交错肋结构形式对换热和流阻特性的影响试验研究

通过试验,研究了不同结构的交错肋对换热及流阻特性的影响。试验结果表明:努塞尔数和流阻系数,随着肋宽的增大而都增大,随着肋间距的增大而都减小,随着肋倾角的增大而都增大。综合换热效果为1.3~2.5。     

A Comparative Study of the Influence of the Active Young Sun on the Early Atmospheres of Earth, Venus, and Mars

Because the solar radiation and particle environment plays a major role in all atmospheric processes such as ionization, dissociation, heating of the upper atmospheres, and thermal and non-thermal atmospheric loss processes, the long-time evolution of planetary atmospheres and their water inventories can only be understood within the context of the evolving Sun. We compare the effect of solar induced X-ray and EUV (XUV) heating on the upper atmospheres of Earth, Venus and Mars since the time when the Sun arrived at the Zero-Age-Main-Sequence (ZAMS) about 4.6 Gyr ago. We apply a diffusive-gravitational equilibrium and thermal balance model for studying heating of the early thermospheres by photodissociation and ionization processes, due to exothermic chemical reactions and cooling by IR-radiating molecules like CO₂, NO, OH, etc. Our model simulations result in extended thermospheres for early Earth, Venus and Mars. The exospheric temperatures obtained for all the three planets during this time period lead to diffusion-limited hydrodynamic escape of atomic hydrogen and high Jeans’ escape rates for heavier species like H₂, He, C, N, O, etc. The duration of this blow-off phase for atomic hydrogen depends essentially on the mixing ratios of CO₂, N₂ and H₂O in the atmospheres and could last from ∼100 to several hundred million years. Furthermore, we study the efficiency of various non-thermal atmospheric loss processes on Venus and Mars and investigate the possible protecting effect of the early martian magnetosphere against solar wind induced ion pick up erosion. We find that the early martian magnetic field could decrease the ion-related non-thermal escape rates by a great amount. It is possible that non-magnetized early Mars could have lost its whole atmosphere due to the combined effect of its extended upper atmosphere and a dense solar wind plasma flow of the young Sun during about 200 Myr after the Sun arrived at the ZAMS. Depending on the solar wind parameters, our model simulations for early Venus show that ion pick up by strong solar wind from a non-magnetized planet could erode up to an equivalent amount of ∼250 bar of O⁺ ions during the first several hundred million years. This accumulated loss corresponds to an equivalent mass of ∼1 terrestrial ocean (TO (1 TO ∼1.39×10²⁴ g or expressed as partial pressure, about 265 bar, which corresponds to ∼2900 m average depth)). Finally, we discuss and compare our findings with the results of preceding studies.     

含裂纹金属薄板的断裂韧度与剩余强度研究

为了探究影响含裂纹铝合金薄板材料断裂韧度、剩余强度的几何因素以及韧性材料的断裂机理,对典型航空铝合金2524-T3薄板,采用不同宽度、不同初始裂纹长度的中心裂纹板试样进行试验,测定材料的K-R阻力曲线,确定平面应力断裂韧度Kc和表观断裂韧度Kapp.试验结果表明:对于薄板结构,K-R阻力曲线与板宽相关;试件宽度、初始裂纹长度对断裂韧度和表观断裂韧度的确定都有影响,且板宽度的影响较大.基于上述结论,推荐两种可同时反映韧性材料断裂中的净截面屈服效应和韧性撕裂过程的剩余强度预测方法.     

Ω长桁和T长桁的工艺对比分析研究

在飞机复合材料蒙皮类构件的设计制造过程中,早期设计阶段,对不同长桁结构进行工艺对比分析研究,有助于提高加筋壁板的结构性能、便于工艺优选、节约制造成本,实现面向制造的低成本最优化设计。针对飞机复合材料蒙皮与Ω长桁、T长桁共固化的典型结构,阐述二者的制造流程及工艺特点;从制造工艺、工时、花费、产品重量和抗冲击性能等方面,对比Ω长桁和T长桁的优缺点;提出在飞机设计制造的并行工程中进行不同结构工艺分析的方法。结果表明:Ω长桁相对T长桁,具有重量轻、抗冲击性能好等优点,但其制造工艺更为复杂,报废率高,制造成本较高。     

2A12-T4铝合金长期大气腐蚀损伤规律

在海南省万宁地区开展了2A12-T4铝合金暴露7年、12年和20年的大气腐蚀试验,根据腐蚀特征将腐蚀区域划分为单侧腐蚀区和双侧腐蚀区,以结构最小剩余厚度值作为腐蚀特征量,进行了不同年限试验件中不同腐蚀区域最小剩余厚度的测量和统计分析,确定了满足99.9%可靠度与95%置信度的最小剩余厚度值以及95%置信度下的最小剩余厚度置信区间,并开展了腐蚀损伤形貌的金相分析。研究结果表明:2A12-T4铝合金大气腐蚀特征量服从正态分布;在大气腐蚀7~20年间2A12-T4铝合金板件的最小剩余厚度值是线性减小的;2A12-T4铝合金大气腐蚀7年后处于点蚀、晶间腐蚀、剥蚀的过渡期,12年后发生全面剥蚀,20年后剥蚀已相当严重且伴随着点蚀;双侧腐蚀区与单侧腐蚀区相比腐蚀深度更大且剥蚀层剥落严重。     

接触特性对非连续性转子热致振动的影响

针对燃气轮机转子的非连续性结构间存在的接触特性,根据微凸体理论引入接触刚度和接触热阻的等效模型,建立了某型燃气轮机非连续性转子的动力学模型,分析了接触参数对转子稳、瞬态动力学特性的影响,研究了螺栓松动引起的转子热变形及其对转子快速启动过程中振动特性的影响.结果表明:预紧力、接触面的表面粗糙度和螺栓个数对转子临界转速有一定的影响,螺栓松动导致转子在启动过程中瞬态热变形最大达到7μm,过1阶临界转速时引起的转子最大响应幅值增大约30μm.在非连续性转子系统的热致振动特性分析当中,不应忽视接触参数、接触刚度和接触热阻的影响.      

一种弹性低密度耐高温隔热涂层

针对固体火箭发动机实际使用的热环境要求,研制了一种弹性低密度耐高温隔热涂层,通过石英 灯辐射和电弧风洞试验对其进行了防热性能考核。该涂层密度为0. 62 g/ cm3,伸长率为25%,热导率为0． 18 W/ (m·K);在401℃时DSC 失重率仅为6. 6%;验证考核表明,采用1. 0 mm 涂层时,壳体与涂层界面温度最高 为77. 3℃,壳体背温度最高为44. 5℃。     

Effect of sodium tartrate concentrations on morphology and characteristics of anodic oxide film on titanium alloy Ti–10V–2Fe–3Al

The effect of sodium tartrate concentrations on morphology and characteristics of ano-dic oxide film on titanium alloy was investigated. The alloy substrates were anodized in different concentration solutions of sodium tartrate with the addition of PTFE emulsion and their morphol-ogy and characteristics were analyzed. The anodic oxide film presented a uniform petaloid drums and micro-cracks morphology. Additionally, micro-cracks dramatically swelled with the increase of the tartrate concentrations. The thickness of the anodic oxide film increased with the concentra-tions until the concentration reached 15 g/L. The results of Raman analysis illustrate that all sam-ples have similarity in the crystal structure, consisting of mainly amorphous TiO2, some anatase TiO2 and a small amount of rutile TiO2. And the ratios of anatase TiO2 and rutile TiO2 increase with the concentrations until it reaches 15 g/L. Furthermore, the intensity of the peaks increases with enhanced concentrations until the concentration reaches 15 g/L. The corrosion resistance of the anodic oxide film is increased by the sodium tartrate with higher concentrations before 15 g/L. The coefficient of friction of the anodic oxide film reduces with the concentrations until the concentration reaches 15 g/L, then the coefficient of friction of the anodic oxide film increases with the concentrations.     

纳秒脉冲表面介质阻挡放电激励改善飞翼力矩特性的实验研究

针对飞翼布局力矩控制问题,采用纳秒脉冲表面介质阻挡放电（NS-DBD）激励,在来流风速30 m/s时,开展飞翼等离子体流动控制风洞试验,研究了不同激励参数和位置对飞翼升阻特性和力矩特性的影响。结果表明,NS-DBD激励能够有效改善飞翼大迎角气动特性。激励频率对飞翼升阻特性影响较大,激励频率为0.2 kHz时,增升效果最好,最大升力系数提高14.5%,失速迎角推迟5°。随着激励频率的增加,增升效果逐渐变差,减阻效果变好。单侧施加激励时,能够实现大迎角下飞翼模型的力矩控制,随着激励频率的增加,滚转力矩的控制效果减小,激励频率为0.2kHz时,平均滚转力矩系数变化为ΔMX=0.005691;偏航力矩的控制效果增大,激励频率为1kHz时,平均偏航力矩系数变化为ΔMY=-0.001571;俯仰力矩的控制效果减小,激励频率为0.2kHz时,平均俯仰力矩系数变化为ΔMZ=-0.002576。在中翼段和内翼段施加激励,破坏了飞翼的俯仰力矩特性,在外翼段和机翼右侧施加激励,能够显著改善飞翼的俯仰力矩特性。流场测量结果表明：等离子体激励对飞翼气动力矩的控制,主要是通过控制流动分离和控制横向流动来实现的。NS-DBD激励为改善飞翼布局稳定性和操纵性提供一种潜在的技术手段。     

铝合金壳体阳极化膜颜色异常分析

铝合金壳体在阳极化处理后表面阳极化膜存在颜色异常(发黑)现象。本文通过对壳体阳极化膜表面及基体形貌观察、金相分析和成分分析对发黑的原因进行了分析。结果表明壳体阳极化膜发黑的原因是由于该区域存在成分偏析(合金含量高),导致该区域的晶粒尺度比正常区域小、耐蚀性比正常区域差,膜层微观结构与正常区域存在差异,膜层内部化合物较多,致使该区域膜层呈现黑色。