水陆两栖飞机方向舵附面层控制研究

水陆两栖飞机采用增升手段降低起降速度后,需要提高方向舵的操纵能力。将吹气式附面层控制方法应用到水陆两栖飞机的垂尾上,建立其二维模型并进行数值模拟,设计垂尾安定面与方向舵之间的缝道挡板,防止迎风一侧的高压气流冲击背风面、阻碍吹气气流附着;研究垂尾安定面后缘和前缘吹气共同作用的组合吹气方案,防止方向舵较早失速。结果表明:垂尾采用吹气式附面层控制之后,结合缝道挡板和组合吹气,方向舵操纵能力可提高1倍左右。     

短螺旋型燃烧室旋流结构及气动边界发展规律数值模拟研究

短螺旋型燃烧室的头部轴线沿发动机周向与发动机轴线偏转一定角度,可以在保证燃烧效率不变的条件下有效缩短燃烧室轴向长度。短螺旋型燃烧室流场的最大特点是旋流流动单侧受限。为了研究头部安装角α变化对燃烧室旋流流动特性的影响,基于数值方法对短螺旋型燃烧室进行了计算分析。结果表明:随着α变化,旋流器下游旋涡依次出现对称环状、马蹄状、环状结构;随着α增加,气动边界逐渐出现并抑制旋流的周向扩张,导致流场出现不同的旋涡结构;不同α下的切向角动量随轴向距离增加而衰减,但α为35°和45°时,气动边界在非受限侧出现并对旋流产生约束,角动量衰减变慢;当α为0°,15°,35°,45°时,燃油液滴依次集中分布在旋流器下游两旋涡边缘、侧壁面和头部端壁、非受限旋涡边缘。本文研究了不同α下的旋涡结构及气动边界沿轴向的演化过程,为短螺旋型燃烧室进一步的设计与优化提供基础。     

新电位移边界条件下的压电介质断裂问题

应用边界元法,并结合一种特殊的复变函数基本解,研究了压电介质的断裂问题。由于该基本解完全遵循本构方程没有对电位移边界作假设,所以结论同非穿透性裂纹假设的结果有较大差异。通过计算表明,外加力载荷不但会引起裂纹尖端应力奇异性,也会引起电场奇异性,同样,外加电压也会引起裂纹尖端应力奇异性。     

干涉配合构件的应力腐蚀开裂特性

采用恒载荷拉伸实验技术,研究了镀锌３０ＧｒＭｎＳｉＡ锡螺栓干涉配合连接ＬＹ１２－ＣＺ铝合金构件在３．５％ＮａＣａｌ＋０．５％Ｈ２Ｏ２溶液中的应力腐蚀开裂特性。结果表明,随干涉量的增加,应力腐蚀敏感性有所下降,基材与紧固件的电偶效应对应力腐蚀繁感性有重大影响。     

Effects of yaw-roll coupling ratio on lateral-directional aerodynamic characteristics

Experimental investigation of large amplitude yaw-roll coupled oscillations was conducted in a low-speed wind tunnel using an aircraft configuration model. A special test rig was designed and constructed to provide different coupled motions from low to high angles of attack.A parameter ‘‘coupling ratio" was introduced to indicate the extent of yaw-roll coupling. At each pitch angle, seven coupling ratios were designed to study the yaw-roll coupling effects on the lateraldirectional aerodynamic characteristics systematically. At high angles of attack, the damping characteristics of yawing and rolling moments drastically varied with coupling ratios. In the coupled motions with the rotation taking place about the wind axis, the lateral-directional aerodynamic moments exhibited unsteady characteristics and were different from the ‘‘quasi-steady" results of the rotary balance tests. The calculated results of the traditional aerodynamic derivative method were also compared with the experimental data. At low and very high angles of attack, the aerodynamic derivative method was applicative. However, within a wide range of angles of attack, the calculated results of aerodynamic derivative method were inconsistent with the experimental data, due to the drastic changes of damping characteristics of lateral-directional aerodynamic moments with yaw-roll coupling ratios.     

Coupled Stress-Electricity Model for Electromagnetic Emission Induced by Concrete Fracture

Electromagnetic emission induced during concrete fracturing is of great significance to health monitoring of concrete structures.A coupled stress-electricity model is established by analyzing the interaction between stress and electricity during concrete fracturing.And based on this model,the electromagnetic radiation parameters are calculated.The theoretical calculation is well coincident with experimental results.This work provides theoretical support for concrete testing system.     

采用平面叶栅模拟压气机动叶叶尖间隙流

 通过对动叶叶尖进口端壁附面层的性状分析,指出采用平面叶栅模拟动叶叶尖间隙流端壁面静止(工况 1 )和仅有端壁面运动 (工况 2 )进口端壁附面层与真实情况的差异。根据转子静止静子转动这一相对运动思想设计出动叶叶尖间隙流实验模型 (工况 3)。对上述 3种工况叶片表面静压分布和叶尖间隙流进行了实验测量。实验表明:工况 3比 2,1叶尖间隙泄漏涡生成得早且间隙泄漏流量较大;采用无粘叶尖间隙流计算模型,在叶片后面部分计算结果与实测值吻合较好,而在叶片前缘部分由于流向压力梯度较大使得计算值大于实测值。     

含孔边裂纹板的弯曲断裂计算

 采用复变函数理论和边界配置方法 ,对含孔边裂纹板的弯曲断裂进行了分析计算。首先假设挠度的复变函数式 ,进而可以求板的内力。它们能满足一系列的基本方程和支配条件 ,仅板的边界条件需要考虑 ,并且可用边界配置法和最小二乘法近似满足。对孔双边裂纹问题进行了应力强度因子计算。数值算例表明 ,本文方法精度较高 ,计算量小 ,是一种有效的半解析、半数值计算方法。     

气膜冷却叶片上扩散型冷却孔对紊流流场的影响

带有护散型冷却孔的气膜冷却叶版是新开发的结构，用于具有很市初始温度（1700℃）的氢气燃气轮机，名古屋工业大学流体机械实验室在日本首次对该结构的流场进行了研究。用垂直型和X型的热线测量了流场，获得了主流方向平均速度，紊流强度和雷诺剪应力，在沿下游方向和展向方向的平面里分别整理了实验数据，证实了扩散冷却孔对改善燃气轮机膜冷却紊流流场的效果。     

平板湍流摩阻系数的显式表达式

 湍流摩阻系数的计算是工程技术中经常遇到的问题。计算时所依据的公式多为半经验半理论的结果,如Karman公式,Van Driest公式和Prandtl公式等。这些公式是以隐函数给出的,给计算带来不便。但是不难发现,这类公式经过适当的变换,可以化为统一形式的超越代数方程,这种方程没有有限形式的解析解,本文给出了一种近似解析解。根据这种方法除了导出上述公式的显式表达式外,还对White公式作了修正。当然解超越代数方程最根本的方法是迭代法,本文对此也作了简单讨论。