飞机数字化装配系统中机身交点孔加工方法研究

针对传统交点孔加工方法加工精度低且存在回弹变形的问题,设计了一种满足飞机大部件数字化装配要求的机身交点孔精加工方法,根据交点孔的加工特性完成了机身定位与固持、数控加工中心定位以及加工工艺的总体设计,确定了交点孔加工程序原点的计算方法和编程原则,最后通过交点孔试切加工试验验证了加工方法的可行性。     

Application of small-size antennas for estimation of angles of arrival of HF signals scattered by ionospheric irregularities

A modification of the Doppler Interferometry Technique is suggested to enable estimating angles of arrival of comparatively broadband HF signals scattered by random irregularities of the ionospheric plasma with the use of small-size weakly directional antennas. The technique is based on the measurements of cross-spectra phases of the probe radiation recorded at least in three spatially separated points. The developed algorithm has been used to investigate the angular and frequency-time characteristics of HF signals propagating at frequencies above the maximum usable one (MUF) for the direct radio path Moscow-Kharkiv. The received signal spectra show presence of three families of spatial components attributed, respectively, to scattering by plasma irregularities near the middle point of the radio path, ground backscatter signals and scattering of the sounding signals by the intense plasma turbulence associated with auroral activations. It has been shown that the regions responsible for the formation of the third family components are located well inside the auroral oval. The drift velocity and direction of the auroral ionosphere plasma have been determined. The obtained estimates are consistent with the classical conception of the ionospheric plasma convection at high latitudes and do not contradict the results of investigations of the auroral ionosphere dynamics using the SuperDARN network.     

热力学排气系统中节流效应及其冷量利用分析

为更好地理解热力学排气系统(TVS)的运行机理，优化其运行参数，针对节流装置，建立了热力学模型，讨论了节流过程中状态参数的变化规律，对比了单相气体、单相液体节流的性能特性，进一步揭示了焦汤节流效应的原理，分析了不同节流背压下节流前低温工质(液氢和液氧)压力和温度对节流性能的影响，并结合TVS实际应用，阐述了节流最大制冷量的利用效果，提出了优化的TVS工作区间。研究表明：在节流过程不发生相变情况下单相气体节流制冷效应要比单相液体节流制冷效应更加显著；而在节流过程发生相变情况下液体节流至两相后，由于空化吸热导致流体温度降低，对于液氢，0.5MPa的压降可产生接近3 K的温降。对于液体节流，节流前压力对节流过程影响可忽略，〖JP2〗而节流前温度和节流背压对节流过程起主导作用；对于液氢在在轨运行工况下，考虑到节流制冷量的充分利用，同时保证换热过程体积含气率不高于90%，推荐TVS系统中节流背压范围为75～143 kPa。     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.     

Alfvén gravity waves in viscous solar plasma: Effect of the background flow

We study the Propagation and damping properties of Alfvén gravity waves in the presence of the vertical magnetic field in the viscous solar plasma under influence of the background flow by deriving a fourth order dispersion relation in terms of the Doppler shifted frequency. We derive the dispersion relation under WKB and Boussinesq approximation. We study the damping of Alfvén gravity waves for the wave frequencies less than and greater than the Brunt-Väisälä frequency. We find that the Brunt-Väisälä frequency divides the frequency ranges where the weakly or strongly damped oscillations occur. The background flow exhibits a strong effect on weakly damped oscillations and a weak effect on the strongly damped oscillations. We also notice that the damping of both the strong and weakly damped oscillations depend on the Brunt-Väisälä frequency and wave number. The effect of the background flow is also being governed by the Brunt-Väisälä frequency and wave number. We also study the properties of gravity wave mode after filtering the Alfvén wave mode by minimizing the magnetic field and noticed that the background flow shows a very strong effect on the gravity wave mode.     

先进航发旋转雾化喷嘴制造技术

喷射油道是一种高精度旋转雾化喷嘴,其非连续窄深端槽、窄深槽、3/4圆弧窄端槽为行业内少见结构.通过分析喷射油道特有结构的加工工艺,摸索油孔尺寸与燃油流量的匹配关系,解决了非连续深窄端槽、窄深槽、细微孔电火花成形加工、3/4圆弧窄端槽高效数控加工、高精度喷嘴孔流量调试等关键技术瓶颈,具有一定的指导意义和广阔的应用前景.     

阵风载荷减缓系统故障分析

阵风引起的额外载荷会引起飞机结构疲劳,降低结构使用寿命。采用非定常气动力有理函数拟合方法建立时域状态空间下的动力学系统,设计了阵风载荷减缓系统。研究了阵风载荷减缓系统3种典型故障模式(副翼偏转饱和、舵机卡死、副翼偏转延时)的力学建模方法,并对机翼在阵风减缓系统故障模式下的阵风响应进行分析。仿真结果表明,3种故障模式均不利于阵风载荷减缓系统对阵风载荷的减缓,对于一些特定情况,故障模式下的阵风载荷减缓系统不仅不能减缓阵风载荷,还会带来由副翼偏转不当引起的额外负载。     

简论高校实验课程的改革

实验教学是高等院校教学过程的一个重要环节,应建立新型的实验室管理模式,从开放实验室和改革教学方法两个方面出发,阐述了实验课程改革的必要性。     

Aerodynamics of smart flap under ground effect

Aerodynamic characteristics of two-dimensional smart flap under the ground effect have been assessed by a numerical simulation. In this process, a pressure-based implicit procedure to solve Navier–Stokes equations on a nonorthogonal mesh with collocated finite volume formulation is used. The boundedness criteria for this procedure are determined from the Normalized Variable Diagram (NVD) scheme. The procedure incorporates the k–ε eddy–viscosity turbulence model. Cantilever beam with uniformly varying load with roller support at the free end is considered for the configuration of the smart flap. The method is first validated against experimental data. Then, the algorithm is applied for turbulent aerodynamic flows around airfoil with smart and conventional flaps for different attack angle, flap angle and ground clearance where the results of two flaps are compared. The comparisons show that the quality of the solution is considerable.     

激光器性能综合测试设备研制

介绍了激光器的主要性能指标,根据实际需要进行了激光性能测试设备的研究,提出了一种周全的激光性能测试设备研制方案,对该设备的结构设计、光路设计、以及测试方法作了详尽论述。设备中利用两对相互垂直的P分光镜和S分光镜以补偿偏振光在45°面上透反射率不同而造成的测量误差,进一步保证了激光能量测试的准确性。误差分析结果表明该设备满足实际应用中对激光器性能的测试要求。