高超音速化学非平衡钝劈绕流数值计算

 自1970年Davis提出粘性激波层方法以来,用数值方法求解高超音速轴对称钝体绕流问题国内外已做了大量工作,但至今仍未见到关于平面问题的计算结果。对于平面问题,虽然方程在形式上比轴对称简单,但由于二维效应,激波层较厚,用文献[2]的方法向下游区推进有困难。另外,在驻点线上采用极限关系式虽能克服方程的奇性,但驻点解对流向步长Δξ有依赖。     

两种镁合金的化学处理

对AZ91D和AM50合金进行化学处理，用SEM和电化学方法来分析化学转化膜的表面形貌及在腐蚀性电解质中的稳定性。结果表明，铬酸盐处理时，AM50合金较AZ91D合金的成膜反应容易进行，成膜均匀，在3．5％NaCI水溶液中耐蚀性能好；而磷酸盐处理时，结果恰恰相反，AZ91D合金转化膜的性能优于AM50合金的膜。     

高超声速三维碳—碳烧浊流场的数值研究

本文针对高超声速再体的烧蚀现象 ,利用简单隐式TVD差分格式和激波捕捉法 ,数值求解三维化学非平衡Navier Stokes方程 ,其中化学模型是碳 碳 (C C)空气化学模型 ,考虑 12个化学组分和 31个化学反应过程 ,研究了C C烧蚀对再入体头部区域的壁面温度和热流分布的影响。为了计算效率和稳定性提出壁面条件显式处理的方法。对再入高度为 6 5km和速度为 8km/s的再入体头部区域烧蚀流场进行了数值模拟 ,用飞行迎角α =0°的计算结果与国外文献进行了比较 ,符合得较好。同时给出了三维小迎角α =5°的计算结果     

基元化学反应一维爆轰波的数值模拟

应用基元化学反应模型对一维氢氧混合气体爆轰波进行数值模拟。采用一端高温高压点火起爆的方式,模拟爆轰波的传播。对一维爆轰波的结构、传播特征以及各个化学组分的变化趋势进行了研究。通过将模拟的结果同国内外的研究结果进行对比,发现了一些规律,为多维爆轰波的数值模拟和脉冲爆轰发动机的研究奠定一定的基础。     

高超声速小钝锥尾流化学非平衡辐射研究

本文主要目的是研究化学非平衡对高超声速小钝锥尾流辐射的影响。计算结果表明：激发发射辐射比化学发光辐射重要，红外辐射比可光辐射重要。结果还表明：由化学非平衡瞬时辐射模型计算求得的ＮＯ５．３μ的辐射能比由局部平衡辐射模型求得的辐射能大３０￣７０％。由此可知，小钝锥尾流的化学非平衡辐射模型对辐射的影响是不能忽略的。     

TC21钛合金的微观组织对力学性能的影响

研究了两相钛合金TC21关于两种不同微观组织(片状组织和网篮组织)的拉伸性能、断裂韧性和疲劳裂纹扩展性能.结果显示:片状组织相比网篮组织有相近的拉伸强度,但塑性较差;两者的韧性相差不大,但增韧机理不同;网篮组织在中低速扩展区的扩展速率和片状组织几乎相同,但在较高速扩展区显示略低的扩展速率;加载方向对两种组织的疲劳裂纹扩展速率基本无影响;和其他钛合金类似,TC21在Paris区存在转折.     

腰形柱壳的有限条元解

本文用考虑了曲率影响的两结线低阶有限板条元分析了腰形柱壳的力学性能这种条元位移参数少,能较好地体现壳体的几何特性。     

A novel surrogate modeling strategy of the mechanical properties of 3D braided composites

In this paper, a surrogate-based modeling methodology is developed and presented to predict the elastic properties of three dimensional (3D) four-directional braided composites. Using this approach, the prediction process becomes feasible with only a limited number of training points. The surrogate models constructed using Finite Element (FE) method and Diffuse Approximation, reduce the computational time and cost for preparing experimental samples. In the FE model, multiscale method is applied to couple the computations of elastic properties at microscale and mesoscale. Subsequently, a parametric study is performed to analyze the effects of the three design parameters on the elastic properties. Satisfactory results are obtained via the surrogate-based modeling predictions, which are compared with the experimental measurements. Moreover, the predictions obtained from surrogate models concur well with the FE predictions. This study orients a new direction for predicting the mechanical properties based on surrogate models which can effectively reduce the sample preparation cost and computational efforts.     

Effects of process parameters on mechanical properties of abrasive-assisted electroformed nickel

A cathode mandrel with translational and rotational motion, which was supposed to obtain uniform friction effect on surface, was employed in abrasive-assisted electroforming for revolving parts with complex profile. The effects of current density, translational speed and rotational speed on the deposit properties were studied by orthogonal test. The tensile strength, elongation and micro hardness value were measured to find out how the factors affected the properties. The optimized results show that changes of current density affect the tensile strength of nickel layer most, while translational speed has the most remarkable influences on both elonga-tion and micro hardness. The low rotational speed affects the properties least. In this experiment, a smooth nickel layer with tensile strength 581 MPa, elongation 17%and micro hardness 248HV is obtained by the orthogonal test.     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。