改进升力线理论和风洞试验结合的气动弹性修正方法

本文介绍了一种基于亚音速稳态定常流改进升力线理论与风洞试验相结合的大展弦比亚音速飞机的弹性翼面气动力分布载荷修正方法,设计目的是为了考虑具有大展弦比、弹性翼面结构的飞机翼面结构弹性变形对气动载荷分布的影响。     

An adaptive fast fixed-time guidance law with an impact angle constraint for intercepting maneuvering targets

Sliding mode guidance laws based on a conventional terminal sliding mode guarantees only finite-time convergence, which verifies that the settling time is required to be estimated by selecting appropriate initial launched conditions. However, rapid convergence to a desired impact angle within a uniform bounded finite time is important in most practical guidance applications. A uniformly finite-time/fixed-time convergent guidance law means that the convergence (settling) time is predefined independently on initial conditions, that is, a closed-loop convergence time can be estimated a priori by guidance parameters. In this paper, a novel adaptive fast fixed-time sliding mode guidance law to intercept maneuver targets at a desired impact angle from any initial heading angle, with no problems of singularity and chattering, is designed. The proposed guidance law achieves system stabilization within bounded settling time independent on initial conditions and achieves more rapid convergence than those of fixed-time stable control methods by accelerating the convergence rate when the system is close to the origin. The achieved acceleration-magnitude constraints are rigorously enforced, and the chattering-free property is guaranteed by adaptive switching gains. Extensive numerical simulations are presented to validate the efficiency and superiority of the proposed guidance law for different initial engagement geometries and impact angles.     

非均质壁面对液滴俘获能力的数值模拟研究

为研究不同非均质壁面对液滴的俘获能力,采用界面追踪法（FTM）结合广义滑移边界建立了接触角模型,对液滴在非均匀润湿的非均质壁面上的运动过程进行了数值模拟研究。液滴在倾斜壁面上受到重力作用由均匀润湿部分下滑至非均匀润湿部分,通过改变Bo数、Oh数、非均匀润湿程度研究了液滴在非均匀润湿区域的运动规律。研究表明:Bo数越大,液滴运动受壁面阻力影响越小,液滴下滑的速度越快,液滴越难以被俘获;Oh数越大,液滴运动受壁面阻力影响越小,液滴越难以被俘获;非均匀润湿程度越大,非均质壁面对液滴的阻力越大,液滴越易被俘获。      

宽高比及表面粗糙度对矩形微尺度通道流动特性的影响

实验研究了不同宽高比矩形金属微尺度通道的流动特性,并与硅通道对比来探究表面粗糙度的影响。金属微尺度通道宽为0.4mm,通道宽高比分别为0.50、0.67、和1.00,相对表面粗糙度范围为0.1609%~0.2145%。硅通道宽度及高度都为0.4mm,相对表面粗糙度为0.00325%。实验工质为空气,实验的雷诺数范围是250~3000。实验结果表明:在粗糙微尺度通道会发生转捩提前,并且转捩雷诺数随着宽高比增大而减小。在层流区,微尺度矩形通道摩擦因数随着雷诺数增大而减小,在转捩区出现明显增大后再减小。表面粗糙度很小时,未发现转捩提前现象。      

转子叶栅非同步振荡发声特性研究

轴流压气机转子叶片排振荡疲劳失效是常见的气动弹性失稳问题。当转子叶栅处于非同步振荡状态下时,压气机管道内部将伴随着异常噪声的产生,这类噪声的频率既不是分布在叶片通过频率及其谐波上,也不是分布在转子轴频率及其谐波上,同时也不满足简单多普勒效应。为了解释这种异常噪声现象,以三维升力面理论为基础,讨论叶片对其附近流体施加非定常载荷的发声问题,给出了转子叶栅振荡异常发声问题的物理解释,建立了声场频率及模态特性与转子声源特性的直接关系式,并给出了频率特性不同于叶片通过频率且不符合简单多普勒效应的完整解释。在此基础上,通过机理性实验研究证实了该模型的正确性。实验结果表明,理论预测声场的频率和周向模态特性与实验结果完全一致。     

双U型管束模型换热器的流动和传热特性

为了研究双U型管束模型换热器的流动和传热性能,通过低速高温风洞的模型实验和Fluent-CFD数值计算,得到了换热器的管型和安装角对换热器压降和回热效率的影响规律。结果表明:在相同的双U型管管内气流平均流动速度下,椭圆管换热器的管内流动压降高于圆管换热器的,相对增加幅度在50%~60%之间;对于外部流动,换热器安装角度增大所诱导的外部流动压降显著增加,在换热器30°的安装角下,椭圆形管束的低阻流动型面得以充分体现,其外部流动压降较圆形管束换热器可以降低约50%;随着换热器安装角的增加,换热器回热效率具有明显的提高;相对换热器安装角,换热器管型对回热效率的影响较小,集气管的进气-出气方式对双U型管束换热器的回热效率具有较显著的影响。     

考虑气动力非线性的柔性飞机阵风响应分析

针对大展弦比柔性飞机阵风响应问题,考虑在大攻角(AOA)情况下气动力非线性的影响,通过将修正的Theodorsen方法与片条理论相结合,得到非线性的时域非定常气动力;在此基础上,建立阵风干扰下的大展弦比柔性飞机非线性气动弹性模型,完整地发展了一种新颖的可考虑气动力非线性的大展弦比柔性飞机阵风响应分析方法.结合算例模型开展方法验证和数值仿真,对比翼尖和质心(CG)处阵风附加过载在线性和非线性情况下的变化.算例结果表明,考虑大攻角情况下的气动力非线性后,大展弦比飞机的阵风响应较线性情况有明显变化,翼尖处的阵风附加过载最多可减少41.7%,气动力非线性的影响不可忽视.      

Laser-induced oxidation assisted micro milling of high aspect ratio microgroove on WC-Co cemented carbide

Severe tool wear and poor surface quality are the main problems during micro machining of cemented carbide. In this work, an innovative hybrid process of laser-induced oxidation assisted micro milling (LOMM) was proposed to solve the problems. A nanosecond laser was utilized to induce oxidation of the WC-20%Co material, producing loose oxide which was easy to remove. The micro machinability of the material was improved by laser-induced oxidation. The oxidation mechanisms of cemented carbide were studied. A microgroove with a depth of 2.5 mm and aspect ratio of 5 was fabricated successfully. The milling force, surface quality and tool wear mechanisms were investigated. For comparison, a microgroove was also fabricated with conventional micro milling (COMM) using identical milling parameters. Results revealed that in LOMM the milling force and tool wear rate were extremely low during removing the oxide. The machined surface quality and dimensional accuracy achieved by LOMM were superior to those obtained by COMM. The surface roughness S_a of the microgroove bottom reached 88 nm in LOMM, while the cross-sectional geometry of the microgroove was a trapezoid. Perpendicularity of the microgroove sidewall machined by LOMM was better than that by COMM. The tool wear forms in LOMM were coating spalling and slight tool nose breakage. Compared with COMM, the tool life in LOMM was prolonged significantly. It indicates that the proposed hybrid process is an effective and efficient way to fabricate high aspect ratio micro-features with high dimensional accuracy.     

双后掠鸭翼气动特性的数值模拟

首先针对具有中等前缘后掠角梯形鸭翼的缺点提出双后掠鸭翼概念,然后分别对安装梯形鸭翼和双后掠鸭翼的近距耦合鸭式布局的气动性能进行数值模拟研究,分析影响双后掠鸭翼气动性能的流动机理。研究表明：在大迎角时,对于双后掠鸭翼,具有较大前缘后掠角的外翼段可以使鸭翼涡在涡核破裂后仍能形成稳定集中涡并保持较高的强度,增加鸭翼本身的失速迎角,并通过诱导作用改善机翼外翼段流场,进而提高全机大迎角性能,但在小迎角时会破坏鸭翼附着流或前缘气泡涡的发展,造成略微的升力损失。拥有较大失速迎角的双后掠鸭翼在小迎角时具有较大的可用偏度,可以增强布局的抬头控制能力。双后掠鸭翼在满足隐身约束的前提下,超声速阻力较小,具有较好的超声速性能。     

同轴撞击气-气喷嘴数值模拟和实验

为进一步深入研究喷嘴结构参数对气-气掺混燃烧特性的影响,针对氢向氧斜喷带撞击角度的气-气喷嘴开展了实验和数值模拟.实验研究了撞击角度对燃烧效率和燃烧室壁面温度的影响,数值仿真分析了撞击角度对喷注面板和氧喷嘴管壁温的影响.结果表明:随着氢向氧撞击角度的增大,推进剂燃烧效率、燃烧室壁面和氧喷嘴出口管壁面热载降低;氢向氧撞击角度的引入,增大了喷注面板热载.