水陆两栖飞机的关键技术和产业应用前景

水陆两栖飞机历经百年的发展,已成为飞机大家族中的稀有机型,但其在现代航空工业中的存在价值和意义却不容忽视,其独特的水陆起降特性更使其依然具有在民用和军事多个领域中应用的优势。除了陆基飞机常规的设计制造技术外,水陆两栖飞机特有的关键技术则是其优良水面起降特性的技术保障,也是航空技术发展的一个重要方面。本文从传统布局和现代创新布局两个方面阐释了水陆两栖飞机的设计特点和技术特征以及发展转变,从水陆两栖飞机水动力特性和气动特性等方面分析了影响其发展的关键技术,并探讨了水陆两栖飞机的产业应用领域前景以及技术发展方向。     

模化设计对离心压气机气动噪声的影响

采用数值计算方法研究了模化设计对压气机气动噪声的影响,三维流场计算结果表明模化设计压气机与原始机型满足相似准则,整级性能参数误差在2%以内;流场结构的分析进一步证实了模化机型与原始机型流场相似。基于非定常雷诺平均方法和声学边界元方法的混合气动声学方法对模化前后的压气机气动噪声进行了数值预测,结果表明:压气机气动噪声主要由离散单音噪声和宽频噪声组成,且离散单音噪声占主导。模化机型总声压级随着模化比减小逐渐减小,相比于原始机型,模化机型离散单音噪声峰值仅略有降低,而宽频噪声大幅提高。压气机气动噪声在进气管口有明显指向性,模化机型声压幅值和指向性较原始机型降低,且变化趋势与模化比成正比。      

侧滑角对鼓包诱导曲面激波/边界层干扰特性的影响

利用仿真方法对侧滑条件下设计马赫数为2的三维壁面鼓包诱导流场进行了研究。结果表明:随着侧滑角的增大,迎风面的展向压力梯度增大,鼓包表面高压中心向迎风面偏移使得迎风面前缘旋涡强度增强,迎风侧出口总压恢复损失,最终导致鼓包下游流场畸变增加。同时鼓包表面流动拓扑结构表明,随着侧滑角的增加,迎风面分离区的准锥形相似特性增强,而背风面由准锥形相似逐渐发展为准柱形相似。      

一种混合励磁同步发电机的气隙磁密分析及其电压谐波抑制

为改善混合励磁同步发电机的气隙磁密分布,采用三段式气隙长度对转子进行了优化,对比了优化前后的气隙磁密。为抑制电压谐波,在完成转子结构优化的基础上,进一步采用短距、分布电枢绕组以及定子斜槽等措施。最后对样机电压波形进行了实测和质量分析,结果表明:采用三段式气隙长度与定子斜槽相结合,可将电压波形的总谐波失真(THD)抑制在5%的范围内。此外,探讨了偏心距法在切向/径向混合励磁电机中应用的可行性,并对比了分别采用偏心距法和三段式气隙长度法时的气隙磁密。     

基于模型预测的多电机弱磁同步控制策略研究

从工业场合下多电机系统高速运行的实际需求出发,分析了传统多电机控制系统和传统弱磁控制系统的优缺点,针对多电机高速运行时的弱磁特性进行了研究。模型预测控制(MPC)是一种基于被控对象模型的新型控制算法,具有较强的鲁棒性和较好的控制性能。交叉耦合控制是一种在并行控制基础上对每个电机进行相应补偿的控制系统。将MPC应用到多电机控制系统中并对其进行改进使其具有弱磁控制能力;对传统的交叉耦合控制策略进行改进。将二者结合提出了一种基于模型预测的多电机弱磁同步控制策略,并以双电机系统为例。最后,进行了仿真验证,仿真试验结果表明,基于模型预测的多电机弱磁同步控制策略,可获得比传统双电机系统更好的跟随性能和同步性能。     

Experimental investigation on aero-heating of rudder shaft within laminar/turbulent hypersonic boundary layers

The aero-heating of the rudder shaft region of a hypersonic vehicle is very harsh, as the peak heat flux in this region can be even higher than that at the stagnation point. Therefore, studying the aero-heating of the rudder shaft is of great significance for designing the thermal protection system of the hypersonic vehicle. In the wind tunnel test of the aero-heating effect, we find that with the increase of the angle of attack of the lifting body model, the increasement of the heat flux of the rudder shaft is larger under laminar flow conditions than that under turbulent flow conditions. To understand this, we design a wind tunnel experiment to study the effect of laminar/turbulent hypersonic boundary layers on the heat flux of the rudder shaft under the same wind tunnel freestream conditions. The experiment is carried out in the ?2 m shock tunnel(FD-14 A) affiliated to the China Aerodynamics Research and Development Center(CARDC). The laminar boundary layer on the model is triggered to a turbulent one by using vortex generators, which are 2 mm-high diamonds. The aero-heating of the rudder shaft(with the rudder) and the protuberance(without the rudder) are studied in both hypersonic laminar and turbulent boundary layers under the same freestream condition. The nominal Mach numbers are 10 and 12, and the unit Reynolds numbers are2.4 × 10~6 m~(-1) and 2.1 × 10~6 m-1. The angle of attack of the model is 20°, and the deflection angle of the rudder and the protuberance is 10°. The heat flux on the model surface is measured by thin film heat flux sensors, and the heat flux distribution along the center line of the lifting body model suggests that forced transition is achieved in the upstream of the rudder. The test results of the rudder shaft and the protuberance show that the heat flux of the rudder shaft is lower in the turbulent flow than that in the laminar flow, but the heat flux of the protuberance is the other way around,i.e., lower in the laminar flow than in the turbulent flow. The wind tunnel test results is also validated by numerical simulations. Our analysis suggests that this phenomenon is due to the difference of boundary layer velocities caused by different thickness of boundary layer between laminar and turbulent flows, as well as the restricted flow within the rudder gap. When the turbulent boundary layer is more than three times thicker than that of the laminar boundary layer, the heat flux of the rudder shaft under the laminar flow condition is higher than that under the turbulent flow condition. Discovery of this phenomenon has great importance for guiding the design of the thermal protection system for the rudder shaft of hypersonic vehicles.     

Effect of drag reducing riblet surface on coherent structure in turbulent boundary layer

The characteristics of turbulent boundary layer over streamwise aligned drag reducing riblet surface under zero-pressure gradient are investigated using particle image velocimetry. The formation and distribution of large-scale coherent structures and their effect on momentum partition are analyzed using two-point correlation and probability density function. Compared with smooth surface, the streamwise riblets reduce the friction velocity and Reynolds stress in the turbulent boundary layer, indicating the drag reduction effect. Strong correlation has been found between the occurrence of hairpin vortices and the momentum distribution. The number and streamwise length scale of hairpin vortices decrease over streamwise riblet surface. The correlation between number of uniform momentum zones and Reynolds number remains the same as smooth surface.     

局部/组合抽吸对压气机叶栅分离流动控制的机理研究

为了研究不同抽吸形式对压气机内部分离流动的控制效果和机理,基于数值模拟方法,对内部同时存在角区分离和附面层分离的直列叶栅进行抽吸计算,共设置8套不同的方案进行了详细的探究。结果表明:对于控制分离的效果和机理,不同抽吸形式之间存在着一定差异;在分离发展的不同阶段,实施抽吸对其控制效果也有所不同。近端壁吸力面抽吸方案SS3同时减小了角区分离和近端壁处的尾缘附面层分离,尾部近吸力面沿展向静压分布为正"C"型,使角区内的低能流体向叶中流动,角区流动得到改善,但导致叶展中部流场的恶化;端壁抽吸和全叶高组合抽吸则使尾部近吸力面静压沿展向分布更均匀,低能流体的迁移现象减弱。基于以上结果可得:组合抽吸可以更有效地控制叶栅内部流动分离,降低损失,提高叶栅流通能力。     

两种翼型螺旋桨ARA-D和S1223的等离子体增效实验研究

文章首先基于雷诺相似理论,在地面螺旋桨实验平台上开展ARA-D翼型螺旋桨微秒脉冲等离子体增效三维实验,结果表明,等离子体对螺旋桨拉力增效效果随着脉冲频率增加而减弱,而螺旋桨转矩受等离子体影响随拉力增效效果增加而减弱,拉力、效率最大增幅分别达到10.79%、11.56%。而后基于雷诺相似理论及叶素理论,在低湍流度风洞开展S1223翼型螺旋桨叶素微秒脉冲等离子体增效二维实验,结果表明等离子体激励提高了翼型各叶素拉力,其中根部与尖部叶素表现尤为明显。二维实验结果可为三维实验激励器展向排布方案提供理论依据。2种实验结果均表明,等离子体射流可以有效抑制翼型表面流动分离。     

基于聚类状态主控边界点的单调多态关联系统可靠性分析

鉴于组成系统单元的多状态单调关联性特征,将多元离散函数理论引入描述系统状态结构函数,发展了控制状态等价类主导状态向量的状态等价类主控边界点的逻辑方法,推导了多态单调关联系统的状态结构函数、可靠性和期望状态表达式;面向顾客的需求偏好,将负效用函数嵌入系统平均性能效用模型;鉴于元件状态引起的计算复杂性,提出了集合运算的德摩根律法和新型的框图式算法,简化了系统可靠度的表达式。结合某型航空发动机的简化演算,验证了主导等价类向量方法和框图算法的合理性与有效性,为工程系统的可靠性设计和可靠性管理提供理论依据。