Mini-TED跨声速气动特性及其增升机理

通过求解二维可压Navier-Stokes方程,研究了NACA0012翼型加装微型后缘增升装置（mini-TED）后的跨声速流场特性,与Gurney flap （GF）对比分析了几何参数对mini-TED后方涡系及翼型气动特性的影响.将mini-TED的几何细节参数定义为弦向长度和有效高度,两者方向正交.在相同迎角下仅改变mini-TED的弦向长度,后缘涡系结构虽发生变化,但翼型气动力几乎没有影响;反之仅改变有效高度则后缘涡系和翼型气动力系数同时发生明显改变,且与同等高度下的GF气动系数相近.结果表明：有效高度是影响翼型气动特性的决定因素.有效高度改变了mini-TED后涡系的发生范围,而相对于整个翼型绕流,后缘涡系的大小是影响翼型流场最重要的因素,而涡系的微观结构和形态的改变影响相对很小.加装mini-TED后上表面激波位置后移、下表面激波强度削弱,从而翼型表面压力分布特性发生了改变.随有效高度增大,mini-TED诱导的涡系发生区域随之增大,引流作用增强,翼型升力系数、阻力系数和低头力矩系数提高,同时相同迎角下翼型的升阻比明显提高.     

翼型尾缘噪声源空间分布与辐射特性关系

详细研究了翼型湍流边界层尾缘宽频噪声源空间分布与辐射特性的关系.采用基于雷诺平均流场的翼型尾缘宽频预测方法研究了NACA0012翼型湍流边界层尾缘宽频噪声在4种不同工况下的噪声源空间分布与辐射特性.首先计算了NACA0012翼型湍流边界层尾缘噪声源在不同频率下的空间分布.计算结果发现:边界层中湍流是翼型湍流边界层尾缘噪声声源.随着频率的增加,噪声源强度和噪声源空间尺寸都是先增加后减小,噪声源位置不断靠近翼型尾缘.同时也计算了边界层内不同位置处的噪声源对远场噪声的辐射特性,结果表明:边界层内层区域,其噪声频谱能量集中在高频;边界层外部区域,其噪声能量集中在中低频;攻角增大或者来流速度减小,噪声能量向低频转移.      

Mass and performance optimization of an airplane wing leading edge structure against bird strike using Taguchi-based grey relational analysis

Collisions between birds and aircraft are one of the most dangerous threats to flight safety. In this study, smoothed particles hydrodynamics (SPH) method is used for simulating the bird strike to an airplane wing leading edge structure. In order to verify the model, first, experiment of bird strike to a flat aluminum plate is simulated, and then bird impact on an airplane wing lead-ing edge structure is investigated. After that, considering dimensions of wing internal structural components like ribs, skin and spar as design variables, we try to minimize structural mass and wing skin deformation simultaneously. To do this, bird strike simulations to 18 different wing structures are made based on Taguchi’s L18 factorial design of experiment. Then grey relational analysis is used to minimize structural mass and wing skin deformation due to the bird strike. The analysis of variance (ANOVA) is also applied and it is concluded that the most significant parameter for the performance of wing structure against impact is the skin thickness. Finally, a validation simu-lation is conducted under the optimal condition to show the improvement of performance of the wing structure.     

复合材料层合锥壳非线性稳定性的有限元分析

本文根据稳定性分析的前屈曲完全理论和修正型的Ｈａｈｎ－Ｔｓａｉ非线性本构关系，采用有限元法分析了复合材料层合回转壳的非线性稳定性，讨论了屈曲产壳体法向与面内支承条件和复合材料的横向和剪切非线性性能对壳体结构总体稳定性的影响，为工程结构设计者们提供了一些有益的参考意见。     

波音737NG飞机后缘襟翼备用方式收起故障的分析

介绍了一起隐蔽的后缘襟翼控制故障，只有在执行指示器更换后的差针指示测试步骤中才表现出襟翼无法收起，通过对电控和液控系统的综合分析，最终查明了原因。     

人造硬壳层扩散作用的研究

主要研究人造硬壳层的扩散作用，运用有限元模拟的方法，在规范规定的基础上确定出了应力扩散角，且得出加肋梁后应力扩散角基本不变的结论。讨论了加肋梁后固化双层地基的硬壳层等效厚度，为工程应用提供参考。     

钛合金蜂窝三层结构的扩散焊接研究

介绍了俄罗斯钛合金蜂窝三层结构扩散焊接的研究成果.详细介绍了铝合金、焊接规范选择、接头应力变形状态的分析、模拟计算等,有助于国内钛合金的焊接研究.     

Lunar geophysical parameters inversion based on gravity/topography admittance and particle swarm optimization

This paper presents a FORTRAN computer program. The program as code will be used for lunar parameter inversions based on gravity/topography admittance. This will be done by assuming that the lunar lithosphere is modeled as a thin elastic spherical shell. The parameters discussed here include; load ratio, crustal thickness, subsurface load depth, crustal density and elastic lithosphere thickness. The admittance of the best-fitting model can be found through automatically adjusting misfits between one theoretical admittance and an observed one. The results in this paper indicate that this research’s theoretical model is reasonable for exploring the best-fitting parameters. In addition, this code is not only able to automatically and simultaneously calculate the global optimum solution of the parameters studied, but also performs well in computational speed. The code can be easily modified to include more parameter inversions; such as the inversion for subsurface density anomaly and the case of considering infilling material in some lunar mare basins.     

脉冲信号快沿计测中的问题

对周期性脉冲信号的频谱进行了简要分析。论述了脉冲信号快沿计测中的问题，讨论了用通用示波器计测脉冲信号时，被测信号的最高频率fM、前沿tr与示波器频带宽度人的关系图和计算公式，讨论了正确选用示波器探头及输入耦合方式．提出了脉冲信号快沿计测中应注意的几个问题。     

空心长轴深孔加工工艺研究

以某发动机空心长轴零件深孔加工为研究对象,设计了长径比为15,长度超过1米的整体硬质合金刀杆,在某加工项目试验中,应用这种超长整体硬质合金刀杆,在细长比大于10的空心长轴的深孔镗削加工中,改变了传统的深孔加工工艺,满足了空心长轴深孔加工中严格的壁厚差要求,取得了明显的效果.