扩压叶栅叶尖非定常流动的涡动力学机理

为了揭示压气机叶尖区旋涡结构与流动非定常性之间的关联，采用URANS对一亚声速平面扩压叶栅在不同攻角下的流场进行了求解，并借助Q判据提取了叶尖瞬态涡系结构。结果表明：泄漏涡的破碎现象能够通过诱导新的涡结构间接作用于相邻通道的叶尖流动，是导致叶尖流场失稳的关键因素。在-0.3°和+0.7°攻角下，叶尖泄漏涡发生了螺旋破碎，并伴随有非定常诱导涡的出现，诱导涡对相邻叶片载荷的影响使得叶尖泄漏涡发生周期性摆动；在+1.7°攻角下，泄漏涡破碎会导致反流涡的形成，反流涡的输运会给叶片载荷和来流攻角带来非定常扰动，反过来又会作用于泄漏涡的破碎和反流涡的生成，最终表现为一种自维持的非定常流动现象。     

大型客机低速构型高雷诺数风洞腹撑支架干扰数值模拟

风洞到飞行相关性修正是获取现代大型客机低速气动特性的重要手段，通常采用增压提高风洞试验雷诺数，而支架干扰修正是该修正体系的一个关键环节。采用数值模拟研究了增压风洞腹撑的支架干扰，并分析了腹撑对飞机各部件的干扰及其对风洞流场的影响。通过数值模拟与风洞试验对比，表明升力系数相差0.006，阻力系数最大相差0.001 2，俯仰力矩系数最大相差0.01，验证了CFD数值模拟方法的可靠性。CFD计算结果表明：腹撑使得全机升力增加、阻力减小，俯仰力矩增加；腹撑对升力影响的主要部件是机翼，腹撑使得风洞中心以上动压增加，提升上翼面流速，从而增加了机翼的升力；与传统认识不同的是腹撑对阻力影响为负，且主要影响部件为缝翼，原因为缝翼下偏使得法矢分量向前从而减小了阻力；腹撑对俯仰力矩影响的主要部件是机身及平尾。研究结果揭示了腹撑对飞机气动特性影响的量级、主要影响部件及其流场变化，可为支架干扰数据修正及支架优化设计提供参考。所得结论可更好用于支架干扰试验的开展及风洞到飞行数据的修正，具有一定的工程实用性。     

Numerical investigation of flow mechanisms of tandem impeller inside a centrifugal compressor

This study numerically investigated a single stage centrifugal compressor ‘‘Radiver’’ with a wedge diffuser and several tandem-designed impellers to explore the flow phenomena within the tandem impeller and the potential to enhance compressor performance. The results demonstrate that tandem design and clocking fraction (λ_s) significantly affects the compressor performance. The compressor stage with tandem impellers of Series A of boundary layer growth interruption alone are observed to have a widely operating range but efficiency and total pressure ratio penalty compared with that of conventional impeller. The tandem impeller with at least the same impeller efficiency as the conventional design is considered as a critical design criteria so that further modification process based on the flow characteristic of tandem impeller is necessary. In order to restrain the inducer wake and exducer shock losses, parameters modification of blade angle and thickness distributions are necessary and the modified tandem impeller of Series B is obtained. The modified tandem impeller with 25% clocking arrangement shows an 8.45% stall margin increase and maintains the total pressure ratio and efficiency as the conventional design, which proves the potential of tandem impeller to improve compressor stage performance. It is noteworthy that the tandem impellers of Radiver have not shown obviously balanced exit flow field and the fundamental mechanism of stall margin extending of tandem impeller lies on the improved impeller/diffuser matching performance resulting from the incidence angle variation at diffuser inlet.     

民用飞机全机静力试验前机身工况配平载荷设计

民用飞机全机静力试验中由于加载方案复杂,为了简化试验加载数量,传统的配平方案主要保证考核区的加载准确性,对于非考核区的载荷简化到若干加载点上。对于飞机机身这种薄壁结构,非考核区的配平对考核区影响较大。以某飞机前机身严重工况为例,基于飞机全机有限元模型,研究静力试验的载荷配平方案;通过对比分析态载荷与传统试验态配平载荷方案下的内力解,对传统全机静力试验载荷配平方案进行优化。结果表明：优化后的试验态内力解与分析态内力解基本吻合;对于飞机机身薄壁结构,圣维南原理并不适用,全机静力试验的载荷配平要与真实工况受力情况吻合,才能达到试验验证目的。     

基于 Kriging与多点取样算法的压气机特性建模

针对航空燃气轮机流量系数插值建模过程中,获取样本数据时的实验成本较高以及插值模型精度偏低这 2个问题,根据样本点在设计空间中的分布与模型精度的关系,在 Kriging插值模型的基础上,采用把垂距作为设计变量取值标准的取样算法。首先,将样本点与相邻 2点之间连线的垂距与垂距阈值进行比较,筛选出符合条件的数据点,形成候选点集;其次,选用高斯函数判定基础点集和候选点集的相关性;最后,使用该算法筛选后的样本点构建 Kriging插值模型。实验结果表明,该方法使用的样本点为原来数量的 70%左右,并且预测精度得到了提高,该方法是有效可行的。     

脉动背压离心压气机动态特性及稳定性

试验研究了脉动背压对离心压气机动态响应及喘振特性的影响规律。结果表明:脉动背压条件时压气机性能存在明显非定常特征,高频大幅脉动背压和陡峭的压比流量特性均可强化该非定常特征。基于试验结果,提出了脉动背压压气机非定常性能与脉冲特性及运行工况的关联模型。脉动背压导致压气机喘振边界左移,稳定运行范围最高拓宽12.3%。压气机向小流量工况趋近时,脉动背压引起的流场振荡减弱,但喘振所致的流场振荡逐步强化,致使流场振荡强度呈V型变化特征,表明了脉动背压与压气机气动稳定性之间存在耦合关系。研究探明了脉动背压条件对压气机动态响应和喘振特性的影响规律,对帮助真实运行环境压气机设计理论的发展具有重要意义。      

神经网络模型在压气机通流特性分析中的应用

为了解决通流特性分析程序中原始模型对压气机性能预测精度不足的问题,提高压气机通流特性分析过程的可靠性,基于对大量多圆弧叶栅的数值模拟结果建立了压气机叶栅性能数据库,并以该数据库为依托,采用神经网络建模方法建立了压气机叶栅基准损失系数和基准落后角模型。结果显示:两模型对叶栅基准损失系数和基准落后角的预测精度均满足工程应用要求,其精度分别为±0.002和±1°。在对采用神经网络模型的通流特性分析程序校验过程中发现,其无论对压气机整机性能还是对流动细节的预测精度上都获得了显著提高,尤其是在主流区。此外从压气机整体特性上看,基准损失系数和基准落后角精度的提高对非设计工况损失系数和落后角的预测精度影响是积极的。      

Conceptual design and flight test of two wingtip-docked multi-body aircraft

To overcome the drawbacks such as large wing deformations, poor performance encountering gusts, limits in taking off and landing, inconvenience of transportation of High-Altitude Long-Endurance (HALE) Unmanned Aerial Vehicles (UAVs), a new conceptual aircraft called wingtip-docked Multi-Body Aircraft (MBA) has attracted lots of attentions. Aiming to investigate the feasibility of this concept, two UAV models were designed, manufactured and connected by a wingtip-docking mechanism, which only allows the relative roll motion between the two aircraft. The trim solution of the two connected aircraft is firstly obtained by solving the developed nonlinear flight dynamic equations, followed by the stability analysis based on the linearized model. The results show that the connected aircraft is inherently unstable and cannot fly without a reasonable flight control system. A set of Proportional-Integral-Derivative (PID) control laws was then developed and implemented in the two experimental aircraft. The success of the flight tests show that the flight control can effectively eliminate the unstable motion and the wingtip-docked MBA is controllable and feasible.     

Y7-200A飞机自然结冰飞行试验

介绍了Ｙ７－２００Ａ飞机防冰除冰系统,自然结冰飞行试验所需气象专用设备和机场气象条件的选择以及自然结冰的飞行安全。同时还介绍了飞行试验的内容、试验方法及试验结果,并对试验结果进行了分析,试飞结果表明,带自然积冰飞机性能比带模拟冰型的好,自然结冰试验与模拟冰型试验之间的飞机操纵特性没有不可接受的差异,飞机飞行品质良好。可供运输类飞机自然结冰飞行试验时参考。     

液体火箭发动机典型实验室及典型实验概述

在大量文献研究的基础上,概括介绍了目前液体火箭发动机方面的典型实验室和典型实验及几种用于液体火箭发动机喷雾、燃烧和流动测量的先进仪器。为开展新一代液体火箭发动机的实验研究和设计提供参考。