水上飞机浮筒外形设计的微机系统

本文介绍了一个水上飞机浮简外形设计的微机系统FCDS。浮筒外形是一张须满足流体静、动力等性能要求的复杂的三维曲面。FCDS以性能优良的库模型作为外形曲面生成的基础,使曲面的进一步设计有了一定的流体性能上的保证。系统用非均匀有理B样条来作曲线曲面的拟合和交互设计。不仅继承了普通多项式非均匀B样条重节点、重顶点等设计技巧,而且增加了形状调节的能力,同时可将二次曲线曲面统一在三次有理式中。系统提供了用穗坂卫法直接光顺空间曲线和曲面的功能,可对浮筒外形进行光顺处理,提供直接用于制造的数据。文中还对FCDS这类专业曲面CAD系统的设计构思、结构组成作了探讨。系统设计的通用性构思,使FCDS稍作修改即可用于其他飞机部件的外形设计。     

ΔDsat,a QB50 CubeSat mission to study rarefied-gas drag modelling

A CubeSat mission to study the impact of flow incidence angle, surface material and surface roughness on gas–surface interactions on spacecraft in low Earth orbits has been designed. To accomplish this scientific goal the CubeSat deploys a variable geometry aerofoil capable of exposing different surfaces to the flow at different incident angles. By using the on-board GPS measurements and an orbit determination technique the drag experienced by the CubeSat can be estimated. The CubeSat has been designed to be part of the QB50 mission, and hence it carries a sensor that can take in-situ measurements of the atmosphere. This is then used to estimate the atmospheric density and hence to extract information on the drag coefficient. To minimise any bias present in the measurement chain a differential approach is used. Therefore no absolute drag coefficients are estimated, instead, ratios of drag coefficients are computed. This allows direct comparisons of the drag coefficients of different materials, different surface roughness or different incident angles. Simulations indicate that this CubeSat mission will be able to obtain drag coefficient ratios with an uncertainty level of less than 5%.     

水泥混凝土路面损坏的原因及防治措施

水泥混凝土路面具有强度高、使用寿命长、稳定性好、不易变形等特点,在建设中广泛采用。但在行车荷载和环境因素的作用下会出现不同类型的损坏,本文据此有针对性地采取了防治措施,以避免水泥混凝土路面损坏。     

MESSENGER and the Chemistry of Mercury’s Surface

The instrument suite on the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft is well suited to address several of Mercury’s outstanding geochemical problems. A combination of data from the Gamma-Ray and Neutron Spectrometer (GRNS) and X-Ray Spectrometer (XRS) instruments will yield the surface abundances of both volatile (K) and refractory (Al, Ca, and Th) elements, which will test the three competing hypotheses for the origin of Mercury’s high bulk metal fraction: aerodynamic drag in the early solar nebula, preferential vaporization of silicates, or giant impact. These same elements, with the addition of Mg, Si, and Fe, will put significant constraints on geochemical processes that have formed the crust and produced any later volcanism. The Neutron Spectrometer sensor on the GRNS instrument will yield estimates of the amount of H in surface materials and may ascertain if the permanently shadowed polar craters have a significant excess of H due to water ice. A comparison of the FeO content of olivine and pyroxene determined by the Mercury Atmospheric and Surface Composition Spectrometer (MASCS) instrument with the total Fe determined through both GRNS and XRS will permit an estimate of the amount of Fe present in other forms, including metal and sulfides.     

月球表面及月壤内温度分布特征的数值模拟

文章建立了月表辐射与月壤内二维非稳态导热的耦合传热模型,采用控制容积法数值模拟月壤内的温度分布,主要研究了月表、月壤内温度的分布和变化规律及探测器对局部月表温度的影响。计算结果表明一昼夜期间月壤内存在明显的温差:浅层月壤处的昼夜温差较大且受纬度的影响明显;随着深度的增加,月壤昼夜温差降低并趋于稳定,且受纬度的影响较小。探测器的存在遮挡了月表接受的太阳辐射,导致其阴影区域内月表温度发生突变,新的平衡温度接近探测器底面温度,且受探测器驻留时间的影响较小;当探测器移开,月表温度又迅速恢复到原有的变化规律。     

考虑弹性变形时的折迭弹翼机构防变形卡滞可靠性分析

提出了考虑弹性变形时弹翼展开机构防变形卡滞的可靠性分析方法,研制了相应程序,并给出了算例。     

YAG单晶基片的精密抛光及SPM检测

利用扫描探针显微镜(SPM)对YAG单晶基片精密加工表面进行了检测,获得了YAG单晶基片表面及表面层的基本特征,表明了SPM作为表面物理量检测是一种重要显微工具.     

电子环束流对航天器表面电位和等离子体鞘层的影响

采用二维三分量静电粒子模拟程序研究了电子环束流对低轨道磁化等离子体中运行的航天器表面电位和等离子体鞘层结构的影响.当有电子束流平行磁场入射时,航天器表面所带负电位的绝对值将增大.电子束流的速度和密度的增加将使航天器表面负电位绝对值增加很快.与此同时等离子体鞘层的尺度也将增大,形状将由向尾部延伸的“泪滴”状变成向两侧展开的“机翼”状.当电子环束流以相对于磁场成一定角度斜入射时,由于磁场的约束作用,航天器表面负电位的绝对值将随入射角增大而减小.      

带副翼的翼身组合体绕流的 Euler方程解

提出了一种求解带副翼偏转的翼身组合体绕流的Euler 方程计算方法.将对接分区网格与分区求解算法相结合,有效地求解了绕此外形的复杂流动.提出了一种满足通量守恒的内边界耦合条件.数值方法中选用Van Leer 分裂格式离散无粘通量项,并构造了一种限制器(Limiter)函数以保证TVD性质.数值算例表明本文方法是求解带操纵面偏转的翼身组合体绕流的有效方法.