飞机附件的维修间隔决策

研究了飞机附件软时限的设定和管理方法,该方法可将附件的故障发生机率和运行风险控制在可接受水平,减少航空公司因机务原因的延误,提高飞机可利用率。     

双框架飞机蒙皮检测机器人切换运动控制方法

针对一种双框架飞机蒙皮检测机器人,通过分析该机器人在飞机表面上的受力情况,在飞机表面该机器人受到了非完整约束,基于牛顿-欧拉法建立了机器人非完整约束动力学模型。根据机器人机械结构和运动步态分析,将该非完整机器人系统分为子系统A和子系统B。为了实现机器人在飞机表面运动,采用反演技术和快速Terminal滑模控制相结合的思想对系统设计了控制器,提出了一种反演-滑模控制方法;对于非完整机器人子系统A和子系统B,设计了一种基于事件驱动的切换策略,实现了机器人对期望轨迹的全局渐近跟踪,并利用Lyapunov稳定性证明系统的跟踪误差收敛。仿真和试验表明,采用该切换策略和反演-滑模控制方法,双框架飞机蒙皮检测机器人可以在飞机表面自由运动并进行损伤检测,具有良好的可靠性和稳定性。     

Motion synchronization in a dual redundant HA/EHA system by using a hybrid integrated intelligent control design

This paper presents an integrated fuzzy controller design approach to synchronize a dis-similar redundant actuation system of a hydraulic actuator (HA) and an electro-hydrostatic actu-ator (EHA) with system uncertainties and disturbances. The motion synchronous control system consists of a trajectory generator, an individual position controller for each actuator, and a fuzzy force tracking controller (FFTC) for both actuators. The trajectory generator provides the desired motion dynamics and designing parameters of the trajectory which are taken according to the dynamic characteristics of the EHA. The position controller consists of a feed-forward controller and a fuzzy position tracking controller (FPTC) and acts as a decoupled controller, improving posi-tion tracking performance with the help of the feed-forward controller and the FPTC. The FFTC acts as a coupled controller and takes into account the inherent coupling effect. The simulation results show that the proposed controller not only eliminates initial force fighting by synchronizing the two actuators, but also improves disturbance rejection performance.     

基于Visual Basic的互感器负荷箱测量仪校准系统的实现

为解决互感器负荷箱测量仪同相分量和正交分量的校准问题,在分析互感器负荷箱测量仪工作原理的基础上,设计了基于电子/电工组合式的互感器负荷箱测量仪校准装置,并简要说明装置电工部分、电子部分以及上位机软件的实现。经省级计量研究院验证结果表明,该装置校准结果符合0.2级要求,可作为标准装置解决1级互感器负荷箱测量仪量值溯源问题。     

飞机数字化装配系统中机身交点孔加工方法研究

针对传统交点孔加工方法加工精度低且存在回弹变形的问题,设计了一种满足飞机大部件数字化装配要求的机身交点孔精加工方法,根据交点孔的加工特性完成了机身定位与固持、数控加工中心定位以及加工工艺的总体设计,确定了交点孔加工程序原点的计算方法和编程原则,最后通过交点孔试切加工试验验证了加工方法的可行性。     

基于6SPS并联机构标定新方法

系统研究6SPS并联机构标定的方法。研究中应用激光跟踪仪测量、基于并联机构正解和定位误差旋量的计算,正交试验进行试验设计,应用非线性最小二乘参数辨识。仿真验证辨识的几何误差可以等于假定值,试验验证位姿精度提高了10倍。     

Multi-level virtual prototyping of electromechanical actuation system for more electric aircraft

Electromechanical actuators (EMAs) are becoming increasingly attractive in the field of more electric aircraft because of their outstanding benefits, which include reduced fuel burn and maintenance cost, enhanced system flexibility, and improved management of fault detection and isolation. However, electromechanical actuation raises specific issues when being used for safety-critical aerospace applications like flight controls: huge reflected inertia to load, jamming-type failure, and increase of backlash with service due to wear and local dissipation of heat losses for thermal balance. This study proposes an incremental approach for virtual prototyping of EMAs. It is driven by a model-based system engineering process in order to enable simulation-aided design. Best practices supported by Bond graph formalism are suggested to develop a model’s structure efficiently and to make the model ready for use (or extension) by addressing the above mentioned issues. Physical effects are progressively introduced, and the realism of lumped-parameter models is increased step-by-step. In particular, multi-level component models are architected to ensure continuity between engineering activities. The models are implemented in the AMESim simulation environment, and simulation responses are given to illustrate how they can be used for preliminary sizing, control design, thermal balance verification, and faults to failure analysis. The proposed best practices intend to provide engineers with fast, reusable, and efficient means to assess performance virtually and enhance maturity, performance, and robustness.     

Multi-mode diagnosis of a gas turbine engine using an adaptive neuro-fuzzy system

Gas Turbine Engines (GTEs) are vastly used for generation of mechanical power in a wide range of applications from airplane propulsion systems to stationary power plants. The gas-path components of a GTE are exposed to harsh operating and ambient conditions, leading to several degradation mechanisms. Because GTE components are mostly inaccessible for direct measurements and their degradation levels must be inferred from the measurements of accessible parameters, it is a challenge to acquire reliable information on the degradation conditions of the parts in different fault modes. In this work, a data-driven fault detection and degradation estimation scheme is developed for GTE diagnostics based on an Adaptive Neuro-Fuzzy Inference System (ANFIS). To verify the performance and accuracy of the developed diagnostic framework on GTE data, an ensemble of measurable gas path parameters has been generated by a high-fidelity GTE model under (a) diverse ambient conditions and control settings, (b) every possible combination of degradation symptoms, and (c) a broad range of signal to noise ratios. The results prove the competency of the developed framework in fault diagnostics and reveal the sensitivity of diagnostic results to measurement noise for different degradation symptoms.     

基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.