非均质壁面对液滴俘获能力的数值模拟研究

为研究不同非均质壁面对液滴的俘获能力,采用界面追踪法（FTM）结合广义滑移边界建立了接触角模型,对液滴在非均匀润湿的非均质壁面上的运动过程进行了数值模拟研究。液滴在倾斜壁面上受到重力作用由均匀润湿部分下滑至非均匀润湿部分,通过改变Bo数、Oh数、非均匀润湿程度研究了液滴在非均匀润湿区域的运动规律。研究表明:Bo数越大,液滴运动受壁面阻力影响越小,液滴下滑的速度越快,液滴越难以被俘获;Oh数越大,液滴运动受壁面阻力影响越小,液滴越难以被俘获;非均匀润湿程度越大,非均质壁面对液滴的阻力越大,液滴越易被俘获。      

基于值域的多约束GNSS单频单历元定姿新算法

多天线增强了全球卫星导航系统（GNSS）单频单历元姿态测量解算模型的强度,但随着天线数量增加,模糊度维数成倍增加,从模糊度域确定搜索空间的计算量将显著增长。基于此,提出了基于值域的多约束多天线GNSS单频单历元姿态测量新算法：该算法将姿态约束融入值域搜索模型,利用姿态约束条件推导搜索步长,通过姿态域三维搜索确定模糊度搜索空间,以基于最优条件姿态解非迭代近似估计的方法固定模糊度。实验结果表明,新算法中模糊度搜索效率较原方法提高约65.8%,固定模糊度效率较标准迭代算法提高约95.3%,且与标准迭代算法性能相当;所提算法能够实现GNSS单频单历元的模糊度固定和载体全姿态测量,具有较高的正确率。     

Inertial parameter estimation and control of non-cooperative target with unilateral contact constraint

In this paper, the relative sliding motion between the target and the manipulator’s end-effector is considered and characterized as a unilateral contact constraint. A new possible solution is presented to estimate the inertial parameters of a non-cooperative target while the relative sliding motion exists. First, the detailed analysis of the dynamical model is presented, and a parameter-explicit linear time-varying model is obtained. Then, an extended state observer is constructed based on the new model, which can effectively estimate the unknown inertial parameters of the target when relative sliding motion exists. As the modified reactionless controller requires the knowledge of inertial parameters, a hybrid post-capture control scheme is also established based on the switch law between different controllers. The correctness and efficiency of the proposed algorithm are validated by numerical simulation, which proves a potential framework for the non-cooperative target post-capture operation.     

基于闭环解析解的可重复使用运载器轨迹在线生成方法

The relationships between path constraints such as heating rate, dynamic pressure and aerodynamic load and velocity during entry flight are analyzed in  r-V  plane for an entry vehicle with mediate high lift to drag ratio. Through derivation and integration, a unified formula for path constraints is obtained in  r-V  plane. Based on the unified formula and several characteristics an analytical solution is obtained,and an online trajectory generation method is developed. In the method, the coupled longitudinal and lateral motion is considered, and can make the best use of flight capability and satisfy path constraints. Trajectory generation cases with different flight mission and downranges are tested. Simulation results demonstrate the capability and efficiency of the trajectory planning method in dealing with path constraints.     

空间真空环境下密封电磁继电器的触点失效研究

密封电磁继电器有其固有的漏率,在应用于空间真空环境下由于气体泄漏使得其内部气体压力逐渐降低,导致继电器的触点在低气压环境下工作失效（负载切换时）。文章选择国产继电器样品对上述机理进行了试验验证,并对继电器内部气体压力与触点电弧失效的规律进行了研究。     

Investigation on Thermal Contact Conductance Based on Data Analysis Method of Reliability

The method of reliability is proposed for the investigation of thermal contact conductance (TCC) in this study. A new definition is introduced, namely reliability thermal contact conductance (RTCC), which is defined as the TCC value that meets the reliability design requirement of the structural materials under consideration. An experimental apparatus with the compensation heater to test the TCC is introduced here. A practical engineering example is utilized to demonstrate the applicability of the proposed approach. By using a statistical regression model along with experimental data obtained from the interfaces of the structural materials GH4169 and K417 used in aero-engine, the estimate values and the confidence level of TCC and RTCC values are studied and compared. The results show that the testing values of TCC increase with interface pressure and the proposed RTCC model matches the test results better at high interface pressure.     

资源约束突变的航天器观测快速重调度优化算法

针对航天器对地观测调度中资源约束发生突变的情况,提出了一种基于蚁群算法的启发式重调度算法。首先对重调度过程中的资源约束进行分析,给出了资源约束发生变化的重调度模型。然后,结合原调度优化结果,给出重调度任务集合更新方法,对任务集合进行剪裁。最终,基于最大限度利用原调度方案信息的思想,结合任务集合更新及优先级等启发式信息,给出了一种改进的重调度优化算法。数值计算结果表明,所设计的算法可以快速有效的提高重调度过程的收益。     

考虑等待时间约束的不完美生产系统的产出优化

针对某些生产系统存在等待时间约束及设备劣化引起产品质量损失这2个问题,构建了系统的缓冲区控制和预防性维护的联合优化模型。首先,利用伽马过程对下游瓶颈工作站的劣化过程进行建模,并考虑由于其状态劣化引起的产品质量损失;其次,在此基础上,将工件的到达、中间缓冲区及下游工作站的加工过程视为一排队系统,引入M/G/1/K排队模型分别求解了在制品(WIP)被阻塞和超出等待时间约束的概率;最后,以最大化系统的"有效产出"为目标,对系统的预防性维护和缓冲区控制作了联合优化。数值实例表明:本文所提模型是切实、有效的,对带等待时间约束的生产系统的缓冲区控制、预防性维护以及产出提高具有一定的指导意义。     

行星轮系动态啮合应力研究

针对行星传动齿轮系的结构特点,建立了行星齿轮和主动齿轮的非线性接触有限元模型,应用AN-SYS软件进行了动态接触分析的研究。基于研究结果,建立了可以体现行星齿轮系在工作过程的啮合应力变化情况的计算模型,可以直观地观察到行星齿轮系从开始啮合到完全脱开整个过程中的应力分布及变化情况。选择20节点六面体单元,模拟齿轮受载情况,迅速、高效地得出整个齿轮系的强度、刚度分布云图,大大提高了设计效率。     

基于MLPG混合配点法的接触问题形状优化

分别介绍了接触问题和MLPG(Meshless Local Petrov-Galerkin)混合配点法的理论基础,推导了相关公式,给出了两种典型接触状态的定解条件,使用二维线性基函数,采用三次样条曲线权函数,通过移动最小二乘法插值,将MLPG混合配点法运用到接触分析中,使用罚函数法添加本质边界条件,对二维弹性接触问题的接触过程进行模拟,反复迭代得到真实的接触情况,建立了一种新的应力-位移非线性数学求解模型,结合遗传算法对实际工程接触问题进行了求解优化,给出优化结果和目标函数变化曲线,并与相关文献结果比较,验证了该方法的有效性.