脉冲式转速表的设计,校验与应用

本文就航空发动机转速测量技术状态进行了简要分析,对适用于超轻型飞机的具有原理、结构简单,造价低等优点的“脉冲式转速表”的设计、校验等进行了详细的论述,并对该原理的推广应用进行了分析讨论。     

三维瞬态导热温度场边界元计算及一阶数学奇异的处理

推导了三维瞬态导热温度场边界元解法的积分方程和离散代数方程，并编制了相应的计算机程序，采用坐标变换的解析消去法，处理边界元的一阶数学奇异点，从而提高了算法的数值精度。用本程序计算了正方体和圆柱环瞬态导热温度场，数值解与解析解的吻合程度令人满意。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

钛合金板材激光弯曲成形的研究

 对常温下钛合金板材进行了激光弯曲成形研究。分析了激光功率、扫描速度、光斑大小对板材弯曲变形的影响,获得理想工艺参数范围为:功率1 .0～1 .2 k W、扫描速度2～3 m/min、光斑直径6～7mm。同时分析了板材厚度、宽度及扫描次数对材料弯曲变形的影响,为钛合金板材弯曲成形提供了一种新途径。     

双温度试验系统方案设计

结合双温度试验系统方案设计,介绍了可编程控制器在温度控制上的应用,有助于增进读者对PLC等的了解。     

翼型风洞侧壁干扰的数值模拟研究

运用Navier-Stokes数值模拟对翼型模拟试验对风洞侧壁干扰进行模拟，将简单代数湍流模型扩展用于机翼／风洞侧壁结合区流动，分析了风洞实验侧壁干扰问题的形成机理和影响翼型实验侧壁干扰的各种因素，如翼型展长、风洞侧壁边界层厚度及侧壁边界层抽吸等，对实验结果的影响，得出了一些有用的结论。计算格式空间采用中心有限体积离散，时间采用多步Runge-Kutta时间步长格式进行积分。计算结果证明了该方法的可行性和优越性。     

热暴露对IMI834近α高温钛合金组织和拉伸性能的影响

测试了ＩＭＩ８３４高温钛合金在６００～７５０℃的空气中热暴露１００小时后拉伸性能，利用透射电镜和扫描电镜观察了合金暴露前后的组织变化及拉伸断口，认为表面氧化是造成合金热暴露后塑性下降的主要原因，但基体组织内有序α２相和硅化物的析出变化也在不同程度上造居了合金热暴露后的强度和塑性的下降。     

机载小惯量探针研制及在飞机武器发射中的应用

介绍了一种用于飞机武器发射时测量发动机进口动态温升时序的机载小惯量探针,以其独特的研制方法,较好地解决了机载小惯量测温装置、频响与可靠性兼顾这一测试难题,并在武器发射时,成功地用来评价发动机工作稳定性的影响。     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.     

吸气条件对圆柱非定常分离流影响的数值研究

本文根据二维可压非定常Ｎ－Ｓ方程，基于Ｂｅａｍ ａｎｄ Ｗａｒｍｉｇｎ及Ｓｔｅｇｅｒ的方法，在圆柱绕流出现周期分离后，施加吸气条件，研究气对于圆柱非定常绕流的影响，计算结果表明，在恰当地区域施加恰当的吸气条件，可以希望通过减小压差阻力来减小总阻力，吸气还有抑制尾迹中非对称流动的作用，从而使圆柱所受的垂直于来流方向的升力的变化幅度减小，变化频率减小，但是吸气会增加磨擦阻力，过份的吸气会导致摩阻增大太