The First Chinese Ocean Color Satellite HY-1A

HY-1A is China's first ocean color satellite, and was launched on 15 May 2002as a piggyback satellite on the FY-1D satellite using the Long March rocket.There are two sensors on the satellite: China's Ocean Color and Temperature Scanner (COCTS), and the CCD Coastal Zone Imager (CZI). In the report,first, the properties and characteristics of HY-1A are briefly introduced; Second, the quality and availability of the data are evaluated by the mean of the Complex Signal Noise Ratio (CSNR) which is simulated theoretically; Third,the received HY-1A data are compared with SeaSTAR data to understand the accuracy of radiance measurement by the HY-1A; Finally, the remote sensing products of ocean color and temperature are mapped by HY-1A to study its application potentiality. The results show that the HY-1A has a latent capability for the application of marine environment detection, the management and protection of marine resources, and the furthering of national rights and interests.Meanwhile, some modifications are proposed for the next ocean satellite, suchas adding the case of tilt scanning, modification of the CCD element uniformity,and adding more ocean satellite receiving stations.     

5A90铝锂合金型材折斜角成形性能的试验研究

型材一次折斜角成形是航空零件制造工艺的重要方法之一。本文通过新研制的5A90铝锂合金型材折斜角成形试验的研究，得到了极限开斜角和闭斜角值，为新机的设计及生产工艺提供了重要的指导依据。     

民用飞机25.831d排烟适航条款和咨询通告研究

民用飞机的排烟能力直接影响到座舱出现烟雾情况下的飞行安全,对CCAR 25.831(d)条款和对应的咨询通告25-9A进行研究,为民用飞机座舱排烟的设计和适航验证提供支持。     

Formability enhancement in hot spinning of titanium alloy thin-walled tube via prediction and control of ductile fracture

The damage and fracture in hot spinning of titanium alloy is a very complex process under the combined effects of microstructure evolution and stress state. In this study, their dependences on processing parameters were investigated by an integrated FE model considering microstructure and damage evolution, and revealing the effects of microstructure and stress states on damage evolution. The results show that the inner surface of workpiece with the largest voids volume fraction is the place with...     

随钻测斜用微小型导航计算机系统设计与实现

为了满足随钻测斜仪器在油气井中恶劣环境下的测量要求,本文提出了一种以数字信号控制器（DSC）和FPGA组成的双CPU导航计算机方案。该系统由DSC（dsPIC30F6014A）作为核心处理器完成导航计算和滤波算法;由FPGA完成对IMU（惯性测量单元）数据的采集控制及传输等功能。DSC与FPGA之间通过串口传输,最终导航结果由DSC输出给外部控制设备。该系统很好的满足了随钻测斜仪的性能尺寸要求,试验验证结果表明倾斜角、方位角、和工具面角均达到了预期精度指标。     

Prediction of forming limit curve （FLC） for AI-Li alloy 2198-T3 sheet using different yield functions

The Forming Limit Curve （FLC） of the third generation aluminum-lithium （Al-Li） alloy 2198-T3 is measured by conducting a hemispherical dome test with specimens of different widths. The theoretical prediction of the FLC of 2198-T3 is based on the M-K theory utilizing respectively the von Mises, Hill＇48, Hosford and Barlat 89 yield functions, and the different predicted curves due to different yield functions are compared with the experimentally measured FLC of 2198-T3. The results show that though there are differences among the four predicted curves, yet they all agree well with the experimentally measured curve. In the area near the planar strain state, the predicted curves and experimentally measured curve are very close. The predicted curve based on the Hosford yield function is more accurate under the tension-compression strain states described in the left part of the FLC, while the accuracy is better for the predicted curve based on Hill＇48 yield function under the tension-tension strain states shown in the right part.     

Prediction of forming limit curve (FLC) for Al-Li alloy 2198-T3 sheet using different yield functions

The Forming Limit Curve (FLC) of the third generation aluminum-lithium (Al-Li) alloy 2198-T3 is measured by conducting a hemispherical dome test with specimens of different widths. The theoretical pred...     

Wire electrochemical machining with axial electrolyte flushing for titanium alloy

Titanium and its alloys have found very wide application in aerospace due to their excellent characteristics although their processing is still a challenge. Electrochemical machining is an important issue in the fabrication of titanium and titanium alloys. Wire electrochemical machining (WECM) is mainly used for workpiece cutting under the condition of different thickness plates. It has a great advantage over wire electro-discharge machining, which is the absence of heat-affected zone around the cutting area. Moreover, the wire electrode in WECM could be used repetitively because it is not worn out. Thus, much attention has been paid to WECM. The effective way of removing electrolysis products is of importance to WECM. In this paper, the axial electrolyte flushing is presented to WECM for removing electrolysis products and renewing electrolyte. The Taguchi experiment is conducted to optimize the machining parameters, such as wire feedrate, machining voltage, electrolyte concentration, etc. Experimental results show that WECM with axial electrolyte flushing is a promising issue in the fabrication of titanium alloy (TC1). The feasibility of multi-wire electrochemical machining is also demonstrated to improve the machining productivity of WECM.     

5083铝合金力学性能的球压痕法检测研究

介绍了微压痕法在航空铝合金材料力学性能检测的研究.采用球形压头通过多级循环加载方法得到了5083铝合金材料压痕深度与载荷的关系,将微压痕数据输入经过充分训练的人工神经网络模型,计算出材料力学性能参数和材料应力应变曲线,对压痕法测量得到的材料真应力应变曲线与拉伸试验得到的结果进行了比较.     

双层板激光焊接/ 超塑成形数值模拟及工艺研究

选取TC4 钛合金四层板加强结构中双层板为研究对象,采用激光穿透焊接工艺代替传统超塑成

形/ 扩散连接(SPF/ DB)工艺中涂止焊剂连接。借助ABAQUS 有限元分析软件对超塑成形过程进行分析,得到

优化的压力-时间(p-t)曲线,作为双层板超塑成形过程的气压加载曲线,进行实验验证。结果表明:成形后零

件壁厚分布均匀,焊缝处无撕裂现象,与有限元模拟结果保持一致;用此新工艺代替传统SPF/ DB 工艺中的止

焊剂具有可行性。