全文获取类型
收费全文 | 335篇 |
免费 | 56篇 |
国内免费 | 143篇 |
专业分类
航空 | 397篇 |
航天技术 | 52篇 |
综合类 | 50篇 |
航天 | 35篇 |
出版年
2024年 | 3篇 |
2023年 | 9篇 |
2022年 | 13篇 |
2021年 | 19篇 |
2020年 | 13篇 |
2019年 | 21篇 |
2018年 | 17篇 |
2017年 | 31篇 |
2016年 | 27篇 |
2015年 | 30篇 |
2014年 | 23篇 |
2013年 | 20篇 |
2012年 | 33篇 |
2011年 | 29篇 |
2010年 | 30篇 |
2009年 | 30篇 |
2008年 | 22篇 |
2007年 | 15篇 |
2006年 | 18篇 |
2005年 | 9篇 |
2004年 | 10篇 |
2003年 | 16篇 |
2002年 | 18篇 |
2001年 | 8篇 |
2000年 | 6篇 |
1999年 | 11篇 |
1998年 | 5篇 |
1997年 | 2篇 |
1996年 | 4篇 |
1995年 | 5篇 |
1994年 | 13篇 |
1993年 | 4篇 |
1992年 | 3篇 |
1991年 | 4篇 |
1990年 | 7篇 |
1989年 | 3篇 |
1988年 | 3篇 |
排序方式: 共有534条查询结果,搜索用时 625 毫秒
21.
从弹性梁的非线性应变位移关系出发,结合Hamilton变分原理推导出了作大挠度振动的空间梁的动力学有限元方程。方程中考虑了与变形相耦合的非线性惯性项。计算表明,作大挠度振动的悬臂梁的响应是由不同的谐波成分组成;在相同结构阻尼影响下,大挠度梁的稳态振幅比线性情况下的稳态振幅要低;非线性惯性项与弯扭耦合项对系统的动力学特性有比较明显的影响。 相似文献
22.
在已知弧齿锥齿轮齿面网格的条件下,分析了单齿啮合时弧齿锥齿轮齿面弹性变形对轮齿啮合点位置的影响。为此,首先形成一整套刚性齿面啮合点的数值计算方法;然后,采用赫兹接触理论计算齿面弹性变形,确定齿轮轮齿的微小转动及由此引起的啮合点位置的变动。将齿轮因齿面变形而产生微小转角,继而进行齿面啮合分析的过程定义为拟赫兹接触分析。结果表明,齿面弹性变形引起的齿轮轮齿的微小转动对啮合点的最终位置有一定的影响。 相似文献
23.
非均质壁面对液滴俘获能力的数值模拟研究 总被引:1,自引:0,他引:1
为研究不同非均质壁面对液滴的俘获能力,采用界面追踪法(FTM)结合广义滑移边界建立了接触角模型,对液滴在非均匀润湿的非均质壁面上的运动过程进行了数值模拟研究。液滴在倾斜壁面上受到重力作用由均匀润湿部分下滑至非均匀润湿部分,通过改变Bo 数、Oh 数、非均匀润湿程度研究了液滴在非均匀润湿区域的运动规律。研究表明:Bo 数越大,液滴运动受壁面阻力影响越小,液滴下滑的速度越快,液滴越难以被俘获;Oh 数越大,液滴运动受壁面阻力影响越小,液滴越难以被俘获;非均匀润湿程度越大,非均质壁面对液滴的阻力越大,液滴越易被俘获。 相似文献
24.
针对微型惯性开关闭合时间短、接触弹跳问题,设计了增强接触效果的摩擦接触式微型惯性开关。基于MEMS惯性开关工作原理,建立了开关物理模型,研究了不同类型惯性开关的闭合性能,提出了增强接触的摩擦接触方法,设计了摩擦接触式微型惯性开关的结构。为了对比接触性能,基于UV–LIGA叠层光刻和精密微电铸工艺,研制了3种不同类型的惯性开关。最后,进行落锤试验,测试结果显示:施加400g外载加速度时,刚性、柔性、摩擦接触式微型惯性开关的闭合时间分别为10μs、80μs、620μs;在惯性开关中引入摩擦电极,既能延长闭合时间,又能解决弹跳问题。研究结果表明,摩擦接触式微型惯性开关在增强接触效果方面具有很大的优越性。 相似文献
25.
《中国航空学报》2021,34(3):225-240
In this paper, the relative sliding motion between the target and the manipulator’s end-effector is considered and characterized as a unilateral contact constraint. A new possible solution is presented to estimate the inertial parameters of a non-cooperative target while the relative sliding motion exists. First, the detailed analysis of the dynamical model is presented, and a parameter-explicit linear time-varying model is obtained. Then, an extended state observer is constructed based on the new model, which can effectively estimate the unknown inertial parameters of the target when relative sliding motion exists. As the modified reactionless controller requires the knowledge of inertial parameters, a hybrid post-capture control scheme is also established based on the switch law between different controllers. The correctness and efficiency of the proposed algorithm are validated by numerical simulation, which proves a potential framework for the non-cooperative target post-capture operation. 相似文献
26.
考虑气动力非线性的柔性飞机阵风响应分析 总被引:1,自引:0,他引:1
针对大展弦比柔性飞机阵风响应问题,考虑在大攻角(AOA)情况下气动力非线性的影响,通过将修正的Theodorsen方法与片条理论相结合,得到非线性的时域非定常气动力;在此基础上,建立阵风干扰下的大展弦比柔性飞机非线性气动弹性模型,完整地发展了一种新颖的可考虑气动力非线性的大展弦比柔性飞机阵风响应分析方法.结合算例模型开展方法验证和数值仿真,对比翼尖和质心(CG)处阵风附加过载在线性和非线性情况下的变化.算例结果表明,考虑大攻角情况下的气动力非线性后,大展弦比飞机的阵风响应较线性情况有明显变化,翼尖处的阵风附加过载最多可减少41.7%,气动力非线性的影响不可忽视. 相似文献
27.
28.
The method of reliability is proposed for the investigation of thermal contact conductance (TCC) in this study. A new definition is introduced, namely reliability thermal contact conductance (RTCC), which is defined as the TCC value that meets the reliability design requirement of the structural materials under consideration. An experimental apparatus with the compensation heater to test the TCC is introduced here. A practical engineering example is utilized to demonstrate the applicability of the proposed approach. By using a statistical regression model along with experimental data obtained from the interfaces of the structural materials GH4169 and K417 used in aero-engine, the estimate values and the confidence level of TCC and RTCC values are studied and compared. The results show that the testing values of TCC increase with interface pressure and the proposed RTCC model matches the test results better at high interface pressure. 相似文献
29.
30.
分别介绍了接触问题和MLPG(Meshless Local Petrov-Galerkin)混合配点法的理论基础,推导了相关公式,给出了两种典型接触状态的定解条件,使用二维线性基函数,采用三次样条曲线权函数,通过移动最小二乘法插值,将MLPG混合配点法运用到接触分析中,使用罚函数法添加本质边界条件,对二维弹性接触问题的接触过程进行模拟,反复迭代得到真实的接触情况,建立了一种新的应力-位移非线性数学求解模型,结合遗传算法对实际工程接触问题进行了求解优化,给出优化结果和目标函数变化曲线,并与相关文献结果比较,验证了该方法的有效性. 相似文献