Motion synchronization in a dual redundant HA/EHA system by using a hybrid integrated intelligent control design

This paper presents an integrated fuzzy controller design approach to synchronize a dis-similar redundant actuation system of a hydraulic actuator (HA) and an electro-hydrostatic actu-ator (EHA) with system uncertainties and disturbances. The motion synchronous control system consists of a trajectory generator, an individual position controller for each actuator, and a fuzzy force tracking controller (FFTC) for both actuators. The trajectory generator provides the desired motion dynamics and designing parameters of the trajectory which are taken according to the dynamic characteristics of the EHA. The position controller consists of a feed-forward controller and a fuzzy position tracking controller (FPTC) and acts as a decoupled controller, improving posi-tion tracking performance with the help of the feed-forward controller and the FPTC. The FFTC acts as a coupled controller and takes into account the inherent coupling effect. The simulation results show that the proposed controller not only eliminates initial force fighting by synchronizing the two actuators, but also improves disturbance rejection performance.     

Multi-level virtual prototyping of electromechanical actuation system for more electric aircraft

Electromechanical actuators (EMAs) are becoming increasingly attractive in the field of more electric aircraft because of their outstanding benefits, which include reduced fuel burn and maintenance cost, enhanced system flexibility, and improved management of fault detection and isolation. However, electromechanical actuation raises specific issues when being used for safety-critical aerospace applications like flight controls: huge reflected inertia to load, jamming-type failure, and increase of backlash with service due to wear and local dissipation of heat losses for thermal balance. This study proposes an incremental approach for virtual prototyping of EMAs. It is driven by a model-based system engineering process in order to enable simulation-aided design. Best practices supported by Bond graph formalism are suggested to develop a model’s structure efficiently and to make the model ready for use (or extension) by addressing the above mentioned issues. Physical effects are progressively introduced, and the realism of lumped-parameter models is increased step-by-step. In particular, multi-level component models are architected to ensure continuity between engineering activities. The models are implemented in the AMESim simulation environment, and simulation responses are given to illustrate how they can be used for preliminary sizing, control design, thermal balance verification, and faults to failure analysis. The proposed best practices intend to provide engineers with fast, reusable, and efficient means to assess performance virtually and enhance maturity, performance, and robustness.     

均匀各向同性大气湍流对声爆传播特性的影响

基于离散Fourier模态有限和生成的随机大气湍流场，采用修正波形参数方法，开展了均匀各向同性大气湍流对典型超声速客机声爆传播特性的影响分析。计算采用的超声速客机模型为自行生成的简化超声速公务机模型。首先，应用航空工业空气动力研究院自主研制的CFD软件ARI_Overset在三维空间求解Navier-Stokes方程，得到作为声爆远场传播初始值的近场空间压力分布；其次，基于Von Karman能量谱，采用离散Fourier模态有限和形式生成随机均匀各向同性大气湍流场；最后，采用修正波形参数方法模拟了声爆信号在随机速度湍流场中的传播过程。数值结果表明：各向同性大气湍流对于地面声爆特征有重要影响。与无湍流状态相比，均匀各向同性大气湍流使得地面声爆特征增强的概率约为55%，使得地面声爆特征减弱的概率约为45%，故总体而言大气湍流效应更倾向于增强地面声爆特征；均匀各向同性大气湍流对于声爆传播路径影响相对较小，但是这一变化仍会导致地面信号接收点的不确定性。     

基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.     

数理统计方法在部件故障控制中的应用研究

机载部件的可靠性直接影响航空器的安全运行。本文通过对机载部件使用寿命的统计和失效分析,对部件的故障提出了有效的控制方法,并举例说明了此方法在维护中的使用。     

Aircraft nonlinear stability analysis and multidimensional stability region estimation under icing conditions

Icing is one of the crucial factors that could pose great threat to flight safety,and thus research on stability and stability region of aircraft safety under icing conditions is significant for control and flight.Nonlinear dynamical equations and models of aerodynamic coefficients of an air craft are set up in this paper to study the stability and stability region of the aircraft under an icing condition.Firstly,the equilibrium points of the iced aircraft system are calculated and analyzed based on the theory of differential equation stability.Secondly,according to the correlation theory about equilibrium points and the stability region,this paper estimates the multidimensional stability region of the aircraft,based on which the stability regions before and after icing are compared.Finally,the results are confirmed by the time history analysis.The results can give a reference for stability analysis and envelope protection of the nonlinear system of an iced aircraft.     

基于ALE法的水陆两栖飞机船体着水性能分析

水陆两栖飞机的着水性能是体现其综合性能的重要因素之一.应用ALE法对三种水陆两栖飞机船体截面进行入水仿真计算,从着水载荷、喷溅性能及运动响应三个方面对着水性能进行综合评估.对比分析了直线型、带舭弯弧形、复合型三种构型截面在不同速度、不同重量下的压力分布、喷溅性能以及运动响应,得到了三种截面横向压力分布规律.计算结果显示相同状态下,喷溅性能复合型优于带舭弯弧形、带舭弯弧形优于直线型;过载复合型远大于带舭弯弧形,带舭弯弧形稍大于直线型,综合看来带舭弯弧形截面着水性能最佳.     

军用飞机型号研制试飞费用估算研究

在借鉴国外经验的基础上,对国内军用飞机型号研制试飞费用的构成进行了研究,提出基于兰德DAPCA IV模型的军用飞机型号研制试飞费用估算模型,为试飞费用的估算提供了依据。     

维修方案项目优化的可靠性分析方法

通过可靠性管理对民用航空器维修方案的动态监控,实施对维修方案项目执行情况的跟踪和可靠性分析,以机队实际运行数据为背景,提出对维修方案项目管理系统性的优化和管理方法,以使航空公司的维修方案更加符合机队的实际使用和维护特点,进一步提高机队的运行效率、降低维修成本和提高航班准点率。     

基于快速非奇异终端滑模的姿态控制技术

针对存在执行器故障与外部干扰的刚体飞行器姿态控制系统,提出一种基于快速非奇异终端滑模(NSFTSM)的姿态容错控制方法.控制方法不仅保证姿态机动过程的快速性,而且避免了传统的终端滑模面所带来的奇异性问题.采用二阶鲁棒精确微分器估计执行器故障与外部干扰,采用快速非奇异终端滑模技术设计姿态容错控制律,根据Lyapunov稳定性理论证明了方法的稳定性.稳定性分析表明,通过引入新型快速非奇异终端滑模,控制器使得闭环系统能够快速收敛到滑模面的微小邻域内,进而收敛到系统平衡点的微小邻域内,并且系统对外部干扰具有较强的鲁棒性.数值仿真结果验证了方法在姿态跟踪控制中的有效性.