Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments

In this work, the mechanical properties and electrical conductivity of the extruded 7136 aluminum alloy treated by single-stage aging treatment (T6), retrogression and re-aging treatment (RRA), and multiple retrogression and re-aging treatment have been investigated by means of hardness measurements, electrical conductivity tests and tensile tests. The results have shown that the properties of the 7136 alloy such as hardness, tensile strength and electrical conductivity were sensitive to retrogression time (within 90 min). With prolonging the retrogression time, the tensile strength was enhanced first and then decreased, yet the electrical conductivity was continuously increased. The 60 min-treated alloy performed the highest tensile strength (716 MPa), whereas the 90 min-treated alloy possessed the highest electrical conductivity (33.95%IACS). Compared with the T6-treated alloy, the tensile strength and electrical conductivity were improved by 3.3% and 18.9%, respectively. The electrical conductivity showed an obvious increase with repetitious times of the RRA treatment. After 3RRA60 treatment, a good combination of tensile strength (705 MPa) and electrical conductivity (33.20%IACS) can be obtained. Compared with the T6 condition, the tensile strength and electrical conductivity were improved by 1.7% and 16.3%, respectively. The mechanism of microstructure evolution under different aging treatments has been discussed in detail.     

真空出气对星用聚酰亚胺材料电导率的影响

卫星介质材料在真空环境下的出气有可能对材料本身的介电性能产生显著影响,增加长期服役卫星寿命末期的充放电风险。文章以卫星上常用的聚酰亚胺材料为对象,通过地面90Sr-90Y辐照源加速辐照试验研究了在材料真空出气后其表面充电平衡负电位的变化,并据此计算出材料电导率的变化规律。结果显示,在5 pA/cm2电子辐照强度下,聚酰亚胺样品的电导率随着出气量的增加而明显下降,在总质量损失达到0.5%时,电导率减小一半左右。初步分析了出气导致电导率下降的物理机制。研究结果对卫星寿命末期充放电防护设计有指导意义。     

厚度和环境对复合涂层导电性能的影响

为了给数字化刻铣曲面频率选择表面(FSS)结构的制作和加工提供参考和依据,对比研究了含片状银粉颗粒的聚氨酯基和环氧树脂基2种复合导电涂层的基本性能,并通过环境加速试验,重点研究了温度、湿度以及腐蚀气氛对2种导电涂层的界面强度、微观结构和导电性能的影响.通过电桥法测量涂层表面电阻的变化,并通过扫描电境观察环境试验前后,涂层表面和剖面的微观结构和形貌变化.试验结果表明:聚氨酯基涂层的综合性能优于环氧树脂基涂层;在实验所涉及的参数变化范围内,环境因素对2种涂层与基体的界面结合影响不大,但对其导电性能的影响比较明显.环境因素对导电性能的削弱作用,源于相应过程中导电涂层的微观结构损伤.     

Soybean cultivar selection for Bioregenerative Life Support Systems (BLSSs) – Hydroponic cultivation

Four soybean cultivars (‘Atlantic’, ‘Cresir’, ‘Pr91m10’ and ‘Regir’), selected through a theoretical procedure as suitable for cultivation in BLSS, were evaluated in terms of growth and production. Germination percentage and Mean Germination Time (MGT) were measured. Plants were cultivated in a growth chamber equipped with a recirculating hydroponic system (Nutrient Film Technique). Cultivation was performed under controlled environmental conditions (12 h photoperiod, light intensity 350 μmol m⁻² s⁻¹, temperature regime 26/20 °C light/dark, relative humidity 65–75%). Fertigation was performed with a standard Hoagland solution, modified for soybean specific requirements, and EC and pH were kept at 2.0 dS m⁻¹ and 5.5 respectively.     

MD-140导电胶粘剂性能测试及分析

文章简要介绍了航天器常用导电胶粘剂的成分和功能原理,研究了MD-140 导电胶粘剂的基本性能以及经过温度循环试验、粒子辐照试验后其力学性能、导热性能和导电性能的变化情况。从导电胶粘剂内部结构角度出发,对其性能的环境退化机理进行分析探讨。结果表明:高低温循环试验后,导电胶的黏结性能变强,导电性能变差,导热性能变化不显著;粒子辐照试验后,导电胶的黏结性能和导电性能变差,导热性能变化不显著。     

新型非接触式径向C4D传感器优化设计

基于电容耦合式非接触电导检测(C4D)技术,设计研发了一种新型径向结构的非接触式电导测量传感器。该传感器利用串联谐振的原理,引入电感模块以消除耦合电容对测量的不利影响,扩大了测量范围,提高了测量灵敏度。同时,用仿真与实验相结合的方法对传感器的电极张角进行了优化研究。在5.0、7.5、9.1、10.2和12.0 mm 5种不同内径的管道中进行了电导测量实验,电导测量相对误差均不超过5%,实验结果表明,所设计的新型非接触式径向C~4D电导测量传感器是可行和有效的。     

三维编织复合材料热物理性能的有限元分析

根据三维编织复合材料的细观结构,分别建立了三维四向和五向编织复合材料热物理性能的有限元模型.采用周期性的非绝热温度边界条件和位移边界条件,计算了三维四向和五向编织复合材料的整体等效热传导系数和热膨胀系数,计算结果同已有文献相比与实验值符合得更好.在此基础上,迸一步研究了编织角、纤维体积分数、编织结构等参数对材料热物理性...     

高温空气传输特性对边界层稳定性及转捩预测的影响

为了研究黏度和导热系数对边界层内基本流和流动稳定性的影响,首先通过分析比较Sutherland公式和目前常用的Gupta等人的拟合关系式,建立了高温气体下黏度和导热系数的计算模型,并分别将Sutherland公式和新建立的计算模型应用于7组元化学平衡流的平板模型,在马赫数为10,16和20,飞行高度为30-5km等条件下分别对黏度和导热系数的模型进行比较.计算结果表明:在高温范围内,黏度和导热系数均影响着边界层的基本流、流动稳定性及转捩预测,且两者影响的趋势相反,黏度的增加、导热系数的减小都能使扰动的增长率变大,增长区变宽,转捩位置提前.      

沥青基碳纤维热导率的间接法测量

文摘采用"四探针法"测定6种沥青基碳纤维单丝的轴向电阻率,通过3个经验公式计算得到其热导率,再将计算值与厂商公布值进行对比分析。结果表明:对于热导率600或300 W/(m·K)的碳纤维采用公式λ=1261/ρ计算得到的热导率值与厂商公布值最为吻合,而对于热导率在300~600 W/(m·K)的碳纤维采用公式λ=440 000/(100ρ+258)-295计算得到的热导率值与厂商公布值最为吻合。以此测试值为基础,建立了沥青基碳纤维单丝电阻率与其热导率的函数关系λ=152 740/(100ρ+22)-26,具有更强的普适性。     

火星表面热环境对航天器热控影响分析

火星大气对太阳辐射产生吸收和散射作用,同时还将与火星表面航天器发生对流换热.热设计时难以直接评估对流、辐射和导热三种换热对航天器的影响,从而确定主要的控温途径.在调研火星表面辐射、大气等热环境的基础上,从线性化传热系数和对流辐射比的角度对比分析了辐射、对流和导热对航天器的影响.器表辐射传热系数随光学属性和温度的变化范围...