某型蒸发式稳定器气动及燃烧特性研究

为解决亚燃冲压发动机在高速低温来流条件下的可靠点火、火焰稳定和高效燃烧问题,对某型蒸发式火焰稳定器分别进行了冷态流场和燃烧流场的数值研究,并与常规V型火焰稳定器进行了对比分析。研究结果表明:在给定范围内,蒸发式稳定器随来流速度的增大,总压恢复系数和停留时间明显减小,回流区长度、回流率和燃烧效率变化不大;与相同槽宽的常规V型火焰稳定器相比,回流率明显减小,总压恢复系数、回流区长度和停留时间略有减小。蒸发式稳定器后部形成明显的回流区,且基本上不受外部主流流动的干扰,通过单独控制稳定器局部供油,可以使稳定器在最佳油气比下工作,有利于在高速来流条件下可靠工作。     

A closed-form solution for moving source localization using LBI changing rate of phase difference only

Due to the deficiencies in the conventional multiple-receiver localization systems based on direction of arrival(DOA) such as system complexity of interferometer or array and amplitude/phase unbalance between multiple receiving channels and constraint on antenna configuration,a new radiated source localization method using the changing rate of phase difference(CRPD)measured by a long baseline interferometer(LBI) only is studied. To solve the strictly nonlinear problem, a two-stage closed-form solution is proposed. In the first stage, the DOA and its changing rate are estimated from the CRPD of each observer by the pseudolinear least square(PLS) method,and then in the second stage, the source position and velocity are found by another PLS minimization. The bias of the algorithm caused by the correlation between the measurement matrix and the noise in the second stage is analyzed. To reduce this bias, an instrumental variable(IV) method is derived. A weighted IV estimator is given in order to reduce the estimation variance. The proposed method does not need any initial guess and the computation is small. The Cramer–Rao lower bound(CRLB) and mean square error(MSE) are also analyzed. Simulation results show that the proposed method can be close to the CRLB with moderate Gaussian measurement noise.     

A theoretical model of semi-elliptic surface crack growth

A theoretical model of semi-elliptic surface crack growth based on the low cycle strain damage accumulation near the crack tip along the cracking direction and the Newman–Raju formula is developed. The crack is regarded as a sharp notch with a small curvature radius and the process zone is assumed to be the size of cyclic plastic zone. The modified Hutchinson, Rice and Rosengren(HRR) formulations are used in the presented study. Assuming that the shape of surface crack front is controlled by two critical points: the deepest point and the surface point.The theoretical model is applied to semi-elliptic surface cracked Al 7075-T6 alloy plate under cyclic loading, and five different initial crack shapes are discussed in present study. Good agreement between experimental and theoretical results is obtained.     

Flutter analysis of an airfoil with nonlinear damping using equivalent linearization

The equivalent linearization method （ELM） is modified to investigate the nonlinear flut- ter system of an airfoil with a cubic damping. After obtaining the linearization quantity of the cubic nonlinearity by the ELM, an equivalent system can be deduced and then investigated by linear flut- ter analysis methods. Different from the routine procedures of the ELM, the frequency rather than the amplitude of limit cycle oscillation （LCO） is chosen as an active increment to produce bifurca- tion charts. Numerical examples show that this modification makes the ELM much more efficient. Meanwhile, the LCOs obtained by the ELM are in good agreement with numerical solutions. The nonlinear damping can delay the occurrence of secondary bifurcation. On the other hand, it has marginal influence on bifurcation characteristics or LCOs.     

激波聚焦诱导气液两相爆震燃烧的数值模拟

对以激波聚焦和增加障碍物方式诱导煤油-空气气液两相爆震燃烧的过程进行了数值模拟.采用欧拉-拉格朗日方法建立了脉冲爆震发动机(PDE)中气液两相流的喷射、雾化、掺混过程.研究发现环形爆震波在爆震管凹腔内经过反射、汇聚后能够引燃可燃混合物.而在障碍物处,激波的反射和再反射聚焦能够形成高温高压点(2700K,25MPa),产生局部爆炸,有助于形成稳定的脉冲爆震燃烧(波面速度为1900m/s,温度为2 950K),有效地缩短由缓燃向爆震转变(DDT)距离至0.45m.     

基于自适应粒子滤波的涡扇发动机故障诊断

针对涡扇发动机非线性、非高斯的特点,提出了一种自适应的粒子滤波算法用于涡扇发动机气路部件突变故障的诊断.为了减小算法的计算量并且保证滤波精度,分析了滤波精度和样本数目的关系,提出根据滤波过程中状态的方差自适应地调整粒子数,在保证一定的滤波精度下可以有效地减少滤波过程中使用的粒子数,提高了算法的实时性.同时,引入扩展卡尔曼滤波(EKF)用于更新粒子,产生重要概率密度函数,在一定程度上避免了粒子的退化.通过某型涡扇发动机的仿真分析表明:改进的算法相比标准粒子滤波算法用于涡扇发动机气路部件故障诊断时,参数估计的方均根误差减小了50%左右,且算法的计算量减小了30%.     

WP7系列发动机涡轮导向器叶片盖板的钎焊修复

采用真空钎焊的方法对WP7系列发动机涡轮导向器叶片盖板进行了修复,介绍了修复过程及工艺。修复后的叶片经目视及荧光检验未发现表面裂纹,该修复工艺已成功用于WP7系列发动机涡轮导向器叶片盖板的批量修复,年修复量约1000件。     

RR公司3转子民用发动机技术发展思路

为了探寻RR公司在民用航空发动机领域中的技术和产品发展思路,对该公司3转子民用发动机产品的发展历程和市场情况以及发展的外部条件进行了简要回顾分析。介绍了RR公司3转子发动机的总体布局方案,并通过对波音787客机所使用的典型3转子发动机与双转子发动机的对比,分析了3转子布局技术特点。归纳总结出RR公司3转子民用发动机的技术发展思路的特点:大胆尝试、紧扣市场、低压部件与核心机协调发展和应用缩放技术。     

基于滑模自适应控制的不确定混沌系统修正函数投影同步

研究了一类不确定混沌系统的修正函数投影同步。首先,设计了一类滑模曲面;基于该曲面设计了同步控制器,并采用自适应技术设计了自适应律对不确定参数进行逼近。在一定条件下,该同步控制方案可以实现2个不确定异结构混沌系统的修正函数投影同步。然后,为保证合适的控制量,对控制增益进行了优化。从同步效果来看,所设计的控制器对混沌系统的不确定项的影响具有较强的鲁棒性。最后,数值仿真验证了该控制器的有效性和可行性。     

弹道修正执行机构综述

二维弹道修正弹是一种低成本、高精度的精确打击弹药,修正机构是弹道修正弹上的重要部件,其性能决定了弹丸的弹道修正能力。针对弹道的二维修正需求,介绍了国内外对二维弹道修正弹修正机构的研究状况;列举了应用在二维弹道修正弹上不同类型的修正机构;阐述了不同类型修正机构的工作原理、特点以及各自的局限性。最后,对不同类型修正机构特性进行了比较,给出了相关技术指标,对比了各自的优缺点。阐述了选择和设计执行机构应注意的问题。