数字化技术在叶轮研制中的应用

本文通过分析归纳建立了一种叶轮数字化建模方法，并利用该方法成功实现了某型叶轮三维模型创建，同时也根据该数字化模型实现了模具数字化设计及其数控加工。     

A cost driven predictive maintenance policy for structural airframe maintenance

Airframe maintenance is traditionally performed at scheduled maintenance stops.The decision to repair a fuselage panel is based on a fixed crack size threshold,which allows to ensure the aircraft safety until the next scheduled maintenance stop.With progress in sensor technology and data processing techniques,structural health monitoring (SHM) systems are increasingly being considered in the aviation industry.SHM systems track the aircraft health state continuously,lead ing to the possibility of planning maintenance based on an actual state of aircraft rather than on a fixed schedule.This paper builds upon a model-based prognostics framework that the authors developed in their previous work,which couples the Extended Kalman filter (EKF) with a first order perturbation (FOP) method.By using the information given by this prognostics method,a novel cost driven predictive maintenance (CDPM) policy is proposed,which ensures the aircraft safety while minimizing the maintenance cost.The proposed policy is formally derived based on the trade-off between probabilities of occurrence of scheduled and unscheduled maintenance.A numerical case study simulating the maintenance process of an entire fleet of aircrafts is imple mented.Under the condition of assuring the same safety level,the CDPM is compared in terms of cost with two other maintenance policies:scheduled maintenance and threshold based SHM maintenance.The comparison results show CDPM could lead to significant cost savings.     

强不确定系统“全系数之和等于1”的实现方法

摘要： 研究强不确定系统“全系数之和等于1”的实现方法，强不确定系统指的是系统的静态增益及其界不完全确知且范围较大.“全系数之和等于1”是吴宏鑫院士20世纪80年代发现的，该原理表明，对于未知连续系统，其离散化系统的系数的和在一定条件下是1.该原理的发现对于解决闭环辨识和自适应控制的瓶颈问题具有关键作用.“全系数之和等于1”是在一定条件下成立的.为了实现系统的“全系数之和等于1”，需要对系统进行一定的变换，以满足所需条件.其中，采用静态增益的标称值的倒数进行输入变换的方法在实际中得到了广泛应用.但是，当系统的不确定性较大时，该变换将带来较大偏差.针对该问题开展了深入研究，明确给出了系统静态增益的不确定性与标称值的比值的关系对于实现“全系数之和等于1”的影响.当不确定性与标称值的比值较小时，可以近似实现“全系数之和等于1”；当比值较大时，进一步给出了通过选取合适的采样周期，近似实现“全系数之和等于1”的方法.本文的研究对于特征模型理论在实际中的应用提供了一定的基础.     

基于Visual Basic的互感器负荷箱测量仪校准系统的实现

为解决互感器负荷箱测量仪同相分量和正交分量的校准问题,在分析互感器负荷箱测量仪工作原理的基础上,设计了基于电子/电工组合式的互感器负荷箱测量仪校准装置,并简要说明装置电工部分、电子部分以及上位机软件的实现。经省级计量研究院验证结果表明,该装置校准结果符合0.2级要求,可作为标准装置解决1级互感器负荷箱测量仪量值溯源问题。     

可控曲率半径的圆柱形叶片逐点绘型方法

针对中低比转速离心泵,根据叶片进出口边界条件,以逐点绘型方法为基础,提出了一种新的曲率半径可控的叶片绘型方法。该方法的主要特点是曲率半径比值可作为设计常量由设计人员根据需要事先给定,随后分析了曲率半径及比例因子对叶片安放角、叶片包角、相对速度及速度矩等的影响。结果表明,不同曲率半径比值下的叶型参数及流动参数变化范围很大,曲率半径比值较大时,节流损失较大,泵扬程较低,曲率半径比值较小时,脱流损失较大,泵效率较低,存在较优的曲率半径比值区间[1.4,2.4],使叶片安放角平滑变化,泵的综合性能较优,在该优化区间内,取较大的曲率半径比值有利于获得较优的汽蚀性能,比例因子为0时叶片安放角的变化较为平稳,可用于开展离心泵的初步设计。     

新一代战斗机非定常流动数值研究综述

新一代战斗机强调超机动能力和强隐身性，其中大攻角下的静态失速、动态失速及内埋弹仓绕流是与高机动和强隐身密切相关的、极具挑战的几类典型的非定常流动，它们对数值方法提出了极高的要求。为了高精度地仿真流场、清楚地揭示流动机理，有效地控制非定常流动，非常有必要发展高精度且高效率的RANS-LES混合方法体系，包含RANS-LES混合方法本身、与RANS-LES混合方法匹配的高精度自适应耗散格式、基准湍流模式、高质量计算网格、高精度时间推进方法、非定常量的统计方法等，具有极强的紧迫性。提出、发展、验证并应用该类方法数值仿真新一代战斗机（包括单独部件、组合体、甚至全机）的非定常流动，数值预测结果与风洞实验数据吻合良好；此类方法可为新型战斗机设计提供理论依据和分析手段。     

微分法在定位误差分析与计算中的应用

介绍了微分法分析计算定位误差的原理和适用范围,通过生产实例分析,证明了该方法在解决多误差因素定位误差分析与计算中的简便与快捷,从而有效简化了复杂定位方案定位误差的分析与计算,提高了夹具的设计效率。     

Is the phenology-based algorithm for mapping deciduous rubber plantations applicable in an emerging region of northern Laos?

Updated information of rubber plantations is essential for assessing socioeconomic and environmental impacts, especially in the emerging region of northern tropics. Here, a phenological method was modified to detect rubber plantations using Landsat Operational Land Imager (OLI) imagery in Phongsaly Province of northern Laos, where it begun a rubber boom in the mid-2000s due to geo-economic cooperation. It highlighted the landscape and pixel differences of deciduous rubber plantations in the tri-temporal phases (i.e., pre-defoliation, defoliation, and foliation) during the dry season due to phenological changes. Six commonly used vegetation indices (VIs), including the Normalized Difference Vegetation Index (NDVI), Enhanced Vegetation Index (EVI), Land Surface Water Index (LSWI), Atmospherically Resistant Vegetation Index (ARVI), Normalized Burn Ratio (NBR and NBR2) derived from OLI imagery during 2013–2016 were compared to determine the most suitable VI for discriminating the phenological differences of rubber plantations from natural forests. Then, the Differences of Normalized Burn Ratio (DNBR) was applied to generate the 30 m map of rubber plantations in 2016, by combining two masks of Landsat-derived forest and suitable elevation for rubber trees cultivation. The resultant map of rubber plantations had a classification accuracy of 93.7% and the Kappa coefficient of 0.848. Our study demonstrated the usefulness of the Landsat-derived tri-temporal phenological DNBR approach in an emerging region of northern Laos, despite requiring more scenes compared with single- and double temporal window methods.     

Plastic wrinkling prediction in thin-walled part forming process:A review

The precision forming of thin-walled components has been urgently needed in aviation and aerospace field. However, the wrinkling induced by the compressive instability is one of the major defects in thin-walled part forming. The initiation and growth of the wrinkles are interac-tively affected by many factors such as stress states, mechanical properties of the material, geometry of the workpiece and boundary conditions. Especially when the forming process involves compli-cated boundary conditions such as multi-dies constrains, the perturbation of clearances between workpiece and dies and the contact conditions changing in time and space, etc., the predication of the wrinkling is further complicated. In this paper, the current prediction methods were summa-rized including the static equilibrium method, the energy method, the initial imperfection method, the eigenvalue buckling analysis method, the static-implicit finite element method and the dynamic-explicit finite element method. Then, a systematical comparison and summary of these methods in terms of their advantages and limitations are presented. By using a combination of explicit FE method, initial imperfection and energy conservation, a hybrid method is recommended to predict plastic wrinkling in thin-walled part forming. Finally, considering the urgent requirements of com-plex thin-walled structures’ part in aviation and aerospace field, the trends and challenges in wrin-kling prediction under complicated boundary conditions are presented.     

基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.