着当量油气比的增加,内燃波转子获得的燃烧压力增益增大,在内燃波转子转速为900r/min、混气填充速度为6.741m/s、当量油气比为1.442时,6个工作循环内平均燃烧压力增益达到246.29％,火焰平均传播速度随当量油气比呈类似正态分布,在化学恰当比附近达到最大10.8m/s。当量油气比小于1时,两组工况下火焰锋面呈向下倾斜状传播,当量油气比大于1时,两组工况下火焰锋面呈向上倾斜状传播。      

激波引燃冲压发动机一体化流场数值模拟

激波引燃冲压发动机是一种采用爆轰形式组织燃烧的吸气式高超声速飞行器动力系统。采用AUSMPW+迎风格式、氢氧7组分8步基于反应模型,在非结构网格离散域上求解二维多组分化学非平衡流Euler方程。采用发展的数值方法求解了激波引燃冲压发动机内外一体化流场,研究了台阶长度、斜劈尖角度对发动机流场结构和发动机性能参数的影响规律。计算结果表明,所发展的数值方法能用于激波引燃冲压发动机的一体化流场和性能预示计算;台阶长度和斜劈尖角度影响发动机流场结构和预混气体能量释放程度。推力和燃料比冲均随台阶长度的增大而增大,随斜劈尖角度的增大而减少。     

低雷诺数下离心压气机性能及流动影响的数值研究

对高空低雷诺数条件下低压离心压气机进行了全三维数值模拟,分析了雷诺数对其内部流场的影响.结果表明:随着雷诺数降低,离心压气机的效率、裕度和流通能力下降;影响叶片表面负荷分布,使得转子叶片的做功能力下降;叶片前缘分离区范围增大,二次流增强,分流叶片叶尖泄漏损失增大,主叶片吸力面通道的低速区明显增大,起始位置也向前移动,对展向的影响区域也随之增加.      

乙烯和汽油多循环脉冲爆震发动机起爆特性比较

为了研究脉冲爆震发动机(PDE)结构对其工作性能的影响,在内径为40mm、长为1050mm的气动阀式脉冲爆震发动机样机上,进行了气态乙烯/空气和液态汽油/空气的多循环起爆特性试验研究.研究结果表明:在25,30Hz和40Hz下都能在乙烯/空气中成功触发爆震波,40Hz下产生C-J(Chapman-Jouguet)爆震波,传播速度为1724m/s(低于C-J爆震波速度理论值1832.45m/s的5.6%),峰值压力为3.01MPa(高于C-J爆震波压力理论值2.79MPa的7.88%).在相同结构下,汽油/空气未能完成由缓燃向爆震转变的过程.通过对比两种燃料下的试验结果发现:相对于气态燃料,液态燃料受其蒸发过程的影响,在爆震管内的火焰加速缓慢,需要更多的强化燃烧装置来加速火焰,带来的总压损失也更大.因此,对于液态燃料改善雾化和蒸发,提高可爆混气的质量是其实现低阻起爆的关键.      

数值研究低热值燃料环管燃烧室燃烧流场

在任意曲线坐标系下对采用两种不同组分(天然气掺混氮气、一氧化碳)的低热值燃料环管燃烧室燃烧流场进行计算,结果表明低热值燃料的化学反应速率与其组分直接有关,燃料一氧化碳的燃烧效率高于天然气与氮气掺混物燃料,燃料组分变化对燃烧室燃烧效率与出口温度影响很大,因此选用合适的燃料十分重要.计算所得的燃烧室的燃烧效率和出口温度分布与试验数据符合较好,表明所用的数学模型与计算方法合理,计算程序可靠,可为低热值气体燃料燃烧室研制和优化设计提供有用的数据.      

Flow Stability Model for Fan/Compressors with Annular Duct and Novel Casing Treatment

A three-dimensional compressible flow stability model is presented in this paper, which focuses on stall inception of multi-stage axial flow compressors with a finite large radius annular duct configuration for the first time. It is shown that under some assumptions, the stability equation can be obtained yielding from a group of homogeneous equations. The stability can be judged by the non-dimensional imaginary part of the resultant complex frequency eigenvalue. Further more, based on the analysis of the unsteady phenomenon caused by casing treatment, the function of casing treatment has been modeled by a wall impedance condition which is included in the stability model through the eigenvalues and the corresponding eigenfunctions of the system. Finally, some experimental investigation and two numerical evaluation cases are conducted to validate this model and emphasis is placed on numerically studying the sensitivity of the setup of different boundary conditions on the stall inception of axial flow fan/compressors. A novel casing treatment which consists of a backchamber and a perforated plate is suggested, and it is noted that the open area ratio of the casing treatment is less than 10%, and is far smaller than conventional casing treatment with open area ratio of over 50%, which could result in stall margin improvement without obvious efficiency loss of fan/compressors.     

Experimental Investigation of Nozzle Effects on Thrust and Inlet Pressure of an Air-breathing Pulse Detonation Engine

Nozzle effects on thrust and inlet pressure of a multi-cycle air-breathing pulse detonation engine (APDE) are investigated experimentally. An APDE with 68 mm in diameter and 2 050 mm in length is operated using gasoline/air mixture. Straight nozzle, converging nozzle, converging-diverging nozzle and diverging nozzle are tested. The results show that thrust augmentation of converging-diverging nozzle, diverging nozzle or straight nozzle is better than that of converging nozzle on the whole. Thrust augmentation of straight nozzle is worse than those of converging-diverging nozzle and diverging nozzle. Thrust augmentations of diverging nozzle with larger expansion ratio and converging-diverging nozzle with larger throat area range from 20% to 40% on tested frequencies and are better than those of congeneric other nozzles respectively. Nozzle effects on inlet pressure are also researched. At each frequency it is indicated that filling pressures and average peak pressures of inlet with diverging nozzle and converging-diverging nozzle with large throat cross section area are higher than those with straight nozzle and converging nozzle. Pressures near thrust wall increase in an increase order from without nozzle, with diverging nozzle, straight nozzle and converging-diverging nozzle to converging nozzle.     

旋转激光陀螺惯导系统误差传播特性分析

设计旋转式惯导系统(INS, Inertial Navigation System)最重要的工作是理清旋转调制误差自动补偿机理、掌握补偿前后误差的传播特性,在此基础上设计合理的转位方案,并对其进行仿真和试验验证.结合单轴旋转式惯导系统工作原理和误差传播方程,解释了旋转调制误差自动补偿的机理,利用理论和仿真两种手段分析了单轴旋转惯导系统中惯性元件常值误差、随机误差、标度因数误差和安装误差的传播特性,得到了旋转调制对惯性器件误差的调制效果,验证了单轴正反转停方案的有效性和应用的合理性.研究结果为旋转式激光陀螺(LG, Laser Gyroscope)惯导系统的设计提供了理论参考和设计依据.     

旋转捷联惯导系统原理及典型方案分析

旋转捷联惯导系统采用旋转调制误差补偿技术对陀螺仪和加速度计误差进行调制,可以提高系统导航精度。文章借助捷联系统基本误差方程,简要分析了旋转调制误差补偿的机理;通过对几种典型IMU旋转方案的分析和仿真,验证了旋转调制误差补偿技术的有效性并比较了不同旋转方案的特点。