应用数字图象处理技术研究涡流场

本文描述的实验采用干冰为示踪粒子，对脱体涡系作了流动显示，并对摄取的图片进行了数字图象处理。结果清楚地提示了涡的三层结构。在主涡的诱导下，出现二次涡，而二次涡会影响脱体涡的速度分布。实验还得到了脱体涡流场的灰度分布图，并将得出的涡核直径与ＬＤＶ得到的结果进行了对比。实验结果还证明来流迎角、侧滑角及前缘后掠角会影响涡核的位置和强度。当机翼前缘后掠角增加时，脱体涡向不稳定方向发展。     

穿透式冷板的传热分析

对航空电子设备上采用的空心冷板冷却系统的传热特性进行了分析求解，得到了空心冷板稳态温度分布表达工和功率－温度－流量关系式，可作为空心冷板系统的设计依据，建立了空心冷板失效的动态温度模型，得到的温度－时间响应特性可用于评估冷板系统耐热冲击性能。     

民机营运维修保障系统仿真

阐述了民机维修保障仿真系统，并讨论了它与民机可靠性，维修性和经济性仿真大系统的关系。文中重点介绍了民机营运阶段维修保障系统仿真建模及其应用软件ＣＡＲＭＥＳ的功能模块设计，最后以国内某航空公司营运的Ｙ－７飞机为例对其ＲＭＥ进行分析和评价。     

A320系列飞机机身抖动现象浅析

针对A320系列飞机在营运过程中产生间断性水平或垂直抖动故障，分析了产生抖动的原因，并通过更换作动器或操纵面铰链排除了抖动故障．同时提出了避免A320系列飞机交替产生不稳定因素的措施。     

波音757-200型飞机风挡加温系统故障的排除与总结

通过对一起波音757—200型飞机风挡加温系统故障的排除．对该型飞机风挡加温系统的组成及工作原理进行介绍，为类似故障的排除提供了借鉴经验。     

Suggestion for aircraft flying qualities requirements of a short-range air combat mission

Owing to the lack of a direct link with the operations in short-range air combat,conventional aircraft flying qualities criteria are inappropriate to guide the design of a task-tailored flight control law.By applying the mission-oriented flying qualities evaluation approach,various aircraft with different control law parameters are evaluated on a ground-based simulator.This paper compares the evaluation results with several conventional flying qualities criteria,and discusses the appropriate parameter combination to reflect the flying qualities requirements of short-range air combat,The comparison and analysis show that a short-range air combat mission requires a higher minimum short period mode natural frequency and a smaller maximum roll mode time constant,and allows a lower minimum pitch attitude bandwidth and a higher maximum short period mode damp ratio than those of conventional flying qualities criteria.Furthermore,a combination of the pitch attitude bandwidth,the pitch attitude magnitude at the bandwidth frequency,and the pitch attitude transfer function gain can define the flying qualities requirements of short-range air com bat.The new metric can successfully predict the flying quality levels of aircraft in a short-range air combat mission.     

支线飞机综合飞行仿真平台设计

针对支线飞机机械操纵系统的特点,设计了由模块化的功能单元组成的综合飞行仿真平台,可以实现机械操纵系统数字仿真,在支线飞机的设计与制造中有着重要的应用价值,此平台通过改进还可用于支线飞机的试飞科目训练,从而降低试飞风险并缩短研制周期。     

波音737NG飞机平尾内梁下蒙皮裂纹的修理

介绍了水平安定面内梁下蒙皮裂纹的成因以及发现裂纹后的修理方法，结合定检维修经验对裂纹损伤修理方案和经常出现的问题进行了分析总结，并给出了修理工期控制的建议。     

双框架飞机蒙皮检测机器人切换运动控制方法

针对一种双框架飞机蒙皮检测机器人,通过分析该机器人在飞机表面上的受力情况,在飞机表面该机器人受到了非完整约束,基于牛顿-欧拉法建立了机器人非完整约束动力学模型。根据机器人机械结构和运动步态分析,将该非完整机器人系统分为子系统A和子系统B。为了实现机器人在飞机表面运动,采用反演技术和快速Terminal滑模控制相结合的思想对系统设计了控制器,提出了一种反演-滑模控制方法;对于非完整机器人子系统A和子系统B,设计了一种基于事件驱动的切换策略,实现了机器人对期望轨迹的全局渐近跟踪,并利用Lyapunov稳定性证明系统的跟踪误差收敛。仿真和试验表明,采用该切换策略和反演-滑模控制方法,双框架飞机蒙皮检测机器人可以在飞机表面自由运动并进行损伤检测,具有良好的可靠性和稳定性。     

A compliant polymorphing wing for small UAVs

This paper presents the development of a novel compliant polymorphing wing capable of chord and camber morphing for small UAVs. The morphing wing can achieve up to 10% chord extension and ±20° camber changes. The design, modeling, sizing, manufacturing and mechanical testing of the wing are detailed. The polymorphing wing consists of one continuous front spar fixed to the fuselage and a rear spar on each side of the wing. Each rear spar can translate in the chordwise direction (chord morphing) and rotate around itself (camber morphing). A flexible elastomeric latex sheet is used as the skin to cover the wing and maintain its aerodynamic shape whilst allowing morphing. The loads from the skin are transferred to the spars using the compliant cellular ribs that support the flexible skin and facilitate morphing. Pre-tensioning is applied to the skin to minimize wrinkling when subject to aerodynamic and actuation loads. A rack and pinion actuation system, powered by stepper motors, is used for morphing. Aero-structural design, analysis and sizing are conducted. Performance comparison between the polymorphing wing and the baseline wing (non-morphing) shows that chord morphing improves aerodynamic efficiency at low angles of attack while camber morphing improves efficiency at high angles of attack.