液体圆柱射流破碎过程的实验

采用高速摄像仪对圆柱射流的表面剥离现象和射流破碎长度进行了实验,在低速射流下,分析了Rayleigh模式下主液滴和卫星液滴形成过程及运动规律.随着射流速度的增大,射流表面开始出现了表面剥离小液滴.并发现存在一个临界雷诺数,当超过临界雷诺数时,射流表面出现表面剥离现象.通过对射流中表面剥离现象的实验和分析,给出了两种射流破碎长度随雷诺数变化规律和破碎长度拟合关系式.      

SolidWorks二次开发在燃面计算中的应用

以SolidWorks二次开发接口为基础,探讨了参数化设计在固体火箭发动机装药燃面计算中的应用.通过不同的药柱建模方法实现了固体药柱的装药计算,发展了一种更为简单准确的燃面计算方法.计算结果表明,理论计算和试验结果吻合得较好,能够较好地模拟固体药柱的燃烧过程,可以满足工程计算上的需要,为固体装药的燃面计算提供了新的思路和方法.      

Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

浮力磨粒球性能对工件抛光影响的实验研究

从制作浮力磨粒球材料的性能参数和加工参数入手,综合考虑影响抛光加工的多种因素,应用实验分析方法,研究了磨粒球的直径、磨粒球的层厚和浮力磨粒球抛光工件时的去除量、加工件表面品质的关系.并对抛光工件时浮力磨球的浮力对工件抛光的影响作了分析.     

An adaptive integration surface for predicting transonic rotor noise in hovering and forward flights

In this paper, a new permeable adaptive integration surface is developed in order to evaluate transonic rotor noise in accordance with FW-H_pds equations(Ffowcs Williams-Hawkings equations with penetrable data surface). Firstly, a nonlinear near-field solution is computed on the basis of Navier-Stokes equations, which is developed on moving-embedded grid methodology.The solution calculated through the present CFD method is used as the input for acoustic calculations by FW-H_pds equations. Then, two criteria for constructing integration surfaces are established based on the analysis of the quadrupole source strength and the nonlinear characteristic.A new surface is determined adaptively by the pressure gradient or density in a given flowfield,eschewing the uncertainties associated with determining cylinder-shaped integration surfaces. For varying hover cases, transonic noises are simulated with new integration surfaces for a UH-1 model rotor. Furthermore, numerical results of the new integration surface derived from the density perturbation value conform better to experimental data than results derived from the pressure gradient.Finally, the integration surface given by jrqj being 0.1, which is an applicable criterion obtained from hover cases, is used to predict transonic rotor noise in forward flight. The computational accuracy of the new integration surface method has been validated in predicting transonic rotor noise of an AH-1 model rotor at different advance ratios.     

超薄层C—N共渗研究

用自行研制伯低真空化学热处理多用炉进行低真空脉冲式碳－氮共渗试验。研究渗剂组成及配比、工作压力、脉冲工艺周期、共渗温度与时间对渗层特性的影响。研究结果表明，在适当的工艺条件下，低真空脉冲式碳一氮共渗工艺能满足机械零件表面硬化层深度０．１－－０．３ｍｍ，硬度≥５８ＨＲＣ的要求。     

三维曲面测量新方法：半球头测量法

提出的半球头测量法从理论上消除了三维曲面截形测量时由于被测曲面的扭曲对测头所造成的干涉,使曲面测量直接转化为曲线测量,从而简化了测量和数据处理过程,为曲面测量提供了一种既简便实用又具有较高精度的新方法。     

颗粒增强锌基复合材料断裂与断口分析

为探讨颗粒增强低熔点金属基复合材料的性能和断裂特性，扩大锌合金的应用范围，本项工作采用流变铸造法制备了ＳｉＣｐ／Ｚｎ，Ａｌ２Ｏ３ｐ／Ｚｎ基复合材料，对该材料进行了冲击韧性、弯曲强度、压缩强度等性能测试，观察了其断口形貌，分析了其断裂特性，提出了此类复合材料的断裂模式。文中还讨论了增强颗粒的表面处理、粒子含量、粒径大小、粒于种类、基体合金种类对复合材料性能的影响。     

非定常Hele-Shaw流中Darcy定理的实验研究

对表面水波在H—S槽中的传播进行了实验研究和理论分析．通过对水波的复波数的测量验证Darcy定理在非定常H—S流中的适用性。研究表明，水面波在H—S槽中的传播．具有较强的衰减现象。同时．其复波数的实部与Darcy理论预测吻合．而其虚部与理论预测相差甚远。表明在非定常情况下，Darcy定理有局限性，有必要进一步研究。     

关于有理Bézier曲面片的几何连续拼接问题

本文深入研究了有理Bézier曲面片的几何连续拼接问题,给出了GC~1拼接条件的显式表示和判断两曲面片GC~1拼接状况的判定条件。用此条件可编写一简单程序,通过输入两曲面片的控制顶点及权因子,便可以“YES”或“NO”的输出回答两曲面片的拼接是否为GC~1连续。在非GC~1拼接时,可对称地修改两曲面片使其GC~1拼接。最后,本文给出了几种CAD/CAM工程中实用的充分条件。