全文获取类型
收费全文 | 357篇 |
免费 | 69篇 |
国内免费 | 161篇 |
专业分类
航空 | 409篇 |
航天技术 | 70篇 |
综合类 | 56篇 |
航天 | 52篇 |
出版年
2024年 | 1篇 |
2023年 | 8篇 |
2022年 | 10篇 |
2021年 | 19篇 |
2020年 | 23篇 |
2019年 | 24篇 |
2018年 | 19篇 |
2017年 | 25篇 |
2016年 | 26篇 |
2015年 | 31篇 |
2014年 | 29篇 |
2013年 | 19篇 |
2012年 | 35篇 |
2011年 | 26篇 |
2010年 | 19篇 |
2009年 | 22篇 |
2008年 | 20篇 |
2007年 | 22篇 |
2006年 | 30篇 |
2005年 | 26篇 |
2004年 | 16篇 |
2003年 | 20篇 |
2002年 | 7篇 |
2001年 | 16篇 |
2000年 | 13篇 |
1999年 | 9篇 |
1998年 | 11篇 |
1997年 | 2篇 |
1996年 | 5篇 |
1995年 | 9篇 |
1994年 | 10篇 |
1993年 | 9篇 |
1992年 | 5篇 |
1991年 | 6篇 |
1990年 | 5篇 |
1989年 | 6篇 |
1988年 | 4篇 |
排序方式: 共有587条查询结果,搜索用时 15 毫秒
141.
142.
In real machining, the tool paths are composed of a series of short line segments, which constitute groups of sharp corners correspondingly leading to geometry discontinuity in tangent. As a result, high acceleration with high fluctuation usually occurs. If these kinds of tool paths are directly used for machining, the feedrate and quality will be greatly reduced. Thus, generating continuous tool paths is strongly desired. This paper presents a new error-controllable method for generating continuous tool path. Different from the traditional method focusing on fitting the cutter locations, the proposed method realizes globally smoothing the tool path in an error-controllable way. Concretely, it does the smoothing by approaching the newly produced curve to the linear tool path by taking the tolerance requirement as a constraint. That is, the error between the desired tool path and the G01 commands are taken as a boundary condition to ensure the finally smoothed curve being within the given tolerance. Besides, to improve the smoothing ability in case of small corner angle, an improved local smoothing method is also proposed by symmetrically assigning the control points to the two adjacent linear segments with the constrains of tolerance and G3 continuity. Experiments on an open five-axis machine are developed to verify the advantages of the proposed methods. 相似文献
143.
144.
为了研究TC11钛合金铣削加工过程中刀具磨损对加工表面质量的影响规律,设计了刀具磨损与铣削表面粗糙度、表面残余应力的试验。结果表明:TC11钛合金铣削加工过程中的刀具磨损可以分为:初期磨损、正常磨损、剧烈磨损三个阶段。当刀具处于"初期磨损"时,TC11铣削表面粗糙度随切削时间逐渐减小,铣削表面残余应力也呈减小趋势;当刀具处于"正常磨损"阶段时,铣削表面粗糙度和铣削表面残余应力都呈增加趋势,但增加的速度平稳;当刀具进入"剧烈磨损"阶段时,铣削表面粗糙度迅速增大,表面残余应力也较前两个阶段显著增加。另外,试验过程中的TC11铣削表面残余应力均表现为压应力。 相似文献
145.
基于SYSWELD有限元分析软件,以某新型战术型号铝合金联装架为产品对象,选取支撑框配对组件、弹位组件和立方体组件为典型结构件进行焊接残余应力和变形数值模拟,以期表征铝合金联装架焊接过程的残余应力分布和变形趋势。结果表明:焊缝及其附近热影响区的Von-Mises应力较高,甚至超过了5A06铝合金材料的常温屈服强度;支撑框组件焊后最大变形出现于长矩形管中央,约为6.44 mm;弹位组件的焊接变形整体表现为凹向三维结构内腔,焊接变形也多集中在长矩形管上,最大变形约为5.21 mm。另外,采用对称分散焊过程产生的焊接变形量小于逐条焊缝焊接过程,但焊接残余应力趋势则相反。 相似文献
146.
147.
星载运动附件扰动抑制方法研究 总被引:1,自引:0,他引:1
为改善高分七号卫星(GF-7)在附件(特别是双轴定向天线)运动时的姿态稳定度,研究了星载附件指向运动平滑及其扰动抑制方法。首先,针对卫星姿态扰动主要来源于对地数传天线对地面通信目标的快速捕获运动的情况,通过引入具有角速度全局光滑性的路径平滑技术对天线的目标捕获过程进行规划;其次,针对含有双轴运动天线的整星姿态运动,建立了适用于任意星体运动速度下的一般动力学方程,并进行了对比验证。进而根据规划后的天线运动引起的扰动力矩对姿态控制系统引入前馈补偿,从而抑制天线运动对整星姿态的扰动影响。基于提出的扰动抑制方法进行数值仿真,结果表明,运动平滑与力矩补偿结合的协同控制技术可将天线扰动削减90%以上。 相似文献
148.
149.
150.